BS EN 12032-1997 Self-adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing《自粘胶带 热固化处理时胶带粘性测量》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12032 : 1997 The Eu

2、ropean Standard EN 12032 : 1996 has the status of a British Standard ICS 83.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Self-adhesive tapes Measurement of bonding of thermosetting adhesive tapes during curingBS EN 12032 : 1997 This British Standard, having been prepare

3、d under the direction of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 February 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference PKW/3 Draft for comment 92/42638

4、 DC ISBN 0 580 26727 X Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PKW/3, Distribution packaging, transport packaging and unit loads, upon which the foll

5、owing bodies were represented: British Adhesives and Sealants Association British Apparel and Textile Confederation British Coatings Federation Ltd. British Fibreboard Packaging Association British Glass Manufacturers Confederation British Industrial Truck Association British Plastics Federation Bri

6、tish Retail Consortium British Rubber Manufacturers Association Ltd. British Tensional Strapping Association Ltd. British Timber Merchants Association British Wood Preserving and Damp-proofing Association Chamber of Shipping Chemical Industries Association China Clay Association Cranfield Logistics

7、Department of Transport Engineering Equipment and Materials Users Association Federation of the Electronics Industry Flexible IBC Association Food and Drink Federation Independent Pallet Repair Committee Institute of Grocery Distribution Metal Packaging Manufacturers Association Ministry of Defence

8、National Association of Pallet Distributors Power Fastenings Association Pira International Road Haulage Association Ltd. Society of Occupational Medicine Storage Equipment Manufacturers Association Timber Packaging and Pallet Confederation Timber Research and Development Association United Kingdom

9、Softwood Sawmillers Association The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Adhesive Tape Manufacturers Association British Footwear Manufacturers Federation British Steel Industry (Wire Section) Packaging Distributors Association Pre

10、ssure Sensitive Manufacturers AssociationBS EN 12032 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 12032 3ii BSI 1997 BS EN 12032 : 1997 National foreword This British Standard has been prepared by Technical Committee PKW/3 and i

11、s the English language version of EN 12032 : 1996 Self-adhesive tapes Measurement of bonding of thermosetting adhesive tapes during curing, published by the European Committee for Standardization (CEN). Compliance with a British Standard does not of itself confer immunity from legal obligations. Sum

12、mary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue

13、de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 12032 : 1996 E EUROPEAN STANDARD EN 12032 NORME EUROPE ENNE EUROPA ISCHE NORM May 1996 ICS 83.180 Descriptors: Adhesive tapes, thermosetting resins, tests, properties, cross-linking English version Self-adhesive tapes

14、 Measurement of bonding of thermosetting adhesive tapes during curing Rubans auto-adhe sifs Mesure de la liaison des rubans thermodurcissables pendant le traitement thermique Klebeba nder Messung der Bindefestigkeit von wa rmeha rtenden Klebeba ndern wa hrend der Vernetzung This European Standard wa

15、s approved by CEN on 1996-04-19. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation

16、al standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti

17、fied to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdo

18、m.Page 2 EN 12032 : 1996 BSI 1997 Foreword This European Standard has been prepared by the Technical Committee CEN/TC 253, Self-adhesive tapes, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical te

19、xt or by endorsement, at the latest by November 1996, and conflicting national standards shall be withdrawn at the latest by November 1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard

20、: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Definition 3 3 Principle 3 4 Apparatus 3 5 Test samples and test pieces 3 6 Proce

21、dure 3 7 Expression of results 5 8 Test report 5Page 3 EN 12032 : 1996 BSI 1997 First piece of adhesive tape Dimensions in millimetres Figure 1. Step 1 1 Scope This standard specifies a method to observe the bonding of a thermosetting adhesive tape during the thermosetting process. The temperature a

22、nd duration for each test shall be as the manufacturers instructions for bonding the relevant adhesive tape. 2 Definition For the purposes of this standard, the following definition applies. thermosetting adhesive Adhesive which becomes firmer on heating and remains so on cooling, and remains set re

23、gardless of subsequent temperature cycles. 3 Principle A piece of adhesive tape to be tested is applied overlapping the back of a second piece of the same adhesive tape. This assembly is loaded with a weight, then suspended vertically in an oven, where it is cured under the specified temperature and

24、 time conditions. 4 Apparatus 4.1 Oven with air circulation. 4.2 Polished cylindrical metal roller with a diameter of at least 50 mm and a mass corresponding to 2 kg per centimetre width of adhesive tape under test. 4.3 Polished metal plate, approximate dimensions 600 mm 3 200 mm3 5 mm, with a guide

25、 mark parallel to one of the short sides and at a distance of 12 mm from it. 4.4 50 g masses. 5 Test samples and test pieces Condition three sample rolls (at least 12 mm wide) for 24 h at 23 C 2 C and 50 % 5 % relative humidity. Discard the three outer turns of adhesive tape from each roll. Take two

26、 test pieces approximately 150 mm long from each sample roll. 6 Procedure 6.1 Preparation of test pieces A test piece of adhesive tape taken from one of the sample rolls is applied with its adhesive surface on the back of a second test piece taken from the same roll, so that the length of the contac

27、t area measures 12 mm 0,8 mm. 6.1.1 Step 1 (figure 1) To carry out this operation, the first test piece of adhesive tape is applied to the polished steel plate, at roughly the centre of this plate, so that the adhesive tape extends about 50 mm beyond the guide mark. Carefully cut the adhesive tape w

28、ith a razor blade along the short side of the plate nearest the guide mark.Page 4 EN 12032 : 1996 BSI 1997 Second piece of adhesive tape Dimensions in millimetres Figure 2. Step 2 Cut the second piece at 12 mm from the short side of the plate Dimensions in millimetres Figure 3. Step 3 6.1.2 Step 2 (

29、figure 2) Apply the second test piece of adhesive tape on top of the first test piece, as accurately as possible, and along a length of approximately 50 mm from the side of the plate nearest the guide mark. Pass the metal roller twice, in each direction, over the contact area, at a speed of approxim

30、ately 10 mm/s. Placing the metal plate at an angle and avoiding any pressure, position a razor blade on the back of the second adhesive tape, aligning it with the guide mark made on the polished metal plate. The topmost test piece of adhesive tape is gradually unpeeled and torn against the razor bla

31、de, thus defining a contact area of the adhesive tapes measuring 12 mm 0,8 mm.Page 5 EN 12032 : 1996 BSI 1997 Cut to 12 mm width Fold back the free ends Dimensions in millimetres Figure 4. Step 3 6.1.3 Step 3 (figure 3 and figure 4) The lower test piece of adhesive tape which is still attached to th

32、e metal plate is then unpeeled, starting at the uncut end (figure 3). Trim lengthwise the test pieces prepared in this way and measuring more than 12 mm wide, to a width of 12 mm 0,8 mm, using a razor blade. It would then be appropriate to fold back the free ends of the test pieces over a length of

33、approximately 50 mm, adhesive sides together (figure 4). 6.2 Test procedure Suspend the three test pieces vertically in an oven, each loaded with a 50 g mass, at their lower ends. They remain thus for the period and at the temperature indicated in the adhesive tape manufacturers instructions for the

34、 curing process. 7 Expression of results Record if separation of the adhesive joint occurs. A separation of the joint will have occurred if the weight has fallen or if the adhesive tape has slipped more than 2 mm. 8 Test report The test report shall include the following information: a) a reference

35、to this European Standard; b) all information necessary to identify the test sample; c) test conditions; d) the date of the test; e) the results obtained; f) any operation not specified in this European Standard which may influence the results.BSI 389 Chiswick High Road London W4 4AL | | | | | | | |

36、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent nati

37、onal body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess t

38、he latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of

39、which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign st

40、andards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information

41、on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

42、ormation Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax

43、: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval s

44、ystem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If

45、 these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.