BS EN 10244-3-2001 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Aluminium coatings《钢丝及其制品 钢丝上的非有色金属涂层 铝涂层》.pdf

1、BRITISH STANDARD BS EN 10244-3:2001 Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 3: Aluminium coatings The European Standard EN 10244-3:2001 has the status of a British Standard ICS 25.220.40; 77.140.65 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIG

2、HT LAWBS EN 10244-3:2001 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2001 BSI 05-2001 ISBN 0 580 37142 5 National foreword This British Standard is th

3、e official English language version of EN 10244-3:2001. The UK participation in its preparation was entrusted to Technical Committee ISE/26, Steel wire, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-reference

4、s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue

5、. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; p

6、resent to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside fron

7、t cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10244-3 March

8、 2001 ICS 25.220.40 English version Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 3: Aluminium coatings Fils et produits trfils en acier Revtements mtalliques non ferreux sur fils dacier Partie 3: Revtements daluminium Stahldraht und Drahterzeugnisse berzge aus Nichte

9、isenmetall auf Stahldraht Teil 3: berzge aus Aluminium This European Standard was approved by CEN on 21 January 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without a

10、ny alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by

11、translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Irelan

12、d, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any f

13、orm and by any means reserved worldwide for CEN national Members. Ref. No. EN 10244-3:2001 EPage 2 EN 10244-3:2001 BSI 05-2001 Contents Foreword. 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions. 4 4 Requirements relating to coating 4 4.1 Material. 4 4.2 Coating mass. 4 4.3 Appearanc

14、e of coating . 5 4.4 Adherence of the coating. 5 4.5 Special finishes. 5 5 Tests conditions 5 5.1 Samples . 5 5.1.1 General. 5 5.1.2 Length of samples 5 5.2 Determination of mass of coating. 5Page 3 EN 10244-3:2001 BSI 05-2001 Foreword This European Standard has been prepared by Technical Committee

15、ECISS/TC 30, Steel wires, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2001, and conflicting national standards shall be withdrawn at the late

16、st by September 2001. This European Standard for non-ferrous metallic coating on steel wire is made up of the following parts: Part 1: General principles Part 2: Zinc and zinc alloy coatings Part 3: Aluminium coatings Part 4: Tin coatings Part 5: Nickel coatings Part 6: Copper, bronze and brass coat

17、ings According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway

18、, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 4 EN 10244-3:2001 BSI 05-2001 1 Scope This part of this European Standard specifies the requirements for the mass other properties and testing of aluminium coatings on steel wire and steel wire products of circular or other cross-sec

19、tion. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or

20、revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 10244-1, Steel wire and wire products Non-ferrous metallic coating

21、s on steel wire Part 1: General principles ASTM A428, Test method for determining the mass of aluminium coating on steel products 3 Terms and definitions For the purposes of this European Standard the following terms and definitions apply. 3.1 wire with aluminium coating wire to which an aluminium c

22、oating has been applied primarily to protect it against corrosion and/or to improve its electrical conductivity. The coating is generally applied by passing the wires individually through a bath of molten aluminium, by extrusion or by cladding 3.2 mass of coating mass of aluminium per unit area is e

23、xpressed in grams per square meter of stripped wire surface. In the case of thick coatings, the quantity of aluminium on the wire may also be expressed by the radial thickness 4 Requirements relating to coating 4.1 Material The ingot of unrefined aluminium used for the coating shall consist of alumi

24、nium with less than the following impurities: Copper (Cu) 0,10 % max. in mass % Iron (Fe) 0,50 % max. in mass % 4.2 Coating mass The minimum mass of aluminium per unit surface area shall comply with the requirements of Table 1. The product standard relating to wire products with an aluminium coating

25、 may specify different requirements for minimum mass.Page 5 EN 10244-3:2001 BSI 05-2001 4.3 Appearance of coating The aluminium coated wire shall be free of slivers, scale and other imperfections not consistent with good commercial practice. The coating on the wire shall be continuous, reasonably sm

26、ooth and as evenly distributed as practicable. 4.4 Adherence of the coating The aluminium wire shall be tested in accordance with EN 10244-1. The mandrel for the wrapping test shall have a diameter equal to three times the nominal diameter of the wire tested. 4.5 Special finishes If the customer req

27、uires a special finish it shall be specified at the time of enquiry and order. Similarly if drawing after coating with aluminium is requested it shall be specified at the time of enquiry and order. 5 Tests conditions 5.1 Samples 5.1.1 General See the General requirements in EN 10244-1. 5.1.2 Length

28、of samples The length of the samples shall be sufficient to allow the various tests to be carried out. 5.2 Determination of mass of coating The mass of the coating shall be determined using the gravimetric method as indicated in EN 10244-1. The stripping solution, sampling, and other procedures, sha

29、ll be in accordance with ASTM A428. The calculation of the coatings mass is based on the difference in weight in grammes of a test specimen before and after stripping. if m = difference in weight by stripping in grammes; m 2= the weight in grammes of the stripped test sample; d = the diameter of the

30、 (round) wire in mm; m A= the mass of coating in g/m 2 ; 2 1 962 = A m m d mPage 6 EN 10244-3:2001 BSI 05-2001 Table 1 Requirements for the mass of aluminium coating Diameter of wire (mm) d Coating mass Class A amin. Class CE bthickness (g/m 2 ) (mm) 1,2 d 1,5 70 min. 1,5 d 2,0 80 10% 2,0 d 2,3 95 o

31、f nominal 2,3 d 2,7 100 radius 2,7 d 3,7 110 of 3,7 d 6,0 125 wire aClass A normally made by hot dip coating. bClass CE normally used for electrical conductors and normally made by cladding.blankBS EN 10244-3:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the

32、independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure tha

33、t they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible,

34、the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internationa

35、l and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those th

36、at have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services ar

37、e also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details o

38、f these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of

39、 the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission fro

40、m BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.