BS EN 665-1995 Resilient floor coverings Determination of exudation of plasticizers《弹性地板覆盖物 增塑剂渗漏的测定》.pdf

1、BRITISH STANDARD BS EN 665:1995 Resilient floor coverings Determination of exudation of plasticizers The European Standard EN665:1994 has the status of a BritishStandardBSEN665:1995 This BritishStandard, having been prepared under the directionof the Materials and Chemicals Sector Board (I/-), waspu

2、blished under the authorityof the Standards Boardand comes into effect on 15February1995 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference PRI/60 Draft for comment 92/38639 DC ISBN 0 580 23250 6 Cooperating organizations The European Committee for Stan

3、dardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standard Finland Suomen Standardisoimisliito, r.

4、y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection d

5、u Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation Uni

6、ted Kingdom BritishStandards Institution Amendments issued since publication Amd. No. Date CommentsBSEN665:1995 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 665 3 National annex NA (informative) Committees responsible Inside back

7、 coverBSEN665:1995 ii BSI 01-2000 National foreword This BritishStandard has been prepared by Technical Committee PRI/60, Resilient floor coverings, and is the English language version of EN665:1994 Resilient floor coverings Determination of exudation of plasticizers, published by the European Commi

8、ttee for Standardization (CEN). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary o

9、f pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the

10、 inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 665 November 1994 ICS 91.180 Descriptors: Floor coverings, plasticizers, tests, determination, exudation, macroscopic analysis English version Resilient floor coverings Determination of exudation of plasticizers Revtements de s

11、ol rsilients Dtermination de lexsudation de plastifiants Elastische Bodenbelge Bestimmung der Weichmacherabgabe This European Standard was approved by CEN on1994-11-10. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S

12、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Fren

13、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, F

14、rance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels

15、 1994 Copyright reserved to CEN members Ref. No. EN 665:1994 EEN665:1994 BSI 01-2000 2 Foreword This European Standard was prepared by Technical Committee CEN/TC134, Resilient and textile floor coverings, the Secretariat of which is held by BSI. This European Standard shall be given the status of a

16、national standard, either by publication of an identical text or by endorsement, at the latest by May1995, and conflicting national standards shall be withdrawn at the latest by May1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European S

17、tandard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Principle 3 3 Apparatus and materials 3 4 Sampling and preparation of test pieces

18、 3 5 Conditioning 3 6 Procedure 3 7 Expression of results 3 8 Test report 3EN665:1994 BSI 01-2000 3 1 Scope This European Standard specifies a method for determining the exudation of plasticizers of a polyvinyl chloride floor covering. 2 Principle An absorbent material is placed in contact with the

19、surface of a floor covering, under specified conditions of temperature, pressure and time. This is followed by a visual examination of the absorbent material. 3 Apparatus and materials 3.1 A ventilated oven, capable of being maintained at(80 2) C. 3.2 Absorbent paper, mass per unit area approximatel

20、y15g/m 2 , ash content3%, size of sheets approximately70mm 40mm. NOTECigarette paper without adhesive is suitable for this test. 3.3 A metal plate measuring50mm 25mm 1mm. 3.4 A mass of500g 3.5 A flat, horizontal, metal surface 4 Sampling and preparation of test pieces Take a representative sample fr

21、om the available material. Take six test pieces at equal distances across the sample, the distance between the outer edge of the sample and the nearest edge of the test piece being at least100mm, of minimum dimensions50mm 25mm. 5 Conditioning Condition the test pieces at a temperature of(23 2) C and

22、 relative humidity(50 5)% for a minimum of24h. Maintain these conditions when carrying out the test. 6 Procedure Place the first test piece on the flat surface with its surface layer uppermost. Place a single sheet of absorbent paper on top of it, then place a second test piece on this sheet with it

23、s surface layer downwards, exactly over the first test piece. Arrange a further two pairs of test pieces in the same way on the pile; cover the pile completely with the rigid metal plate and place the500g weight on top. Place the entire combination in the oven which has been pre-heated to80 C. After

24、24h, allow to cool at the ambient temperature and separate the test pieces. Examine the sheets of paper with the naked eye under diffuse lighting to see whether there are any traces of grease or colour. 7 Expression of results Report the presence of any stains and, where applicable, their colour. 8

25、Test report The test report shall contain the following information: a) a reference to this standard, i.e.EN665; b) a complete identification of the product tested, including type, source and manufacturers reference numbers; c) the previous history of the sample; d) the presence, or otherwise of any

26、 stains, and where applicable, their colour; e) any deviation from this standard which may have affected the results.4 blankBSEN665:1995 BSI 01-2000 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted to T

27、echnical Committee PRI/60, Resilient floor coverings, upon which the following bodies were represented: British Adhesives and Sealants Association British Floor Covering Manufacturers Association British Railways Board British Rubber Manufacturers Association Ltd. Consumer Policy Committee of BSI Co

28、ntract Flooring Association Cork Industry Federation Department of the Environment (British Board of Agrment) Department of the Environment (Building Research Establishment) Federation of Plastering and Drywall Contractors Institute of Chartered Arbitrators Royal Institute of British Architects Wood

29、 Panel Products Federation Coopted membersBS EN 665:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incor

30、porated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

31、 finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which

32、ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is

33、BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters S

34、ervice. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts o

35、n the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodi

36、es. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free

37、use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.