ImageVerifierCode 换一换
格式:PDF , 页数:20 ,大小:1.82MB ,
资源ID:570153      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-570153.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS EN 12211-2016 Windows and doors Resistance to wind load Test method《窗和门 抗风性 试验方法》.pdf)为本站会员(brainfellow396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

BS EN 12211-2016 Windows and doors Resistance to wind load Test method《窗和门 抗风性 试验方法》.pdf

1、BS EN 12211:2016Windows and doors Resistance to wind load TestmethodBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12211:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12211:2016. It supersedes BS EN 12211:2000 which

2、 is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/538/1, Windows and doors.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contr

3、act. Users are responsible for its correct application. The British Standards Institution 2016 .Published by BSI Standards Limited 2016ISBN 978 0 580 84016 6 ICS 91.060.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the a

4、uthority of the Standards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 12211:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12211 March 2016 ICS 91.060.50 Supersedes EN 12211:2000English Version Windows and do

5、ors - Resistance to wind load - Test method Fentres et portes - Rsistance au vent - Mthode dessai Fenster und Tren - Widerstandsfhigkeit bei Windlast - Prfverfahren This European Standard was approved by CEN on 9 January 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations

6、 which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. Thi

7、s European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN memb

8、ers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug

9、al, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form

10、 and by any means reserved worldwide for CEN national Members. Ref. No. EN 12211:2016 EBS EN 12211:2016EN 12211:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principles of test 5 5 Apparatus . 5 6 Preparation of test specimen 6 6.1 Se

11、t-up of the test specimen 6 6.2 Set-up of measuring devices for frontal deflection . 6 7 Test procedure . 6 7.1 Preliminaries 6 7.2 Deflection test. 7 7.2.1 General 7 7.2.2 Positive pressure . 7 7.2.3 Negative pressure . 7 7.3 Repeated pressure test . 7 7.4 Safety test . 7 8 Deflection . 8 9 Repeate

12、d pressure 8 10 Safety test . 8 11 Test report . 8 Annex A (informative) Deflection measurements . 10 Annex B (informative) Resistance to wind load test sequence . 14 Bibliography . 15 BS EN 12211:2016EN 12211:2016 (E) 3 European foreword This document (EN 12211:2016) has been prepared by Technical

13、Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, an

14、d conflicting national standards shall be withdrawn at the latest by September 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. T

15、his document supersedes EN 12211:2000. The revision of this European Standard clarifies only the test method and does not affect existing test evidence of EN 12211:2000. This European Standard is one of a series of standards for windows and doors. In comparison with EN 12211:2000, the following sign

16、ificant changes were made: a) Clause 3: Supplement of definition “closing condition”; b) Sub-clause 3.2: Simplification of definition “test pressure”; c) Sub-clause 5.4: Revision of definition accuracy“; d) Sub-clause 7.1: Addition of closing condition“; e) Clause 11: Supplement of necessary descrip

17、tion of test specimen; f) Annex A: Renumeration of figures; g) Annex A: Revision of A.1 and A.2; h) Annex A: Supplement of Figure A.4 (new) Measuring points on single and double leaf doors (example); i) Annex B: Revision of Figure B.1. According to the CEN/CENELEC Internal Regulations, the national

18、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

19、a, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12211:2016EN 12211:2016 (E) 4 1 Scope This European Standard defines the test method to determine the resistance to wind load for completely asse

20、mbled windows and pedestrian doorsets of any materials when submitted to positive or negative test pressures. This test method is designed to take account of conditions in use, when the window or door is installed in accordance with the manufactures specification and the requirements of relevant Eur

21、opean Standards and codes of practice. This European Standard does not apply to joints between the window or door frame and the building construction. This European Standard is not intended to evaluate strength of the glass. 2 Normative references The following documents, in whole or in part, are no

22、rmatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1026, Windows and doors Air permeability Test method EN

23、12519, Windows and pedestrian doors Terminology 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12519 and the following apply. 3.1 closing condition 3.1.1 closed movable parts rest in or at the fixed parts in a way in which they may be fastened (latch

24、ed and/or locked) 3.1.2 fastened where the movable part is restrained at one or more points and shall be described by at least one of the two as listed below 3.1.2.1 latched movable part is returned to its closed position and restrained by either a) a self - engaging fastener or b) a roller catch or

25、 c) a latch 3.1.2.2 locked movable part is further restrained in the closed position by additional operations (of e.g. handle, key, automatic devices or electronic devices) to engage integrated locking devices (e.g. nutbolts or deadbolts) which will affect the products characteristics BS EN 12211:20

26、16EN 12211:2016 (E) 5 3.1.3 secured any action(s) which prevent unauthorised release of the fastening device(s) to allow exit or entry (e.g. child safety, burglary) 3.2 frontal displacement movement of a point on a frame member measured normal to the member 3.3 frontal deflection maximum frontal dis

27、placement of a frame member minus half the sum of the frontal displacements at each end of the member 3.4 relative frontal deflection frontal deflection of a frame member divided by the length of the member over which the frontal deflection was measured, e.g. distance between the ends of the member

28、3.5 test pressure difference between the static air pressures inside and outside of the test chamber Note 1 to entry: The test pressure is positive if the static air pressure inside the chamber of the test apparatus is higher than that outside the test chamber. Note 2 to entry: The test pressure is

29、negative if the static air pressure inside the chamber of the test apparatus is lower than that outside the test chamber. For the purpose of these tests, three sets of test pressure are defined: P1 applied to measure deflections of parts of the test specimen; P2 pulsating pressure applied for 50 cyc

30、les to assess performance under repeated windloads; P3 applied to assess the safety of the test specimen under extreme conditions. The values of P1, P2, P3 are related as follows: P2 = 0,5 P1 and P3 = 1,5 P1. 4 Principles of test Application of a defined series of pressures (positive and negative) a

31、t which measurements and inspections are made to assess relative frontal deflection and resistance to damage from wind loads. 5 Apparatus 5.1 A chamber with an open side to which the test specimen can be fitted. It shall be constructed so as to be able to withstand the test pressures without deflect

32、ing to an extent likely to influence the test results. 5.2 Means for applying controlled test pressure to the test specimen. 5.3 Means of producing rapid changes in test pressure, controlled within defined limits. BS EN 12211:2016EN 12211:2016 (E) 6 5.4 Instrument suitable for measuring the quantity

33、 of air flow into or out of the chamber with an accuracy of 5 % of the measured value for air flows greater than 1 m/h and an accuracy of 0,05 m/h for air flows equal to or smaller than 1 m/h. NOTE 1 Accuracy = (the sum of the amount of the error plus the amount of the expanded measurement uncertain

34、ty). For values of both error and expanded measurement uncertainty see last calibration certificate of the instrument. NOTE 2 For vocabulary of metrology see ISO/IEC Guide 99:2007 5.5 Means of measuring the test pressure applied across the test specimen, within an accuracy of 5 %. 5.6 Devices, such

35、as dial gauges or displacement transducers, for measuring displacements of measured points with a resolution of 0,1 mm and an accuracy of 5 %. 5.7 Means for fitting the measuring devices properly to ensure their stability during the test. 5.8 A measuring tape accurate to 1 mm to measure the necessar

36、y dimensions (e.g. frame members) of the test specimen. 6 Preparation of test specimen 6.1 Set-up of the test specimen The test specimen shall be fixed as intended for use without any twists or bends which may influence the test results. The test specimen shall be fully operable. The stiffness of th

37、e test rig and the fixing of the test specimen to it shall be sufficient to avoid adverse effects on the performance of the test specimen during testing. The test specimen shall be cleaned and surfaces dry. 6.2 Set-up of measuring devices for frontal deflection Measuring devices (see 5.6) shall be f

38、ixed in position at each end and at the centre of the frame member to be measured. Alternatively, a single measuring device shall be fixed at the centre of a rigid beam that is fixed to and supported as close as possible to the ends of the frame member to be measured. NOTE A frame member could be pa

39、rt of the opening element or the fixed frame. For positioning of measuring devices see Figure A.1 to A.4. 7 Test procedure 7.1 Preliminaries The ambient temperature and humidity close to the test specimen shall be within the range of 10 C to 30 C and 25 % to 75 % RH and the test specimen shall be co

40、nditioned thus for at least 4 h immediately before test. The test specimen shall be brought into the defined closing condition in accordance with the manufacturers instructions. Figure B.1 shows the test sequence of the test to be carried out and the set of test pressures and their features to be ap

41、plied. BS EN 12211:2016EN 12211:2016 (E) 7 The test for air permeability in accordance with EN 1026 shall be completed before testing the resistance to wind load to test pressures P1 and P2. 7.2 Deflection test 7.2.1 General Record the length of the members whose frontal deflection is to be measured

42、. NOTE If several displacements or deflections are to be measured, they can be recorded either during one sequence of test pressure steps to P1 or during as many sequences to P1 as there are measurements to be made. 7.2.2 Positive pressure Apply three pressure pulses, each 10 % greater than the test

43、 pressure P1. The time to reach the maximum pressure shall not be less than 1 s and it shall be sustained for at least 3 s. All the gauges shall be set to zero or have their initial reading recorded. Apply test pressure equal P1 according to the classification required for the test specimen, at a ra

44、te not exceeding 100 Pa/s, either incrementally or continuously. When the pressure P1 has been applied for 30 s, record the required frontal deflection(s) or frontal displacement(s). Reduce the test pressure to 0 Pa, at a rate not greater than 100 Pa/s and after (60 5) s record the residual frontal

45、deflection(s) or frontal displacement. 7.2.3 Negative pressure Apply procedure specified in 7.2.2 using negative test pressures. 7.3 Repeated pressure test The test specimen shall be subjected to 50 cycles including negative and positive pressures, with the following features: test pressure equal P2

46、; first step is negative, next is positive as is the last of the sequence of 50 impulses; variation from P2 to +P2 and the reverse shall take (7 3) s; value P2 is maintained at least for (7 3) s. After completion of the 50 cycles, open and close the moving parts of test specimen and note damage or f

47、unctioning defects if any. Repeat the test for air permeability in accordance with EN 1026. 7.4 Safety test The test specimen shall be subjected to one cycle including negative and positive test pressure with the following features: test pressure equal P3; negative test pressure is applied first; va

48、riation from 0 Pa to P3 and back from P3 to 0 Pa shall take (7 3) s, the maximum test pressure P3 shall be maintained for (7 3) s; BS EN 12211:2016EN 12211:2016 (E) 8 positive test pressure is applied after a (7 3) s rest at 0 Pa; variation from 0 Pa to +P3 and back to 0 Pa shall be the same duratio

49、n as for the negative test pressure -P3. After the safety test record whether the test specimen remains closed and describe any parts of the test specimen which have become detached. 8 Deflection Deflection(s) and displacement, under pressure steps +P1 and P1 shall be recorded. Relative frontal deflections shall be calculated in the form of fractions with the numerator equal to 1 and the denominator expressed to 3 significant figures. 9 Repeated pressure Record any damage and operating defects. 10 Safet

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1