BS EN 10220-2002 Seamless and welded steel tubes - Dimensions and masses per unit length《无缝和焊接钢管 尺寸和每单位长度的质量》.pdf

1、BRITISH STANDARDBS EN 10220:2002Incorporating corrigendum no. 1Seamless and welded steel tubes Dimensions and masses per unit lengthThe European Standard EN 10220:2002 has the status of a British StandardICS 23.040.10; 77.140.70g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g

2、53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 10220:2002This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority o

3、f the Standards Policy and Strategy Committee on 13 December 2002 BSI 2007ISBN 0 580 40982 1National forewordThis British Standard is the official English language version of EN 10220:2002. It supersedes BS 3600:1997 and DD ENV 10220:1994 which are withdrawn.The UK participation in its preparation w

4、as entrusted to Technical Committee ISE/8, Steel pipes, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible fo

5、r its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK inte

6、rests informed; monitor related international and European developments and promulgate them in the UK.Amendments issued since publicationAmd. No. Date Comments16892 Corrigendum No. 128 February 2007 Revision of supersession details.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10220December 2002

7、ICS 23.040.10; 77.140.70English versionSeamless and welded steel tubes - Dimensions and masses perunit lengthTubes lisses en acier, souds et sans soudure - Tableauxgnraux des dimensions et des masses liniquesNahtlose und geschweite Stahlrohre - AllgemeineTabellen fr Mae und lngenbezogene MasseThis E

8、uropean Standard was approved by CEN on 16 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

9、concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own

10、language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, S

11、weden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2002 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.R

12、ef. No. EN 10220:2002 EEN 10220:2002 (E)2ContentspageForeword31 Scope 42 Normative references 43 Terms and definitions44 Classification of outside diameters .45 Method of calculating masses per unit length56 Dimensions and masses per unit length.5Bibliography 9EN 10220:2002 (E)3ForewordThis document

13、 (EN 10220:2002) has been prepared by Technical Committee ECISS/TC 29, “Steel tubes andfittings for steel tubes“, the Secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the lates

14、t by June 2003, and conflicting national standards shall be withdrawn at the latest byJune 2003.When transforming the European Prestandard ENV 10220 into this European Standard EN 10220, ECISS/TC 29regarded it as necessary to avoid any conflict with and to deviate as little as possible from ISO 4200

15、:1991 becauseof the international trade in steel tubes and tubular products.Table 1 of ENV 10220, which is identical with Table 2 of ISO 4200:1991, was therefore left unchanged forEN 10220.Table 2 of EN 10220 contains dimensions for heavy wall tubes, that are not covered by ISO 4200:1991.All parts o

16、f the European Standard series EN 10305 on steel tubes for precision applications contain tables withpreferred dimensions, that are specific for the various parts of the standards series and the products and fields ofapplication specified therein. Therefore, Table 3 from ENV 10220 with preferred dim

17、ensions for steel tubes forprecision applications has become unnecessary, and has not been included in this standard.This document supersedes ENV 10220:1993.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this E

18、uropean Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.EN 10220:2002 (E)41 ScopeThis European Standard specifies, for seamless and welded

19、 circular steel tubes for general purposes (e. g.mechanical, pressure and structural applications), the following:preferred dimensions for outside diameter and wall thickness in millimetres andmasses per unit length in kilogrammes per metre of plain end tube.Technical Committees of ECISS and CEN sho

20、uld select these preferred dimensions for their product or functionalstandards, where appropriate.The outside diameters are classified into three series reflecting the availability of accessories for piping systems(see Clause 4). This classification of outside diameters into different series and of

21、preferred wall thicknessesindicates the range of steel tubes usually produced.NOTE Information on dimensions for steel tubes for special applications can be found in other EuropeanStandards, e.g. prEN 10255, EN 10305 series, EN ISO 11960 and EN ISO 11961, information on dimensions forstainless steel

22、 tubes in EN ISO 1127.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and publications are listed hereafter. For datedreferences, subsequent amendmen

23、ts to or revisions of any of these publications apply to this European Standardonly when incorporated in it by amendment or revision. For undated references the latest edition of the publicationreferred to applies (including amendments).prEN 10266, Steel tubes, fittings and structural hollow section

24、s Symbols and definition of terms for use in productstandards.3 Terms and definitionsFor the purpose of this European Standard the terms and definitions in prEN 10266 apply.4 Classification of outside diametersThe outside diameters given in Tables 1 and 2 are classified into three series which may b

25、e described in thefollowing way:series 1: outside diameters for which all the accessories needed for the construction of piping systems arestandardized;series 2: outside diameters for which not all accessories are standardized;series 3: outside diameters for which very few standardized accessories e

26、xist.NOTE 1 It is recommended to select, for tubes intended to be used as components of piping systems, outside diameters fromseries 1 in Table 1. Tubes with outside diameters in accordance with series 2 and 3 may not, or not easily, be available.NOTE 2 Accessories for heavy wall tubes with dimensio

27、ns in accordance with Table 2 may not be available regardless of theseries in Table 1 to which the relevant outside diameter is allocated.EN 10220:2002 (E)55 Method of calculating masses per unit lengthThe masses per unit length given in Tables 1 and 2 have been calculated from outside diameter D an

28、d wallthickness T to at least five significant figures, using the formula given below. They have been rounded to threesignificant figures for values of less than 100 and to the nearest whole number for larger values.M = (D - T) T x 0,02466151) kg/mwhereM is the mass per unit length in kg/m,D is the

29、specified outside diameter in mm andT is the specified wall thickness in mm.The calculated values may also be applied to tubes with different density values, but have then to be multiplied bya factor of1,015 for austenitic stainless steel2)0,985 for ferritic and martensitic stainless steel3).NOTE EN

30、 10088-1 provides distinguished density values for various groups of stainless steel grades which may be used forcalculating purposes.6 Dimensions and masses per unit lengthTable 1 gives dimensions consisting of outside diameters D, from 3 series as described in Clause 4, and relatedwall thicknesses

31、 T 65 mm and the calculated masses per unit length of plain end tube.Table 2 gives dimensions consisting of outside diameters D and related wall thicknesses T from 70 mm to 100 mmand the calculated masses per unit length of plain end tube.1) This factor is based on a density of 7,85 kg/dm.2) This fa

32、ctor is based on a density of 7,97 kg/dm.3) This factor is based on a density of 7,73 kg/dm.EN 10220:2002 (E)6Table 1 Dimensions (wall thicknesses T 65 mm) and masses per unit lengthWall thickness T, mmOutside diameterDmmseries0,5 0,6 0,8 1 1,2 1,4 1,6 1,8 2 2,3 2,6 2,9 3,2 3,6 4 4,5 5 5,4 5,6 6,312

33、3 Mass per unit length, kg/m10,2 0,120 0,142 0,185 0,227 0,266 0,304 0,339 0,373 0,404 0,448 0,48712 0,142 0,169 0,221 0,271 0,320 0,366 0,410 0,453 0,493 0,550 0,603 0,651 0,69412,7 0,150 0,179 0,235 0,289 0,340 0,390 0,438 0,484 0,528 0,590 0,648 0,701 0,75013,5 0,160 0,191 0,251 0,308 0,364 0,418

34、 0,470 0,519 0,567 0,636 0,699 0,758 0,813 0,87914 0,166 0,198 0,260 0,321 0,379 0,435 0,489 0,542 0,592 0,664 0,731 0,794 0,852 0,92316 0,191 0,228 0,300 0,370 0,438 0,504 0,568 0,630 0,691 0,777 0,859 0,937 1,01 1,10 1,1817,2 0,206 0,246 0,324 0,400 0,474 0,546 0,616 0,684 0,750 0,845 0,936 1,02 1

35、,10 1,21 1,3 1,4118 0,216 0,257 0,339 0,419 0,497 0,573 0,647 0,719 0,789 0,891 0,987 1,08 1,17 1,28 1,38 1,5019 0,228 0,272 0,359 0,444 0,527 0,608 0,687 0,764 0,838 0,947 1,05 1,15 1,25 1,37 1,48 1,61 1,7320 0,240 0,287 0,379 0,469 0,556 0,642 0,726 0,808 0,888 1,00 1,12 1,22 1,33 1,46 1,58 1,72 1

36、,8521,3 0,256 0,306 0,404 0,501 0,595 0,687 0,777 0,866 0,952 1,08 1,20 1,32 1,43 1,57 1,71 1,86 2,01 2,1222 0,265 0,317 0,418 0,518 0,616 0,711 0,805 0,897 0,996 1,12 1,24 1,37 1,48 1,63 1,78 1,94 2,10 2,2125 0,302 0,361 0,477 0,592 0,704 0,815 0,923 1,03 1,13 1,29 1,44 1,58 1,72 1,90 2,07 2,28 2,4

37、7 2,61 2,68 2,9125,4 0,307 0,367 0,485 0,602 0,716 0,829 0,939 1,05 1,15 1,31 1,46 1,61 1,75 1,94 2,11 2,32 2,52 2,66 2,73 2,9726,9 0,326 0,389 0,515 0,639 0,761 0,880 0,998 1,11 1,23 1,40 1,56 1,72 1,87 2,07 2,26 2,49 2,70 2,86 2,94 3,2030 0,364 0,435 0,576 0,715 0,852 0,987 1,12 1,25 1,38 1,57 1,7

38、6 1,94 2,11 2,34 2,56 2,83 3,08 3,28 3,27 3,6831,8 0,386 0,462 0,612 0,760 0,906 1,05 1,19 1,33 1,47 1,67 1,87 2,07 2,26 2,50 2,74 3,03 3,30 3,52 3,62 3,9632 0,388 0,465 0,616 0,765 0,911 1,06 1,20 1,34 1,48 1,68 1,89 2,08 2,27 2,52 2,76 3,05 3,33 3,54 3,65 3,9933,7 0,409 0,490 0,649 0,806 0,962 1,1

39、2 1,27 1,42 1,56 1,78 1,99 2,20 2,41 2,67 2,93 3,24 3,54 3,77 3,88 4,2635 0,425 0,509 0,675 0,838 1,00 1,16 1,32 1,47 1,63 1,85 2,08 2,30 2,51 2,79 3,06 3,38 3,70 3,94 4,06 4,4638 0,462 0,553 0,734 0,912 1,09 1,26 1,44 1,61 1,78 2,02 2,27 2,51 2,75 3,05 3,35 3,72 4,07 4,34 4,47 4,9340 0,487 0,583 0,

40、773 0,962 1,15 1,33 1,52 1,70 1,87 2,14 2,40 2,65 2,90 3,23 3,55 3,94 4,32 4,61 4,75 5,2442,4 0,517 0,619 0,821 1,02 1,22 1,42 1,61 1,80 1,99 2,27 2,55 2,82 3,09 3,44 3,79 4,21 4,61 4,93 5,08 5,6144,5 0,543 0,650 0,862 1,07 1,28 1,49 1,69 1,90 2,10 2,39 2,69 2,98 3,26 3,63 4,00 4,44 4,87 5,21 5,37 5

41、,9448,3 0,706 0,937 1,17 1,39 1,62 1,84 2,06 2,28 2,61 2,93 3,25 3,56 3,97 4,37 4,86 5,34 5,71 5,90 6,5351 0,746 0,990 1,23 1,47 1,71 1,95 2,18 2,42 2,76 3,10 3,44 3,77 4,21 4,64 5,16 5,67 6,07 6,27 6,9454 0,790 1,05 1,31 1,56 1,82 2,07 2,32 2,56 2,93 3,30 3,65 4,01 4,47 4,93 5,49 6,04 5,47 6,68 7,4

42、157 0,835 1,11 1,38 1,65 1,92 2,19 2,45 2,71 3,10 3,49 3,87 4,25 4,74 5,23 5,83 6,41 6,87 7,10 7,8860,3 0,883 1,17 1,46 1,75 2,03 2,32 2,60 2,88 3,29 3,70 4,11 4,51 5,03 5,55 6,19 6,82 7,31 7,55 8,3963,5 0,931 1,24 1,54 1,84 2,14 2,44 2,74 3,03 3,47 3,90 4,33 4,76 5,32 5,87 6,55 7,21 7,74 8,00 8,897

43、0 1,37 1,70 2,04 2,37 2,70 3,03 3,35 3,84 4,32 4,80 5,27 5,90 6,51 7,27 8,01 8,60 8,89 9,9073 1,42 1,78 2,12 2,47 2,82 3,16 3,50 4,01 4,51 5,01 5,51 6,16 6,81 7,60 8,38 9,00 9,31 10,476,1 1,49 1,85 2,22 2,58 2,94 3,30 3,65 4,19 4,71 5,24 5,75 6,44 7,11 7,95 8,77 9,42 9,74 10,882,5 1,61 2,01 2,41 2,8

44、0 3,19 3,58 3,97 4,55 5,12 5,69 6,26 7,00 7,74 8,66 9,56 10,3 10,6 11,888,9 1,74 2,17 2,60 3,02 3,44 3,87 4,29 4,91 5,53 6,15 6,76 7,57 8,38 9,37 10,3 11,1 11,5 12,8101,6 2,97 3,46 3,95 4,43 4,91 5,63 6,35 7,06 7,77 8,70 9,63 10,8 11,9 12,8 13,3 14,8108 3,16 3,68 4,20 4,71 5,23 6,00 6,76 7,52 8,27 9

45、,27 10,3 11,5 12,7 13,7 14,1 15,8114,3 3,35 3,90 4,45 4,99 5,54 6,35 7,16 7,97 8,77 9,83 10,9 12,2 13,5 14,5 15,0 16,8127 4,95 5,56 6,17 7,07 7,98 8,88 9,77 11,0 12,1 13,6 15,0 16,2 16,8 18,8133 5,18 5,82 6,46 7,41 8,36 9,30 10,2 11,5 12,7 14,3 15,8 17,0 17,6 19,7139,7 5,45 6,12 6,79 7,79 8,79 9,78

46、10,8 12,1 13,4 15,0 16,6 17,9 18,5 20,7141,3 5,51 6,19 6,87 7,88 8,89 9,90 10,9 12,2 13,5 15,2 16,8 18,1 18,7 21,0152,4 5,95 6,69 7,42 8,51 9,61 10,7 11,8 13,2 14,6 16,4 18,2 19,6 20,3 22,7159 6,21 6,98 7,74 8,89 10,0 11,2 12,3 13,8 15,3 17,1 19,0 20,5 21,2 23,7168,3 6,58 7,39 8,20 9,42 10,6 11,8 13

47、,0 14,6 16,2 18,2 20,1 21,7 22,5 25,2177,8 7,81 8,67 9,95 11,2 12,5 13,8 15,5 17,1 19,2 21,3 23,0 23,8 26,6193,7 8,52 9,46 10,9 12,3 13,6 15,0 16,9 18,7 21,0 23,3 25,1 26,0 29,1219,1 9,65 10,7 12,3 13,9 15,5 17,0 19,1 21,2 23,8 26,4 28,5 29,5 33,1244,5 12,0 13,7 15,5 17,3 19,0 21,4 23,7 26,6 29,5 31

48、,8 33,0 37,0273 13,4 15,4 17,3 19,3 21,3 23,9 26,5 29,8 33,0 35,6 36,9 41,4323,9 20,6 23,0 25,3 28,4 31,6 35,4 39,3 42,4 44,0 49,3355,6 22,6 25,2 27,8 31,3 34,7 39,0 43,2 46,6 48,3 54,3406,4 25,9 28,9 31,8 35,8 39,7 44,6 49,5 53,4 55,4 62,2457 35,8 40,3 44,7 50,2 56,7 60,1 62,3 70,0508 39,8 44,8 49,

49、7 55,9 62,0 66,9 69,4 77,9559 43,9 49,3 54,7 61,5 68,3 73,7 76,4 85,9610 47,9 53,8 59,8 67,2 74,6 80,5 83,5 93,8660 64,7 72,7 80,8 87,2 90,4 102711 69,7 78,4 87,1 94,0 97,4 109762 74,8 84,1 93,3 101 104 117813 79,8 89,7 99,6 108 112 125864 84,8 95,4 106 114 119 133914 89,8 101 112 121 125 1411016 99,8 112 125 135 140 1571067 131 141 147 1651118 137 148 154 1731168 143 155 161 1801219 150 162 168 1881321 182 2041422 196 2201524 2361626 252172718291930203221342235233724382540EN 10220:2002 (E)7Table 1 (continued)Wall thickness T, mmOutside diam