1、BRITISH STANDARD BS EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product Technical delivery conditions The European Standard EN 10164:2004 has the status of a British Standard ICS 77.140.70 BS EN 10164:2004 This British Standard was published
2、under the authority of the Standards Policy and Strategy Committee on 16 December 2004 BSI 16 December 2004 ISBN 0 580 45118 6 National foreword This British Standard is the official English language version of EN 10164:2004. It supersedes BS EN 10164:1993 which is withdrawn. The UK participation in
3、 its preparation was entrusted to Technical Committee ISE/12, Structural steels, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European public
4、ations referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the nece
5、ssary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the inte
6、rpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and a
7、back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10164 December 2004 ICS 77.140.70 Supersedes EN 10164:1993 English version Stee
8、l products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions Aciers de construction caractristiques de dformation amliores dans le sens perpendiculaire la surface du produit - Conditions techniques de livraison Stahlerzeugnisse mit verbe
9、sserten Verfomungseigenschaften senkrecht zur Erzeugnisoberflche - Technische Lieferbedingungen This European Standard was approved by CEN on 4 November 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th
10、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German
11、). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denma
12、rk, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROP
13、ISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10164:2004: EEN 10164:2004 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative re
14、ferences 5 3 Designation 5 4 Information to be supplied by the purchaser .6 4.1 Mandatory information6 4.2 Options .6 5 Requirements.6 5.1 Reduction of area.6 5.2 Ultrasonic testing.7 6 Inspection .7 6.1 Test units7 6.1.1 General7 6.1.2 Flat products 7 6.1.3 Sections 8 7 Preparation of samples and t
15、est pieces8 7.1 Location and orientation of samples and test pieces8 7.1.1 Preparation of samples .8 7.1.2 Preparation of test pieces.9 7.2 Identification of samples and test pieces .12 8 Test method12 8.1 Tensile test .12 8.2 Retest 13 8.3 Invalidation of tests .13 9 Marking, labelling and packagin
16、g 13 10 Complaints .13 11 Options (see 4.2)13 Bibliography 14 EN 10164:2004 (E) 3 Foreword This document (EN 10164:2004) has been prepared by Technical Committee ECISS/TC 10 “Structural steels Grades and qualities”, the secretariat of which is held by NEN. This European Standard shall be given the s
17、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. This document supersedes EN 10164:1993, Steel products with improved deformation properties perpen
18、dicular to the surface of the product - Technical delivery conditions. During the 5 year review of EN 10164:1993 the members of ECISS/TC 10 agreed to revise EN 10164:1993. It was asked to actualise the normative references and to bring the text in line with “Iron and steel standardization Model for
19、a product standard”. In the scope the product thickness is increased to 400 mm to be in line with EN 10025-2. The upper yield strength is increased to 960 MPa to be in line with EN 10025-6. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standar
20、ds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slov
21、akia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10164:2004 (E) 4 Introduction Flat products and sections of steel as normally manufactured have deformation properties perpendicular to the surface (through thickness) which are different from those obtained in the surface direction.
22、This anisotropy of the properties may lead to difficulties in welded structures, for instance lamellar tearing. It is, however, possible to improve the through thickness properties by using additional steel making procedures. Through thickness properties are characterized in this document by specifi
23、ed values for reduction of area in a through thickness tensile test. There is no direct relationship between these values and the integrity of structures, because the risk of lamellar tearing is also basically influenced by the type of structure, weld design and welding procedure. The minimum values
24、 for reduction of area in this document cannot therefore by themselves be regarded as ensuring safety against occurrence of lamellar tearing. However the reduction of area is a good general guide to lamellar tear resistance i.e. the risk of lamellar tearing decreases with increased reduction of area
25、 in the through thickness tensile test. EN 10164:2004 (E) 5 1 Scope This document specifies through thickness properties and associated test methods for flat products and sections of steel. This document may be applied as a supplement to all product standards for flat products and sections of fully
26、killed steels, except stainless steels. It covers products having a thickness between 15 mm and 400 mm inclusive of steels with a specified minimum upper yield strength R eHor proof strength R p0,2 960 MPa 1)for which improved through thickness properties are required. The application of this docume
27、nt to other product thicknesses and other steel types shall be the subject of agreement at the time of the order. See option 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For
28、undated references, the latest edition of the referenced document (including any amendments) applies. EN 10002-1, Metallic materials - Tensile testing - Part 1: Method of test at ambient temperature EN 10021, General technical delivery requirements for steel and iron products EN 10160, Ultrasonic te
29、sting of steel flat product of thickness equal to or greater than 6 mm (reflection method) EN 10306:2001, Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams 3 Designation Products with requirements for improved deformation properties perpendicular to the surface of th
30、e product shall be designated as follows: the designation of the steel (according to the relevant product standard); the number of this document (EN 10164); the designation of the quality class (according to Table 1). EXAMPLE Steel according to EN 10025-3 of the grade S355N (1.0545) with requirement
31、s for improved deformation properties perpendicular to the surface of the product according to EN 10164 of class Z25, Steel EN 10025-3 - S355N + EN 10164 - Z25 or Steel EN 10025-3 1.0545 + EN 10164 - Z25 1)1 MPa = 1 N/mm 2 . EN 10164:2004 (E) 6 4 Information to be supplied by the purchaser 4.1 Manda
32、tory information The following information shall be supplied by the purchaser at the time of the order: a) the designation of the steel (according to the relevant product standard); b) the designation of the quality class (see Table 1). Where no specific choice is made by the purchaser the supplier
33、shall refer back to the purchaser. 4.2 Options A number of options are specified in Clause 11. In the event that the purchaser does not indicate his wish to implement any of these options, the supplier shall supply in accordance with the basic specification. 5 Requirements 5.1 Reduction of area Tabl
34、e 1 gives minimum values for reduction of area for the specified quality classes. NOTE Reduction of area (Z) is defined in EN 10002-1 as: 100 o u o S S Swhere S o is the original cross-sectional area of the parallel length; S u is the minimum cross-sectional area after fracture. For flat products th
35、e minimum values for reduction of area apply to the whole product. For sections the minimum values for reduction of area apply to either the flange or the web depending on where the samples are taken (see 7.1.1.3). Table 1 Quality classes and minimum values for the reduction of area Reduction of are
36、a in % Quality class Minimum average value of three tests Minimum individual value Z15 15 10 Z25 25 15 Z35 35 25 EN 10164:2004 (E) 7 5.2 Ultrasonic testing Flat products shall be submitted to an ultrasonic examination in accordance with the requirements of EN 10160. Sections shall be submitted to an
37、 ultrasonic examination in accordance with the requirements of EN 10306. Unless otherwise agreed at the time of the order flat products shall meet the requirements of class S1 in accordance with EN 10160, sections shall meet the requirements of class 2.3 in accordance with EN 10306:2001, Table 2. Se
38、e option 2. NOTE Application of the normal ultrasonic techniques does not give information about the susceptibility to lamellar tearing. 6 Inspection 6.1 Test units 6.1.1 General Each consignment shall be subdivided into test units in accordance with 6.1.2 and 6.1.3. 6.1.2 Flat products The test uni
39、ts for flat products of the quality classes Z15, Z25 and Z35 based on the sulphur content of the ladle analysis are given in Table 2. Table 2 Test units for flat products Test unit for S 0,005 % a S 0,005 % aQuality class Parent plate or coil b max. 40 t c Cast d Z15 if agreed x e x Z25 x - x e Z35
40、x - x e a Ladle analysis. b Coil applies to wide strip, narrow strip and slit strip. cOr part thereof of products of the same cast with the same heat treatment. dProducts with the same heat treatment. eUnless otherwise agreed at the time of the order. See option 3 EN 10164:2004 (E) 8 6.1.3 Sections
41、The test unit for sections shall consist of products from the same cast having been subjected to the same heat treatment with a total mass of max. 40 t or part thereof. 7 Preparation of samples and test pieces 7.1 Location and orientation of samples and test pieces 7.1.1 Preparation of samples 7.1.1
42、.1 One sample sufficient to enable six test pieces to be machined shall be taken from each test unit according to 6.1.2. 7.1.1.2 For flat products according to 6.1.2 the sample shall be taken from one end of the product. These samples shall be taken for ingot cast material on the longitudinal axis o
43、f the product and for continuously cast material they may be taken at the manufacturers discretion either on the longitudinal axis of the product or from approximately midway between the edge and the longitudinal axis of the products. 7.1.1.3 For sections the sample shall be taken from one end of th
44、e product. The sampling position shall be the flange unless otherwise agreed at the time of the order. The location of the sample is indicated in Figure 1. See option 4. EN 10164:2004 (E) 9 Key 1 Location of samples Figure 1 Location of samples for sections 7.1.1.4 Only three tensile test pieces sha
45、ll be machined from the sample, the remaining test pieces being kept in reserve in the event that supplementary testing is required (see 8.1.3). 7.1.2 Preparation of test pieces 7.1.2.1 Specimen From the sample obtained in accordance with 7.1, three full thickness specimens shall be taken. The cross
46、- section of each specimen shall be sufficient to permit the removal of any resultant heat affected or work EN 10164:2004 (E) 10 hardened zone during machining of the final test pieces. The balance of the sample shall be kept in reserve in the event that additional tests are required. 7.1.2.2 Test p
47、ieces with or without extension pieces 7.1.2.2.1 General From the specimens obtained in accordance with 7.1.2.1 test pieces with or without extension pieces shall be prepared in accordance with the procedures given in 7.1.2.2.2 and 7.1.2.2.3, as appropriate. Extension pieces are: mandatory for 15 mm
48、 t 20 mm, where t is the product thickness; optional for 20 mm 80 mm, where t is the product thickness. The axis of the test pieces shall be perpendicular to the surface. 7.1.2.2.2 Procedure for test pieces with extension pieces (see Figure 2) Prior to any welding taking place all rust, scale and gr
49、ease shall be removed from the contact surfaces of the specimen. a) Extension pieces are welded to both surfaces of the specimen using friction welding, or another suitable method, in such a way as to ensure a minimum heat affected zone. For specimens from sections with non-parallel surfaces, one surface shall be machined parallel to the other. In the case of I beams with tapered flanges the inside surface shall always be machined. b) The test piece
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1