BS EN 764-2-2012 Pressure equipment Quantities symbols and units《压力设备 量值、符号和单位》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 764-2:2012Pressure equipmentPart 2: Quantities, symbols and unitsBS EN 764-2:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 764-

2、2:2012. Itsupersedes BS EN 764-2:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PVE/1, Pressure Vessels.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include a

3、ll the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 71687 4ICS 01.060; 23.020.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This Br

4、itish Standard was published under the authority of theStandards Policy and Strategy Committee on 29 February 2012.Amendments issued since publicationDate Text affectedBS EN 764-2:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 764-2 January 2012 ICS 01.060; 23.020.30 Supersedes EN 764-2:20

5、02English Version Pressure equipment - Part 2: Quantities, symbols and units Equipements sous pression - Partie 2: Grandeurs, symboles et units Druckgerte - Teil 2: Gren, Symbole und Einheiten This European Standard was approved by CEN on 9 December 2011. CEN members are bound to comply with the CEN

6、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cen

7、tre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as th

8、e official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romani

9、a, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means res

10、erved worldwide for CEN national Members. Ref. No. EN 764-2:2012: EBS EN 764-2:2012EN 764-2:2012 (E) 2 Contents page Foreword 3g31g3 Scope 4g32g3 Normative references 4g33g3 General 4g34g3 Quantities, symbols and units 4g3BS EN 764-2:2012EN 764-2:2012 (E) 3 Foreword This document (EN 764-2:2012) has

11、 been prepared by Technical Committee CEN/TC 54 “Unfired pressure vessels”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting nati

12、onal standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes

13、 EN 764-2:2002. This European Standard consists of seven parts which are: Part 1 Terminology Pressure, temperature, volume and nominal size; Part 2 Quantities, symbols and units; Part 3 Definition of parties involved; Part 4 Establishment of technical delivery conditions for metallic materials; Part

14、 5 Compliance and Inspection Documentation of Materials; Part 6 Structure and content of operating instructions; Part 7 Safety systems for unfired pressure equipment. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imple

15、ment this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi

16、tzerland, Turkey and the United Kingdom. BS EN 764-2:2012EN 764-2:2012 (E) 4 1 Scope This European Standard specifies the basic quantities, symbols and units to be used for pressure equipment and assemblies addressed by the European Directive 97/23/EC. 2 Normative references The following referenced

17、 documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references the latest edition of the referenced document (including any amendments) applies. ISO 80000-1, Quantities and units Part 1: General ISO 80000-2, Quantities

18、and units Part 2: Mathematical signs and symbols to be used in the natural sciences and technology ISO 80000-3, Quantities and units Part 3: Space and time ISO 80000-4, Quantities and units Part 4: Mechanics ISO 80000-5, Quantities and units Part 5: Thermodynamics ISO 80000-11, Quantities and units

19、Part 11: Characteristic numbers 3 General 3.1 All units used for pressure equipment shall be derived from the base units of the international system of Units (SI) in accordance with ISO 80000-1, ISO 80000-2, ISO 80000-3, ISO 80000-4, ISO 80000-5, and ISO 80000-11 unless otherwise prescribed in the E

20、uropean Directive 97/23/EC. 3.2 The choice of the appropriate multiple (decimal multiple or sub-multiple) of unit is governed by convenience, the multiple chosen for a particular application being one which would lead to numerical values within a practical range. Therefore when indicating quantities

21、 it is recommended to choose decimal multiple or sub multiple quantities such that the resulting values are easy to handle, e.g. between 0,1 and 1 000. 4 Quantities, symbols and units Symbols and units for the quantities used in pressure equipment shall be in accordance with Tables 1 and 2, otherwis

22、e according to ISO 80000 series for other quantities and in particular ISO 80000-5 for thermodynamic quantities. BS EN 764-2:2012EN 764-2:2012 (E) 5 Table 1 General quantities Quantity Symbol Unit Time t s, min, h Frequency f Hz Dimension any Latin letter bmm Length l mm Thickness e a mm Corrosion a

23、llowance c mm Diameter d, D mm Radius r, R mm Area A, S mm2Volume, capacity V m3 c, dWeight W aN, kN Density kg/m3ePower kW, MW Second moment of area mm4Section modulus Z mm3Acceleration am/s2Plane angle any Greek letter brad, a Symbol differs from the one recommended in ISO 80000.b Symbols may use

24、any lower-case letter, except for those defined elsewhere in this table. cVolume may also be given in L, when required by Pressure Equipment Directive, or in mm3. dLitre “L“ is a non-SI unit which may be used with SI units and their multiples. eDensity may also be given in kg/dm3and kg/mm3.BS EN 764

25、-2:2012EN 764-2:2012 (E) 6 Table 2 Mechanical quantities Quantity bSymbol cUnit Force F N Moment M N.mm Pressure p, P abar d, MPa Temperature T aC Thermodynamic temperature T K Linear expansion coefficient 10-6m/(m*C) Normal stress MPa, N/mm2Shear stress MPa, N/mm2Nominal design stress f MPa, N/mm2T

26、ensile strength RmMPa, N/mm2Tensile strength at 20 C Rm/20MPa, N/mm2Yield strength ReMPa, N/mm2Yield strength at 20 C Re/20MPa, N/mm21,0 % proof strength Rp1,0MPa, N/mm2Proof strength at temperature T Rp/TMPa, N/mm2Upper yield strength ReHMPa, N/mm20,2 % proof strength Rp0,2MPa, N/mm20,2 % proof str

27、ength at temperature T Rp0,2/TMPa, N/mm2Ultimate tensile strength at temperature T Rm/TMPa, N/mm21 % plastic creep strain strength limit at temperature T and time t e, gRcp1/T/t gMPa, N/mm2Creep rupture strength at temperature T and time t eRcm/T/t gMPa, N/mm2Modulus of elasticity E MPa, N/mm2Shear

28、modulus G MPa, N/mm2Poissons ratio - Strain % Elongation after rupture/fracture A % Impact energy KV J Hardness HB h, HV f- Joint coefficient z - Safety factor S - BS EN 764-2:2012EN 764-2:2012 (E) 7 Table 2 (continued) a Symbol differs from the one recommended in ISO 80000.b Quantities without a te

29、mperature index normally refer to room temperature. cSome of these symbols, such as R, f, are not part of ISO 80000.d“bar“ is a non-SI unit which may be used with SI units and their multiples. The unit bar shall be used on nameplates, certificates, drawings, pressure gauges and instrumentation and i

30、s always used as a gauge pressure. This is in line with the requirements of the Pressure Equipment Directive 97/23/EC. 1 bar = 0,1 MPa. eMean value. fThe hardness symbol HV is to be followed by a number (e.g., HV10) indicating the force (in) kg used for testing. gDiffers from present usage in EN 134

31、45:2010, but the intention is to revise EN 13445:2010 accordingly. hThe hardness symbol HB is often followed by a letter (e.g., HBW) indicating the material in the indenter (W would stand for tungsten). NOTE The use of symbols for temperature may be different from the Pressure Equipment Directive 97

32、/23/EC. This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level

33、. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs ar

34、e periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigui

35、ty while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members

36、an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card fr

37、om the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard imple

38、mentation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members

39、are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Sta

40、ndards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or

41、 entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retr

42、ieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: