1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58delivered in the semi-processed stateThe European Standard EN 10341:2006 has the status of a Britis
2、h StandardICS 77.140.50Cold rolled electrical non-alloy and alloy steel sheet and strip BRITISH STANDARDBS EN 10341:2006BS EN 10341:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISBN 0 580 48678 8request to its secr
3、etary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalog
4、ue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document com
5、prises a front cover, an inside front cover, the EN title page, pages 2 to 18, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations repres
6、ented on this committee can be obtained on present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National foreword
7、This British Standard is the official English language version of EN 10341:2006. It supersedes BS EN 10126:1996 and BS EN 10165:1996 which are withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/NFE/5, Magnetic alloys and steels, which has the responsibility to
8、: aid enquirers to understand the text;EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10341May 2006ICS 77.140.50 Supersedes EN 10126:1995, EN 10165:1995 English VersionCold rolled electrical non-alloy and alloy steel sheet and stripdelivered in the semi-processed stateBandes et tles magntiques la
9、mines froid en acier nonalli et en acier alli livres ltat semi-finiKaltgewalztes Elektroblech und -band aus unlegierten undlegierten Sthlen im nicht schlussgeglhten ZustandThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regula
10、tions which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This Europe
11、an Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national
12、standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EU
13、ROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10341:2006: E2 Contents Page
14、Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Classification and designation.6 4.1 Classification6 4.2 Designation 6 5 Information to be supplied by the purchaser .7 5.1 Mandatory information7 5.2 Options .7 6 General requirements8 6.1 Production process .
15、8 6.2 Form of supply.8 6.3 Delivery condition8 6.4 Surface condition.8 6.5 Suitability for cutting.9 7 Technical requirements 9 7.1 Magnetic properties.9 7.2 Geometrical characteristics and tolerances 11 7.3 Other properties 12 8 Inspection and testing 13 8.1 General. 13 8.2 Sampling 13 8.3 Preparat
16、ion of test specimens 13 8.4 Test methods. 14 8.5 Retests . 14 9 Marking, labelling and packing . 15 10 Complaints 15 Annex A (informative) Maximum specific total loss at 1,0 T 16 Annex B (informative) Density determination . 17 Bibliography. 18 EN 10341:20063 Foreword This document (EN 10341:2006)
17、has been prepared by Technical Committee ECISS/TC 24 “Electrical steel sheet and strip qualities - Qualities, dimensions, tolerances and specific tests”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an iden
18、tical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. This document supersedes EN 10126:1995 and EN 10165:1995. This document is based on IEC 60404-8-3:2005 which was technically changed. According to the C
19、EN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour
20、g, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10341:20064 Introduction This document has been prepared by merging EN 10126:1995 and EN 10165:1995, taking into consideration corresponding decisions of IEC/TC 68 on relev
21、ant IEC documents IEC 60404-8-2:1998 and IEC 60404-8 -3:1998 which are being merged at the same time. The merged document published as IEC 60404-8-3:2005 was the basis of this European Standard. The intention of this merging was to specify no longer non-alloy and alloy steel grades for cold rolled e
22、lectrical steel sheet and strip, but to leave the type of steel open. Therefore, it has been decided to use a new letter “K“ instead of previous used “D“ or “E“ for the designation of electrical steels specified in this European Standard. The dew point of the gas used for the heat treatment specifie
23、d in 7.1.1 is + 20 C 2 C at atmospheric pressure. This is the value stated in EN 10165:1995 but it differs from the temperature of + 35 C stated in EN 10126:1995. As the final annealing of cold-rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state is the r
24、esponsibility of the purchaser, attention is drawn to the importance of this treatment for the properties of the material. For this reason the magnetic properties in Table 1 are given for a reference condition (see 7.1.1) obtained by a suitable heat treatment. To ensure that the properties in use ar
25、e equivalent to those specified, it is important that the heat treatment carried out by the user is equivalent to that used to define the reference condition. It is recognized that these materials may be used in the semi-processed state, in which case the magnetic properties are not subject to the s
26、pecifications of this standard. EN 10341:20065 1 Scope This document specifies cold-rolled electrical non-oriented non-alloy1)or alloy2)steel sheet and strip delivered in nominal thicknesses of 0,50 mm and 0,65 mm in the semi-processed condition, that is without final heat treatment; in particular,
27、it specifies general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as the inspection procedure. This document applies to material intended for the construction of magnetic circuits. These magnetic materials correspond respectiv
28、ely to subclauses C21 and B2 of IEC 60404-1:2000. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a
29、ny amendments) applies. EN 10021, General technical delivery requirements for steel and iron products EN 10027-1, Designation systems for steel Part 1: Steel names EN 10027-2, Designation systems for steel Part 2: Numerical system EN 10204, Metallic products Types of inspection documents EN 10251, M
30、agnetic materials - Methods of determination of the geometrical characteristics of electrical steel sheet and strip EN 60404-2, Magnetic materials Part 2: Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame (IEC 60404-2:1996) IEC 60050-1
31、21:1998, International Electrotechnical Vocabulary Part 121: Electromagnetism IEC 60050-221:1990, International Electrotechnical Vocabulary Part 221: Magnetic materials and components IEC 60404-1:2000, Magnetic materials Part 1 : Classification IEC 60404-13, Magnetic materials Part 13 : Methods of m
32、easurement of density, resistivity and stacking factor of electrical steel sheet and strip 3 Terms and definitions For the purposes of this document, the definitions of the principal terms relating to magnetic properties given in IEC 60050-121:1998 and IEC 60050-221:1990 apply. In addition, the foll
33、owing terms and definitions apply. 1) Non-alloy steel is that steel the basic constituent of which is iron containing alloying elements in amounts smaller than the limiting values fixed by EN 10020. 2) Alloy steel is that steel the basic constituent of which is iron containing alloying elements in a
34、mounts equal to or greater than the limiting values fixed by EN 10020. EN 10341:20066 3.1 edge camber greatest distance between a longitudinal edge of the sheet or strip and the line joining the two extremities of the measured length of this edge 3.2 flatness property of a sheet or a length of strip
35、 which is characterized by the wave factor, i.e. the relation of the height of the wave to its length 3.3 residual curvature permanent curvature in the direction of rolling of an unwound strip 3.4 internal stresses stresses which are characterized by a deviation in relation to the line of cutting 4
36、Classification and designation 4.1 Classification The steel grades covered by this document are classified according to the specified value of maximum specific total loss in watts per kilogram at 1,5 T after a reference heat treatment (see 7.1.1) and according to the nominal thickness of the materia
37、l (0,50 mm, 0,65 mm). 4.2 Designation 4.2.1 For the steel grades covered by this document, the steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. The steel name comprises the following in the order given: 1) the letter M for electr
38、ical steel; 2) one hundred times the specified value of maximum specific total loss at 50 Hz, in watts per kilogram, corresponding to the nominal product thickness, at 1,5 T; 3) one hundred times the nominal thickness of the material, in millimetres; 4) the letter K for non-alloy or alloy electrical
39、 steel sheet or strip delivered in the semi-processed state. EXAMPLE M660-50K for electrical non-alloy or alloy steel sheet or strip with a specified maximum specific total loss at 1,5 T of 6,60 W/kg at 50 Hz and a nominal thickness of 0,50 mm, supplied in a semi-processed state. EN 10341:20067 5 In
40、formation to be supplied by the purchaser 5.1 Mandatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) quantity; b) type of product (strip or sheet); c) number of this European Standard (EN 10341); d) steel name or number (see 4.2.1); e)
41、 dimensions of sheets or strips required (including any limitations on the external diameter of a coil) (see 6.2 and 7.2.2); f) limitations on the mass of a bundle of sheets or of a coil (see 6.2); g) type of inspection document when specific inspection is specified (see 8.1). 5.2 Options A number o
42、f options are specified in this standard and listed below. lf the purchaser does not indicate his wish to implement one of these options, the products shall be supplied in accordance with the basis specification of this standard (see 5.1). 1) permissibility of welds and its marking (see 6.2); 2) sur
43、face condition (see 6.4); 3) suitability test for punching and cutting (see 6.5); 4) conventional density (see Table 1, footnote c); 5) anisotropy of loss and magnetic polarization (see 7.1.4); 6) thickness difference perpendicular to the direction of rolling for narrow strips and its measurement (s
44、ee 7.2.1 and 8.4.3.1); 7) width tolerances for nominal widths 1 250 mm (see Table 2, footnote a); 8) density values deviating from those given in Table 1 (see 7.3.1); 9) stacking factor (see 7.3.2); 10) acceptance unit other than 20 t (see 8.1); 11) test temperature other than (23 5) C (see 8.4.1);
45、12) marking of the products (see Clause 9). EN 10341:20068 6 General requirements 6.1 Production process The production process of the steel and its chemical composition are left to the discretion of the manufacturer. 6.2 Form of supply The material is supplied in bundles in the case of sheets and i
46、n coils in the case of strip. The mass of bundles of sheets or coils shall be agreed at the time of enquiry and order. The most usual values for internal diameter of coils are approximately 508 mm and 610 mm. The recommended value is approximately 508 mm. The external diameter shall be the subject o
47、f an agreement at the time of enquiry and order. Sheets which make up each bundle shall be stacked so that the side faces are substantially flat and approximately perpendicular to the top face. Strip shall be of constant width and wound in such a manner that the edges are superimposed in a regular m
48、anner and that the side faces of the coil are substantially flat. Coils shall be sufficiently tightly wound that they do not collapse under their own weight. Strip may exhibit welds resulting from the removal of defective zones if agreed at the time of enquiry and order. If necessary, the marking of
49、 welds may be agreed at the time of enquiry and order. For coils containing repair welds, each part of the strip shall be of the same grade. The edges of parts welded together shall not be so much out of alignment as to affect the further processing of the material. 6.3 Delivery condition Material supplied with trimmed edges shall not have any burrs which will adversely affect its further application or use. As the result of the method of manufacture and delivery in the form of coils, material may, in
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1