1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12115:2011Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals SpecificationBS EN 12115:2011 BRITISH STANDARDNational forewordThis British St
2、andard is the UK implementation of EN 12115:2011. Itsupersedes BS EN 12115:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can beobta
3、ined on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 56538 0ICS 23.040.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This B
4、ritish Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2011.Amendments issued since publicationDate Text affectedBS EN 12115:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12115 January 2011 ICS 23.040.70 Supersedes EN 12115:1999Englis
5、h Version Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification Tuyaux et assemblages flexibles en caoutchouc et en matriaux thermoplastiques pour substances chimiques liquides ou gazeuses - Spcifications Gummi- und Kunststoffschluche und -schlauchleitun
6、gen fr flssige oder gasfrmige Chemikalien - AnforderungenThis European Standard was approved by CEN on 30 November 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
7、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other la
8、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denm
9、ark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISA
10、TION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12115:2011: EBS EN 12115:2011EN 12115:2011 (E) 2 Contents Page Foreword 4Introduction .51
11、 Scope 62 Normative references 73 Terms and definitions .74 Classification 85 Couplings and end fittings .86 Materials and construction .86.1 General 86.2 Lining 86.3 Cover .86.4 Reinforcement 86.5 Helical wires .97 Dimensions and tolerances, typical masses 97.1 Diameters, thickness, vacuum stabilit
12、y, bend radii and resistance to vacuum 97.2 Concentricity . 107.3 Length of hose assemblies 108 Physical properties of materials used for hoses . 108.1 General . 108.2 Materials used for the lining 118.3 Material of the helix 128.4 Materials of the end fittings and couplings . 129 Performance requir
13、ements of hoses and hose assemblies . 1210 Electrical properties . 1411 Frequency of testing 1512 Type tests 1513 Test report . 1514 Marking 1514.1 Hoses . 1514.2 Hose fittings 1614.3 Identification of hose assemblies . 1615 Storage and admissible storage time . 17Annex A (normative) Test frequency
14、for type tests and routine tests . 18Annex B (informative) Production acceptance tests 19Annex C (informative) Couplings and fittings . 20Annex D (normative) Crush recovery test (for SD hoses only) . 21Annex E (normative) Flammability test 23E.1 Test pieces 23E.2 Apparatus 23E.3 Test method . 23Anne
15、x F (informative) Resistance to chemicals conveyed 25BS EN 12115:2011EN 12115:2011 (E) 3 F.1 General . 25F.2 Suitability of hose 25F.3 Resistance of end fitting materials 25F.4 Conveyance of chemicals other than those listed in Table F.2 26Bibliography 50BS EN 12115:2011EN 12115:2011 (E) 4 Foreword
16、This document (EN 12115:2011) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endors
17、ement, at the latest by July 2011, and conflicting national standards shall be withdrawn at the latest by July 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying
18、any or all such patent rights. This document supersedes EN 12115:1999. In comparison with EN 12115:1999 the following changes have been made: a) the test procedure to determine the electrical resistance through the hose wall is given in Annex A (normative); b) a list of hose lining material resistan
19、t to specific chemical substances, identified by CAS number, has been added as Annex F (informative); c) the normative references have been updated. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European
20、 Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kin
21、gdom. BS EN 12115:2011EN 12115:2011 (E) 5 Introduction This European Standard has been prepared to provide minimum acceptable requirements for the satisfactory performance of flexible rubber and thermoplastics hoses and hose assemblies with unspecified reinforcement and linings of different types of
22、 synthetic rubbers and thermoplastics, for each chemical substance conveyed. A list of hose lining material resistant to specific chemical substances, identified by CAS number, has been added as Annex F (informative). This list is for information only. BS EN 12115:2011EN 12115:2011 (E) 6 1 Scope Thi
23、s European Standard specifies requirements for two types of hose assemblies (Types D and SD) and four grades based on electrical properties with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous chemical substances, hereinafter termed the “ch
24、emicals conveyed“. The hose assemblies are intended for use with chemicals conveyed in the temperature range of -20 C to +65 C at a working pressure 10 bar1). NOTE 1 This European Standard sets out requirements for these hose assemblies to ensure that users are not exposed to danger from fire or exp
25、losion and that the environment is protected against contamination or damage. NOTE 2 Other temperatures and working pressures than those given above can be agreed with the manufacturer, provided that the marking on the hose (see 14.1) states this and the requirements of Table 5 and all the other req
26、uirements are met. NOTE 3 Other diameters than those given in this European Standard can be agreed with the manufacturer. NOTE 4 This European Standard also provides guidance on the storage of hose assemblies (Clause 15). NOTE 5 The attention of users is drawn to Annex F concerning the selection of
27、lining material related to the chemical(s) to be conveyed by the hoses and/or hose assemblies. This standard does not apply to hose assemblies for: aircraft refuelling (EN 1361); fuel dispensing (EN 1360); oil burners (EN ISO 6806); refrigerant circuits; fuel truck delivery (EN 1761); liquid petrole
28、um gases (LPG) (EN 1762); fire fighting (EN ISO 14557); oil suction and discharge (EN 1765); rotary drilling (EN ISO 6807); fuel dispensing with vapour recovery system (EN 13483). This European Standard does not apply to multilayer hose assemblies (EN 13765 and EN 13766). 1) 1 bar = 0,1 MPa. BS EN 1
29、2115:2011EN 12115:2011 (E) 7 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applie
30、s. EN 10244-2, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN 10270-1, Steel wire for mechanical springs Part 1: Patented cold drawn unalloyed spring steel wire EN 10270-2, Steel wire for mechanical springs Part 2: Oil hardened and tem
31、pered spring steel wire EN ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing (ISO 1402:2009) EN ISO 1746, Rubber or plastics hoses and tubing Bending tests (ISO 1746:1998, including technical corrigendum 1:1999) EN ISO 4671, Rubber and plastics hoses and hose assemblies Met
32、hods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007) EN ISO 4672:1999, Rubber and plastics hoses Sub-ambient temperature flexibility tests (ISO 4672:1997) EN ISO 7233, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuum (IS
33、O 7233:2006) EN ISO 7326, Rubber and plastics hoses Assessment of ozone resistance under static conditions (ISO 7326:2006) EN ISO 8031:2009, Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity (ISO 8031:2009) EN ISO 8033, Rubber and plastics hoses De
34、termination of adhesion between components (ISO 8033:2006) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies Vocabulary (ISO 8330:2007) ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties ISO 188, Rubber, vulcanized or thermoplastic Accelerated
35、 ageing and heat resistance tests ISO 1629, Rubber and latices Nomenclature ISO 1817, Rubber, vulcanized Determination of the effect of liquids ISO 4649:2002, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device ISO 8331, Rubber and plasti
36、cs hoses and hose assemblies Guidelines for selection, storage, use and maintenance BS 3592-1:1986, Steel wire for hose reinforcement Specification for coated round and flat steel wire for rubber hose reinforcement 3 Terms and definitions For the purposes of this document, the terms and definitions
37、given in EN ISO 8330:2008 apply. BS EN 12115:2011EN 12115:2011 (E) 8 NOTE In this European Standard the word “fitting“ has been used; this is, in some cases, interchangeable with the word “coupling“. 4 Classification Hoses and hose assemblies for this application shall be divided into two types, acc
38、ording to their duty requirements: Type D: hoses and hose assemblies for delivery duty only; Type SD: hoses and hose assemblies for suction and delivery duty. Hoses and hose assemblies for this application shall be divided into four grades: Grade M: electrically bonded; Grade : electrically conducti
39、ve; see EN ISO 8031:2009, Annex A for new recommended marking to indicate conductive lining, conductive cover or conductive lining and cover; Grade M/T: electrically bonded and with an electrical resistance through the hose wall not exceeding 109; Grade /T: electrically conductive and with an electr
40、ical resistance through the hose wall not exceeding 109. 5 Couplings and end fittings Hoses shall be fitted with end fittings and couplings to form hose assemblies. Examples are given in Annex C. 6 Materials and construction 6.1 General Hoses Type D shall consist of a lining, reinforcement and a cov
41、er. Hoses Type SD shall consist of a lining, reinforcement and a cover, and in addition incorporate one or more helixes. 6.2 Lining The lining shall be resistant to the chemical substances conveyed. The lining shall be uniform in quality and thickness and shall be free from porosity, air holes, fore
42、ign inclusions and other defects which could impair the expected use. 6.3 Cover The cover shall be resistant to mechanical damage, wear and environmental effects due to weather and short-term chemical exposure. 6.4 Reinforcement The reinforcement shall consist of a textile material which is resistan
43、t to the medium conveyed. BS EN 12115:2011EN 12115:2011 (E) 9 6.5 Helical wires The helix or helixes shall be fully embedded into the hose wall so that contact with the medium conveyed is avoided. 7 Dimensions and tolerances, typical masses 7.1 Diameters, thickness, vacuum stability, bend radii and
44、resistance to vacuum The inside and outside diameters of the hoses, the minimum thickness of lining and cover and the minimum bend radius shall conform to the values given in Table 1 or Table 2 (depending on the type). The Type D hoses shall be able to withstand an internal vacuum as specified in Ta
45、ble 1 (vacuum stability) without collapse or changes in diameter and length in excess of the values specified in Table 5. Table 1 Dimension requirements, Type D hoses Nominal bore Inside diameter mm Tolerance mm Outside diameter mm Tolerancemm Minimum thickness mm Bend radius mm min bVacuumstability
46、 bar lining acover 13 13,0 0,5 23,0 1,0 2,0 1,6 90 -0,5 19 19,0 31,0 125 25 25,0 37,0 150 -0,4 32 32,0 44,0 175 38 38,0 51,0 225 50 50,0 0,7 66,0 1,2 2,0 2,0 275 -0,3 51 51,0 67,0 275 63 63,0 0,8 79,0 300 75 75,0 91,0 350c76 76,0 92,0 350c100 100,0 116,0 1,6 450c101,5 101,5 118,0 450caThe dimensions
47、 for the minimum lining thickness do not apply to hoses made from materials PE-X/UPE and fluoro-plastics. The thickness for these materials shall be 0,4 mm. bThe bend radii specified do not apply to hoses made from PE-X/UPE and fluoro-plastics where the value shall be 1,5 x the values shown above. c
48、Only applies to operation at not less than 1 bar, otherwise the hose will kink. The Type SD hoses shall be able to withstand an internal vacuum as specified in Table 2 (resistance to vacuum) and shall conform to the requirements specified in Table 5. BS EN 12115:2011EN 12115:2011 (E) 10 Table 2 Dime
49、nsion requirements, Type SD hoses Nominal bore Inside diameter mm Tolerance mm Outside diameter mm Tolerancemm Minimum thicknessmm Bend radius mm min bResistance to vacuumbar lining acover 19 19,0 0,5 31,0 1,0 1,6 1,6 125 -0,8 25 25,0 37,0 150 32 32,0 44,0 175 38 38,0 51,0 225 50 50,0 0,7 66,0 1,2 1,7 1,7 275 51 51,0
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1