BS EN 10249-2-1996 Cold formed sheet piling of non alloy steels - Tolerances on shape and dimensions《非合金钢冷成型板桩 第2部分 形状和尺寸公差》.pdf

1、BRITISH STANDARD BS EN 10249-2:1996 Cold formed sheet piling of non alloy steels Part2: Tolerances on shape and dimensions The European Standard EN10249-2:1995 has the status of a BritishStandardBSEN10249-2:1996 This BritishStandard, having been prepared under the directionof the Engineering SectorB

2、oard, was published underthe authority of the Standards Board and comesintoeffect on 15March1996 BSI03-2000 The following BSI references relate to the work on this standard: Committee reference ISE/12 Draft for comment 93/309095 DC ISBN 0 580 24949 2 Committees responsible for this BritishStandard T

3、he preparation of this BritishStandard was entrusted to Technical Committee ISE/12, Structural steels, upon which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork Association Ltd. British Iron and Steel Producers Association British Railways Board Department of Tran

4、sport Institution of Structural Engineers Lloyds Register of Shipping National Association of Steel Stockholders Railway Industry Association Society of Motor Manufacturers and Traders Limited Steel Construction Institute Welding Institute Amendments issued since publication Amd. No. Date CommentsBS

5、EN10249-2:1996 BSI 03-2000 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN10249-2 3 List of references Inside back coverBSEN10249-2:1996 ii BSI 03-2000 National foreword This BritishStandard has been prepared by Technical Committee ISE/12 and is t

6、he English language version of EN10249-2:1995 Cold formed sheet piling of non alloy steels Part2: Tolerances on shape and dimensions, published by the European Committee for Standardization (CEN). A British Standard does not purport to include all the necessary provisions of a contract. Users of Bri

7、tish Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an inside back cover

8、and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN10249-2 June1995 ICS77.140.70 Descriptors: Iron and steel produc

9、ts, metal sections, sheet pilings, steels, unalloyed steels, dimensions, dimensional tolerances, form tolerances English version Cold formed sheet piling of non alloy steels Part2:Tolerances on shape and dimensions Palplanches profiles froid en aciers non allis Partie2: Tolrances sur forme et dimens

10、ions Kaltgeformte Spundbohlen aus unlegierte Sthlen Teil2: Grenzabma“e und Formtoleranzen This European Standard was approved by CEN on1995-05-05. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

11、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

12、 in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece

13、, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of re

14、production and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN10249-2:1995 EEN10249-2:1995 BSI 03-2000 2 Foreword This European Standard was prepared by SC4, Sheet piling, of Technical Committee ECISS/TC10, Structural steels Qualities, the sec

15、retariat of which is held by NNI. EN10249 is composed of two Parts: Part1: Technical delivery conditions; Part2: Tolerances on shape and dimensions. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

16、 December1995, and conflicting national standards shall be withdrawn at the latest by December1995. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,

17、 Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Control of tolerances General 3 4 Height of profiles 3 5 Width of profiles 3 6 Wall thickness of profiles 3 7 Straightness of profiles 3 7.1 Ge

18、neral 3 7.2 Bending 3 7.3 Curving 3 7.4 Twisting 3 8 Length 3 9 Squareness of ends 3 10 Angular deviation 6 11 Mass of profiles 6 12 Joints, overlapping 6 13 Options 6 Figure 1 Measurement of bending 4 Figure 2 Measurement of curving 5 Figure 3 Measurement of twisting 5 Figure 4 Squareness of ends 6

19、 Figure 5 Flange angle ! 6 Table 1 Tolerances on the height of sheet piles 4EN10249-2:1995 BSI 03-2000 3 1 Scope This Part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed non alloy steel sheet piles which are defined in EN102

20、49-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or

21、revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN10051, Continuously hot rolled uncoated plate, sheet and strip of non alloy and alloy stee

22、ls Tolerances on dimensions and shape. EN10249-1, Cold formed sheet piling of non alloy steels Part1: Technical delivery conditions. 3 Control of tolerances General 3.1 All the measurements are taken outside of the zone deformed by cutting at a distance from the ends of at least250mm. 3.2 The dimens

23、ions are measured by instruments of appropriate accuracy. 4 Height of profiles The tolerances on the height of sheet piles are given in Table 1. 5 Width of profiles The tolerances on the width of profiles are as follows: individual sheet pile: 2% of the nominal width; pair of interlocked sheet piles

24、: 3% of the nominal width. 6 Wall thickness of profiles The tolerances on the wall thickness of the profiles shall comply with the requirements of Table2 of EN10051, for a nominal width of strip and sheet over1800mm. 7 Straightness of profiles 7.1 General The controls of the profile straightness (me

25、asurement of bow-heights corresponding to bending and curving) shall be carried out on a pile which freely lies on a plane surface according to the following Figure 1 and Figure 2. For Z-sheet piles, the controls are carried out on an interlocked pair of sheet piles, and if appropriate, on a welded

26、pair of sheet piles when they are delivered welded. 7.2 Bending The bow-height S in the horizontal plane of the sheet pile is the distance between the cord and the arc formed by the sheet pile edge (see Figure 1). The bow-height (S) shall bek 0,25% L. 7.3 Curving The bow-height C in the vertical (pe

27、rpendicular) plane of the sheet pile is the distance between the sheet pile edge in its middle and the reference plane surface (see Figure 2). The bow-height (C) shall bek 0,25% L. 7.4 Twisting One sheet pile end being fixed, the dimension (V) which characterizes the twisting is measured at the free

28、 end of the sheet pile with regard to the reference plane (see Figure 3). The dimension (V) shall not exceed2% L with a maximum of100mm. 8 Length The normal tolerance is 50mm. A reduced tolerance may be agreed at the time of the enquiry and order. Option1, see13.2. 9 Squareness of ends The total dev

29、iation between the highest and the lowest point of the cutting plane (t) shall not exceed2% of the width of the profile, measured perpendicular to the longitudinal axis. When the sheet piles are delivered in seamed pairs by means of welds all along the lock, the upper end shall not present a misalig

30、nment (t) exceeding20mm.EN10249-2:1995 4 BSI 03-2000 Table 1 Tolerances on the height of sheet piles aDimensions in millimetres Designation Figure Nominal dimension Tolerance Height h hk 200 200hk 300 300hk 400 400h 4 6 8 10 a Applicable to the different shapes of cold formed sheet piles, the figure

31、 shows a trench sheet. Figure 1 Measurement of bendingEN10249-2:1995 BSI 03-2000 5 Figure 2 Measurement of curving Figure 3 Measurement of twistingEN10249-2:1995 6 BSI 03-2000 10 Angular deviation For special applications, the tolerance 1)on the flange angle ! (see Figure 5) may be agreed at the tim

32、e of the enquiry and order. Option2, See13.3 11 Mass of profiles Compared with the calculated mass (product of ordered pile length by mass per linear metre of pile according to section tables of the producers), the actual mass may show a deviation of not more than 7% relative to the mass of the tota

33、l delivery. A reduced tolerance may be agreed at the time of the enquiry and order. Option3, see13.4. 12 Joints, overlapping The form of the joints/overlapping is at the manufacturers discretion. If cold formed sheet piles with joints are delivered, the interlocks shall have adequate free play, so t

34、hat the piles can be fitted into each other. This is verified by using two samples500mm long. 13 Options 13.1 Options are available to the purchaser which shall be specified as required at the time of the enquiry and order (see4.2 EN10249-1). 13.2 Option1 A reduced tolerance for the length of profil

35、es (seeclause8). 13.3 Option2 A tolerance for the flange angle ! (see clause10). 13.4 Option3 A reduced tolerance for the mass of profiles (seeclause11). Figure 4 Squareness of ends Figure 5 Flange angle ! 1) This tolerance shall be 3 for piles where smaller leg length isk 10mm (see Figure 5), 2 in

36、the other cases.BSEN10249-2:1996 BSI 03-2000 List of references See national foreword.BS EN 10249-2:1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Eu

37、rope and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produ

38、cts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members a

39、n individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In respon

40、se to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through i

41、ts Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards

42、developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the public

43、ations of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permi

44、ssion from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.