BS EN 840-2-2012 Mobile waste and recycling containers Containers with 4 wheels with a capacity up to 1300 l with flat lid(s) for trunnion and or comb lifting devices Dimensions an.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 840-2:2012Mobile waste and r e c y c l i n g c o n t a i n e r sPart 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb li

2、fting devices Dimensions and designCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementatio

3、n of EN 840-2:2012. It supersedes BS EN 840-2:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e B / 5 0 8 / 1 , W a s t e c o n t a i n e r s a n d a s s o c i a t e d lifting devices on refuse collection vehicles.A list of organiza

4、tions represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.

5、ISBN 978 0 580 72433 6 ICS 13.030.40 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t

6、e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-2 December 2012 ICS 13.030.40 Supersedes EN 840-2:2004

7、English Version Mobile waste and recycling containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design Conteneurs roulants ordures mnagres et recyclables - Partie 3: Conteneurs 4 roues de capacit infri

8、eure ou gale 1300 l couvercle(s) bomb(s), pour lve-conteneurs par tourillon et/ou peigne - Dimensions et conception Fahrbare Abfall- und Wertstoffbehlter - Teil 2: Behlter mit 4 Rdern und einem Nennvolumen bis 1300 l mit Flachdeckel(n), fr Schttungen mit Zapfenaufnahme und/oder fr Kammschttungen - M

9、ae und Formgebung This European Standard was approved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

10、 bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

11、esponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

12、 Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE

13、NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 840-2:2012: ECopyright European Committee for Standardization Provided by IHS un

14、der license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Volumes 55 Dimensions and design 56 Nominal mass .67 Safety and health requi

15、rements .68 Testing 69 Marking .610 Designation 7Annex A (informative) Recommendations for manufacturers of lifting devices . 15Annex B (informative) A-Deviations . 17Bibliography . 18Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction

16、 or networking permitted without license from IHS-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 3 Foreword This document (EN 840-2:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a nati

17、onal standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig

18、hts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 840-2:2004. Technical changes since the latest edition: The content was adapted to the current state of the art and revised editorially. Figure 3 has been deleted. Frontal

19、 receivers Form B and C have been deleted. Figure 2 has been changed accordingly. This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recycling containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 4

20、00 l for comb lifting devices Dimensions and design; Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices Dimensions and design (the present document); Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s)

21、, for trunnion and/or comb lifting devices Dimensions and design; Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and design; Part 5: Performance requirements and test methods; Part 6: Safety and he

22、alth requirements. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mac

23、edonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS und

24、er license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste containers with 4 wheels, with flat lid(s) and capacity up to 1 300 l

25、to be used by trunnion and/or comb lifting device. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edit

26、ion of the referenced document (including any amendments) applies. EN 840-5, Mobile waste and recycling containers Part 5: Performance requirements and test methods EN 840-6:2012, Mobile waste and recycling containers Part 6: Safety and health requirements EN 1501-1, Refuse collection vehicles Gener

27、al requirements and safety requirements Part 1: Rear loaded refuse collection vehicles EN 1501-5:2011, Refuse collection vehicles General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicles EN ISO 11469, Plastics Generic identification and marking of plastics

28、products (ISO 11469) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in Annex A of EN 840-1:2012. 3.1 mobile waste and recycling container appro

29、priately designed container fitted with wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties containers 3.3 comb lifting device lifting device in which the picking-up system consists of a row of teeth and a locking system to retain the container d

30、uring emptying 3.4 trunnion lifting device lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit the trunnion to retain the container during emptying 3.5 volume total space inside the container when the lid is closed Note 1 to entry: See Tab

31、le 1. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 5 3.6 nominal volume capacity volume stated by the manufacturer Note 1 to entry: See Table

32、 1 without tolerances. Note 2 to entry: The English term “capacity“ and the French term “capacit“ are translated in the German version by the term “Nennvolumen“. 3.7 nominal mass mass, which is calculated as given in Clause 6 3.8 total permissible mass mass of the container plus the nominal mass 3.9

33、 functional and safety dimensions essential dimensions which ensure the functionality and interchangeability of the container with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This part of EN 840 identifies the two classes of containers: Class I

34、 - small size (nominal volume up to 1 000 l); Class II - large size (nominal volume between 1 000 l and 1 300 l). Within the two above-mentioned classes of containers the following volumes are identified: 500 l, 660 l, 770 l, 1 000 l, 1 100 l and 1 200 l. Nominal volumes different from those referen

35、ced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 5 % maximum measured according to EN 840-5. 5 Dimensions and design 5.1 The design of the containers need not correspond to the drawings given in Figure 1. The functional dimensions given in Table 1 sha

36、ll be respected. Recommendations for manufacturers of lifting devices are given in Annex A (see also EN 1501-1). 5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automaticall

37、y locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver, it shall correspond to Figure 2. 5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during the emptying cycle it/they shall be

38、 made with at least two fixing points and have at least one means of opening. 5.4 Handles fitted in front of the trunnion shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1, dimension N 33. The handles and their location also shall be designed so that they

39、 do not damage the operator. 5.5 If the container has ribs in the frontal receiver they shall meet the requirements of Figures 2 and 4. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IH

40、S-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 6 5.6 The container shall have four swivel castors. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities for mounting the castor platine

41、according to at least one of the measurements as shown in Figure 5. 5.7 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.8 The container should have a drain plug. 5.9 When direction locks are fitted they shall be fixed on at least

42、 two castors. 5.10 The container should be fitted with two braked wheels to requirements of EN 840-5. In case of centralised braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralised locking shall be able to be unlocked with a standard

43、 triangular key as shown in Figure 6. The effectiveness of the centralised braking system shall conform to EN 840-5. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm3 x nominal volume. Containers with a nominal volume of more than 1 100 l shall be constr

44、ucted strongly enough to carry a load of 440 kg. 7 Safety and health requirements The container shall meet the safety and health requirements according to EN 840-6. 8 Testing The container shall fulfil the performance requirements and the tests of EN 840-5. 9 Marking 9.1 Each container complying wit

45、h the requirements of this part of EN 840 shall be durably and readably marked on the body in a visible part with: number of this European Standard (EN 840-2); nominal volume; manufacturers name or trademark; total permissible mass, in kilograms; year and month of manufacturing. 9.2 Additional marki

46、ng for quality, recycling, etc. is allowed. Starting five years after the publication of this standard, plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materials is allowed, presuming that all requirements of this standard are complie

47、d with. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 840-2:2012EN 840-2:2012 (E) 7 10 Designation The container complying with the requirements of this European Standard

48、 shall be designated as follows: Container EN 840-2 660 A O 264 Description Standard number Nominal volume, in litres Frontal receiver form: A = frontal receiver 0 = without frontal receiver Lateral receiver: A = trunnions 0 = without lateral receiver Nominal load, in kilograms Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license fro