BS EN 755-1-2016 Aluminium and aluminium alloys Extruded rod bar tube and profiles Technical conditions for inspection and delivery《铝和铝合金 挤压杆材 棒材、管材和型材 检验和交货技术条件》.pdf

1、BS EN 755-1:2016Aluminium and aluminium alloys Extruded rod/bar, tube and profilesPart 1: Technical conditions for inspection and deliveryBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 755-1:2016 BRITISH STANDARDNational forewordThis British Standard is the UK

2、 implementation of EN 755-1:2016. It supersedes BS EN 755-1:2008 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.Thi

3、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 91002 9 ICS 77.150.10 Compliance with a British Standard cannot confe

4、r immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2016.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 755-1:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 755-1 June 2016

5、 ICS 77.150.10 Supersedes EN 755-1:2008English Version Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery Aluminium et alliages daluminium - Barres, tubes et profils fils - Partie 1 : Conditions techniques de contrle et de

6、livraison Aluminium und Aluminiumlegierungen - Stranggepresste Stangen, Rohre und Profile - Teil 1: Technische Lieferbedingungen This European Standard was approved by CEN on 11 April 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

7、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

8、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

9、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

10、n, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide

11、 for CEN national Members. Ref. No. EN 755-1:2016 EBS EN 755-1:2016EN 755-1:2016 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Ordering information 6 5 Requirements . 8 5.1 Production and manufacturing processes . 8 5.2 Quality control . 8

12、 5.3 Chemical composition limits . 8 5.4 Mechanical properties . 8 5.5 Freedom from surface defects 9 5.6 Tolerances on dimensions and form 9 5.7 Stress corrosion cracking resistance . 9 5.8 Additional requirements 9 6 Test procedures . 9 6.1 Sampling . 9 6.1.1 Samples for chemical analysis 9 6.1.2

13、Specimens for mechanical testing 10 6.1.3 Test pieces for tensile test 11 6.2 Test methods . 11 6.2.1 Chemical composition limits 11 6.2.2 Tensile testing . 11 6.2.3 Brinell hardness testing. 11 6.2.4 Measurement of dimensions 11 6.2.5 Surface finish . 12 6.2.6 Resistance to stress corrosion crackin

14、g 12 6.2.7 Additional tests . 12 6.3 Re-tests 12 6.3.1 Chemical composition limits 12 6.3.2 Mechanical properties 12 6.3.3 Other properties . 13 7 Inspection documents 13 8 Marking of products 13 9 Packaging 13 10 Arbitration 13 Annex A (normative) Location of test pieces 14 A.1 Round, square and he

15、xagonal bar 14 A.1.1 For diameter (D) or width across flats (S) up to and including 40 mm 14 A.1.2 For diameter (D) or width across flats (S) over 40 mm 14 A.2 Rectangular bar 15 A.2.1 For thickness up to and including 12,5 mm 15 BS EN 755-1:2016EN 755-1:2016 (E) 3 A.2.2 For thickness (T) over 12,5

16、mm and up to and including 40 mm . 15 A.2.3 For thickness (T) exceeding 40 mm . 15 A.3 Tube . 16 A.4 Profiles 16 A.4.1 For thickness up to and including 12,5 mm 16 A.4.2 For thickness over 12,5 mm and up to and including 40 mm . 16 A.4.3 For thickness exceeding 40 mm 17 Annex B (normative) Resistanc

17、e to stress-corrosion cracking for alloy EN AW-7075 in tempers T73, T73510 and T73511 Electrical conductivity 18 Bibliography . 19 BS EN 755-1:2016EN 755-1:2016 (E) 4 European foreword This document (EN 755-1:2016) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”,

18、 the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2016, and conflicting national standards shall be withdrawn at the latest by December 2016. Att

19、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 755-1:2008. The following technical modifications have been i

20、ntroduced during the revision: Clause 4, Ordering information, Subclause 5.5, Freedom from surface defects, Subclause 6.3.2, Mechanical properties. EN 755 comprises the following parts under the general title Aluminium and aluminium alloys Extruded rod/bar, tube and profiles: Part 1: Technical condi

21、tions for inspection and delivery; Part 2: Mechanical properties; Part 3: Round bars, tolerances on dimensions and form; Part 4: Square bars, tolerances on dimensions and form; Part 5: Rectangular bars, tolerances on dimensions and form; Part 6: Hexagonal bars, tolerances on dimensions and form; Par

22、t 7: Seamless tubes, tolerances on dimensions and form; Part 8: Porthole tubes, tolerances on dimensions and form; Part 9: Profiles, tolerances on dimensions and form. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impl

23、ement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania

24、, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 755-1:2016EN 755-1:2016 (E) 5 1 Scope This European Standard specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy extruded rod/bar, tube and profile for general e

25、ngineering applications. This European Standard does not apply to: forging stock (EN 603 (all parts), extruded precision profiles in alloys EN AW-6060 and EN AW-6063 (EN 12020 (all parts), products delivered in coils (EN 13957), coiled tubes cut to length (EN 13957). 2 Normative references The follo

26、wing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminiu

27、m and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 755-2, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 2: Mechanical pro

28、perties EN 755-3, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 3: Round bars, tolerances on dimensions and form EN 755-4, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 4: Square bars, tolerances on dimensions and form EN 755-5, Aluminium and alumi

29、nium alloys Extruded rod/bar, tube and profiles Part 5: Rectangular bars, tolerances on dimensions and form EN 755-6, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 6: Hexagonal bars, tolerances on dimensions and form EN 755-7, Aluminium and aluminium alloys Extruded rod/bar

30、, tube and profiles Part 7: Seamless tubes, tolerances on dimensions and form EN 755-8, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 8: Porthole tubes, tolerances on dimensions and form EN 755-9, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 9: Pr

31、ofiles, tolerances on dimensions and form EN 2004-1, Aerospace series Test methods for aluminium and aluminium alloy products Part 1: Determination of electrical conductivity of wrought aluminium alloys BS EN 755-1:2016EN 755-1:2016 (E) 6 EN 10204, Metallic products Types of inspection documents EN

32、12258-1:2012, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 14242, Aluminium and aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis EN 14361, Aluminium and aluminium alloys Chemical analysis Sampling from metal melts EN IS

33、O 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1) EN ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1) ISO 9591, Corrosion of aluminium alloys Determination of resistance to stress corrosion cracking ASTM G47, Sta

34、ndard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:2012 and the following apply. 3.1 order document document or set of document

35、s agreed between supplier and purchaser at the time of ordering 4 Ordering information The order document shall contain the following: a) form and type of product: 1) form of the product (extruded rod/bar, tube or profile). If tube, whether seamless or porthole/bridge extruded, 2) reference to EN 57

36、3-3 for chemical composition limits, 3) reference to EN 515 for temper designation, 4) purchaser application, in particular whether subsequent anodizing is intended. This shall be clearly stated on the order document; b) reference to EN 755-2 for mechanical property limits; c) reference to this docu

37、ment (EN 755-1); d) dimensions and shape of the product: 1) round tube: i) length, BS EN 755-1:2016EN 755-1:2016 (E) 7 and only two of the following dimensions: ii) outside diameter, iii) inside diameter, The tolerances for inside and outside diameter shall state as to whether the proposed tolerance

38、s are mean or inclusive of ovality (ie the maximum allowable deviation at any point from the specified diameter). If this is not made clear on the order, the supplier shall assume that the specified tolerances for either or both outside and inside diameters are inclusive of ovality. However, if the

39、purchaser specifically requires that the outside and/or inside diameter tolerances are to be both mean and inclusive of ovality, then this shall be clearly stated on the order, iv) wall thickness; 2) round bar: i) diameter, ii) length; 3) square and hexagonal bar: i) width across flats, ii) length;

40、4) rectangular bar: i) width, ii) thickness, iii) length; 5) all other cases: i) drawing of cross section, ii) length; e) tolerances on dimensions and form, with reference to the appropriate European Standard and/or a drawing; f) quantity: 1) mass, 2) number of pieces, 3) total length, 4) tolerance

41、on quantity; BS EN 755-1:2016EN 755-1:2016 (E) 8 g) any requirements for inspection documents; h) any special requirements agreed between supplier and purchaser: 1) marking of products, 2) references to drawings, part numbers, etc., 3) additional or special testing, e.g. stress corrosion testing, 4)

42、 surface finish requirements, 5) surface protection, 6) packaging, 7) inspection prior to delivery, 8) use of A50mmvalue instead of A value for elongation; i) for products intended to be anodized by the purchaser, the order document shall also contain the information about the intended particular su

43、rface treatment with reference to the relevant European Standard. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order document, the production and manufacturing processes shall be left to the discretion of the manufacturer. Unless it is explicitly stated

44、 in the order document, no obligation shall be placed on the manufacturer to use the same processes for subsequent similar orders. 5.2 Quality control The supplier shall be responsible for the performance of all inspection and tests required by the relevant European Standard and/or the particular sp

45、ecification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the supplier at the time of placing the order. 5.3 Chemical composition limits The chemical composition limits shall be in conformity with the requirements specifi

46、ed in EN 573-3. If the purchaser requires closer limits for elements than those specified in the above standard, these limits shall be according to an agreement between supplier and purchaser and stated in the order document. 5.4 Mechanical properties The mechanical properties shall be in conformity

47、 with those specified in EN 755-2 or those agreed between supplier and purchaser and stated in the order document. Typical Brinell hardness values are given in EN 755-2, but they are not binding for acceptance purposes. However, a Brinell hardness value may be agreed upon for acceptance testing. BS

48、EN 755-1:2016EN 755-1:2016 (E) 9 5.5 Freedom from surface defects The extruded surface shall be free from defects prejudicial to its suitable and proper use. The product shall have a smooth and clean surface. However, small surface defects such as light scratches, indentations, laminations, discolou

49、ration and non-uniform surface appearance resulting from heat-treatment, etc., which cannot always be totally avoided, are generally permitted on the product surface. Whilst an operation designed to mask a fault is not permitted, the elimination of a superficial fault is permissible provided that the dimensional tolerances and material properties continue to meet the specification. Visible surfaces and surfaces which will be subject to a surface treatment shall be indic