BS EN 114001-1984 Harmonized system of quality assessment for electronic components - Blank detail specification photomultiplier tubes《电子元器件质量保证协调体系 空白详细规范 充气管》.pdf

1、BRITISH STANDARD BS EN 114001:1997 Incorporating Amendment No. 1 to BS CECC 14001:1984 (renumbers BS as BSEN 114001:1997) Harmonized system of quality assessment for electronic components Blank detail specification: Photomultiplier tubes The European Standard EN114001:1991 has the status of a Britis

2、h Standard ICS 31.100BSEN114001:1997 BSI 04-2000 ISBN 0 580 34756 7 National foreword This British Standard has been prepared by Technical Committee EPL/39 and is the English language version of EN114001:1991 Harmonized system of quality assessment for electronic components Blank detail specificatio

3、n: Photomultiplier tubes, published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Stan

4、dards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for

5、 their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 8 and a back cover. This standard has been updated (se

6、e copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN114001:1997 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 114001

7、 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 114001 December 1991 UDC: Descriptors: Quality, electronic components, tubes English version Blank Detail Specification: Photomultiplier tubes Spcification Particulire Cadre: Tubesphotomultiplicateurs Vordruck fr Bauartspezifikation: Ein

8、edeutsche Version liegt zur Zeit nicht vor * This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on20November1991. The text of this standard consists of the text of CECC14001 Issue11984 of the corresponding CECC Specification. CENELEC members are bound to comply

9、 with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the General Secretari

10、at of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German * ). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CECC General Secretariat has the

11、same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United Kingdom. The membership of the

12、 CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue

13、 de Stassart 35, B-1050 Brussels 1991 Copyright reserved to CENELEC members Ref. No. EN 114001:1991 EEN114001:1991 BSI 04-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries ofthe European Committee for Electrotechnical Standardization (CENELEC) w

14、ho wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications andquality assessment procedures for electronic components, and by the grant of an internationally recog

15、nized Mark, or Certificate, of Conformity. The components produced under the System are thereby accepted by all member countries without further testing. This specification has been formally approved bytheCECC, and has been prepared for those countries taking part in the System who wish toissue nati

16、onal harmonized specifications for PHOTOMULTIPLIER TUBES. It should be read inconjunction with document CECC00100: BasicRules (1974). At the date of printing of this document the membercountries of the CECC are Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, the Netherlands, Nor

17、way, Portugal,Spain, Sweden, Switzerland, and theUnited Kingdom. Preface This blank detail specification was prepared by CECC Working Group11: “Electro-optical devices”. It is a blank detail specification for photomultiplier tubes relating to the generic specification CECC14000. The text of this spe

18、cification was circulated to the CECC for voting in the document indicated below and was ratified by the President of the CECC for printing as a CECC Specification: It is recognized that the layout proposed cannot be applied to all detail specifications based on this document. The CECC Management Co

19、mmittee at its meeting in Copenhagen in March1979 decided that as the German National Authorized Institution would not be implementing the requirements of this CECC specification, the text should be published in the English and French versions only. Contents Page Foreword 2 Data 4 Limiting values 4

20、Operating conditions and typical characteristics 5 Marking 5 Ordering information 5 Related documents 5 Structural similarity 5 X-radiation 5 Additional information 5 Test conditions and inspection requirements 5 Document Voting Date Report on the Voting CECC(Secretariat) 994 June 1981 CECC(Secretar

21、iat) 1078EN114001:1991 BSI 04-2000 3 Key for page 4 The numbers between square brackets on page4 correspond to the following indications which should be given: Identification of the detail specification 1 The name of the National Standards Organization under whose authority the detail specification

22、ispublished, and, if applicable, the organization from whom the detail specification is available 2 The CECC Symbol and the number allotted to the detail specification by the CECC General Secretariat 3 The number and issue number of the CECC generic or sectional specification as relevant; also natio

23、nal reference if different 4 If different from the CECC number the national number of the detail specification, date of issue and anyfurther information required by the national system, together with any amendment numbers. Identification of the component 5 A short description of the type of componen

24、t 6 Information on typical construction (where applicable) For 5 and 6 the text to be given in the detail specification should be suitable for an entry in CECC00200 (QPL) and CECC00300 (Library List). 7 Outline drawing and/or reference to the relevant document for outlines 8 Application or group of

25、applications covered (seeNote below) 9 Reference data on the most important properties, to allow comparison between the various component types NOTEWhen a device is so designed that it can satisfy several applications, this should be stated in the detail specification, inwhichcase the characteristic

26、s and inspection requirements relevant to these applications should be met simultaneously (thesemayappear in different columns of a detail specification or in different detail specifications, as the case may be).EN114001:1991 4 BSI 04-2000 1 Page: of CECC 14001-XXX 2 ELECTRONIC COMPONENT OF ASSESSED

27、 QUALITY IN ACCORDANCE WITH 3 4 DETAIL SPECIFICATION FOR: PHOTOMULTIPLIER TUBES 5 DESCRIPTION and CONSTRUCTION Photocathode type, and window material Dimensions of photocathode window Number of stages, dynode geometry and type. 6 OUTLINE DRAWING (Not for inspection purposes) 7 8 Overall length; Base

28、 Reference to IEC67 or REFERENCE TO THE INSPECTION DRAWING APPLICATIONS LEVEL OF QUALITY ASSESSMENT DATA (Not for inspection purposes) 9 Mechanical Mounting position and accessories Mass Environmental (where applicable) LIMITING VALUES (Absolute maximum rating system IEC134) Min. Max.Unit Overall vo

29、ltage (subject to not exceeding the rated anodeluminoussensitivity) a V Cathode to first dynode voltage a V Anode to last dynode voltage a V Voltage between successive dynodes a V Anode sensitivity a A/1m or A/W Anode current (mean) a mA Information about manufacturers who have components qualified

30、to this detail specification is available in the current CECC00200: Qualified Products List. a Denotes that a value shall be inserted in the detail specification.EN114001:1991 BSI 04-2000 5 The characteristics listed are examples only, the specification writer shall include those characteristics whi

31、ch are relevant to the tube operation. MARKING ORDERING INFORMATION RELATED DOCUMENTS STRUCTURAL SIMILARITY X-RADIATION ADDITIONAL INFORMATION recommended precautions. spectral/characteristic curves TEST CONDITIONS AND INSPECTION REQUIREMENTS These are given in the following tables. The test conditi

32、ons to be used shall be specified in the detail specification as required for a given type, in line with the requirements given in CECC14000 for the relevant test. ALL REFERENCES TO CLAUSE NUMBERS ARE MADE WITH RESPECT TO CECC14000 UNLESS OTHERWISE STATED. If the detail specification includes additi

33、onal tests which are destructive, these shall be marked (D). General test conditions All potentials are defined with respect to 1)unless otherwise stated. LIMITING VALUES (Contd.) Min. Max. Unit Anode power dissipation a W Cathode current a 4A Storage temperature of specified duration a a C Operatin

34、g temperature of specified duration (ambient) a a C The data and descriptions listed are examples only; the specification writer shall include data relevant to the tube application. OPERATING CONDITIONS AND TYPICAL CHARACTERISTICS (Specification writer to select from the following as required by the

35、 tube design). When the tube is operated under the conditions given below, the characteristic values which follow themare attainable: Electrode voltages or dynode chain with total voltage a Anode sensitivity a Min. Max. Unit Cathode sensitivity 4A/1m or mA/W Transit time a ns Capacitance, anode to a

36、ll dynodes a pF Anode dark current a nA Anode pulse rise time a ns a Indicates that a value/or values shall be inserted in the detail specification. 1) To be completed in the detail specification.EN114001:1991 6 BSI 04-2000 The specification shall include the following tests unless precluded by the

37、tube design. All tests are non-destructive GROUP A Lot by lot Defects do not cause lot rejection Examination or Test Ref Conditions of test Inspection requirements Limits Levels Min. Max. Unit IL AQL Subgroup A1 100% Visual inspection 4.3 See 4.3 Cathode sensitivity 4.5.1 or 4.5.4 + 4A/1m or mA/W An

38、ode sensitivity 4.5.2 or 4.5.6 + A/1m or A/W Anode dark current 4.5.13 + nA Only tests marked (D) are destructive GROUP B Lot by Lot AQL: given in% Examination or Test Ref Conditions of test Inspection requirements Limits Levels IL AQL Subgroup B1 S-4 4,0 Dimensions, major 4.4 See inspection drawing

39、 GROUP C NOTAPPLICABLE + To be given in the detail specificationEN114001:1991 BSI 04-2000 7 Only tests marked (D) are destructive GROUP D QUALIFICATIONAPPROVAL + To be given in the detail specification The sample size and acceptancecriterion shall be as3.4 ofCECC14000 Examination or Test Ref. Condit

40、ions of test Inspection requirements Limits Min. Max. Unit Dimensions, detail 4.4 See inspection drawing Inter-electrode insulation 4.5.15 + nA Capacitance 2.2 IEC 100 + pF Operating endurance (D) 4.8.2 Post endurance tests: a Cathode sensitivity Anode sensitivity Anode dark current a The limits may

41、 be the Group A limits, wider or in terms of a permitted change from the original value at the discretion of the specification writer.EN114001:1991 8 BSI 04-2000 Appendix to detail specification Each detail specification shall include an appendix containing the following: Inspection drawing showing

42、the dimensions to be inspected under each subgroup.blankBS EN 114001:1997 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international l

43、evel. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be g

44、rateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service c

45、alled PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international

46、standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical He

47、lp to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substa

48、ntial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international sta

49、ndardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for an