BS EN 122150-1996 Harmonized system of quality assessment for electronic components - Sectional specification radio frequency coaxial connectors - Series EIA Flange《电子元器件质量评定体系 EIA.pdf

1、BRITISH STANDARD BS EN 122150:1996 Harmonized system of quality assessment for electronic components Sectional specification: Radio frequency coaxial connectors Series EIA Flange The European Standard EN 122150:1993 has the status of a British Standard ICS 33.120.30BSEN122150:1996 This British Stand

2、ard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15August1996 BSI 04-2000 The following BSI references relate to the work on this standard: Committee reference EPL/46/4 Draft announced i

3、n BSI News April 1996 ISBN 0 580 26233 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, RF connectors and accessories for communication and signalling, to Subcommittee EPL/46/4, RF c

4、onnectors, upon which the following bodies were represented: AEA Technology BEAMA Electrical Cable together with the voting report, circulated as document CECC (Secretariat) 3341 it was approved by CECC as EN122150 on7May1993. The following dates were fixed: Contents Page Foreword 2 Introduction 5 S

5、ection 1. Scope 7 Section 2. Mating face and gauge information 2.1 Dimensions 8 2.2 Drawings 8 2.3 Gauges for male centre contacts 21 Section 3. Properties 3.1 Ratings and characteristics 24 Section 4. Test conditions and severities 4.1 Measurement and recovery conditions 27 4.2 Visual examination 2

6、7 4.3 Dimensions 27 4.4 Electrical tests and measurements 27 4.5 Mechanical tests and measurements 28 4.6 Environmental tests and measurements 30 4.7 Endurance tests 33 Section 5. Quality assessment procedures 5.1 Test schedules and inspection requirements 34 Figure 1 9 Figure 2 11 Figure 3 13 Figur

7、e 4 15 Figure 5 17 Figure 6 19 Figure 7 Sizing and retention force gauges for male centre contacts 21 Table 1 10 Table 2 12 Table 3 14 Table 4 16 Table 5 18 Table 6 20 Table 7 21 Table 8 Dimensions of sizing and retention force gauges, seeFigure 7 22 latest date of announcement of the EN at national

8、 level (doa) 1993-09-03 latest date of publication of an identical national standard a (dop) 1994-03-03 latest date of withdrawal of conflicting national standards a (dow) 1995-03-03 a National Standard (excluding National implementation of IECQ Specifications)EN122150:1993 BSI 04-2000 3 Preface Thi

9、s sectional specification (SS) was prepared by CECC Working Group22: R.F. Connectors. It is based, wherever possible, on the Publications of the International Electrotechnical Commission and in particular on IEC339-2:1972: General purpose rigid coaxial lines and their associated flange connectors. T

10、his SS and its associated blank detail specifications(s) BDS are specific to the six sizes of EIA FLANGE connectors and their related accessories. The text of this specification was circulated to the CECC for voting in the documents listed below and was ratified by the President of the CECC for prin

11、ting as a CECC specification: Series EIA FLANGE connectors of the types covered by this SS are available in six sizes, each size having a different mating face but employing structurally similar principles of mechanical construction. The connections described are derived from EIA and IEC standards,

12、and include versions for both507 and757 systems. Document Voting Date Report on the Voting CECC(Secretariat)1710 July 1985 CECC(Secretariat)1852EN122150:1993 4 BSI 04-2000 Document numbering for r.f. connector specifications follows2.2 1) of CECC00400-III, in order to permit the issue of more than n

13、ine sectional specifications. The approved numbering system applicable to r.f. connector specifications is illustrated in the diagram below. NOTEA detail specification is a “completed” blank detail specification.EN122150:1993 BSI 04-2000 5 Introduction Although EIA FLANGE connectors were originally

14、intended for use with rigid coaxial air lines only, they are currently available in a number of additional styles and variants, suitable for use with semi-flexible cables having convoluted outer conductors. The outer conductor mating interface is sexless, each half of a mated pair having an identica

15、l coupling flange. Two intermateable versions of the coupling flange are available, fixed and rotatable (swivel type). Connectors with fixed flanges have IEC type designations ending2. Swivel type flange connectors have IEC designations ending in3. With both fixed and swivel type flange connectors,

16、the inner conductor connection is by means of a separate coupling element comprising a double-ended male contact and insulator assembly (Bullet). When the connector is used in conjunction with rigid lines, the Bullet may form the only mechanical support for the centre conductor. The connector sizes

17、relate to the nominal outside diameter of the rigid coaxial transmission line with which they were intended to be used. The size was originally expressed in fractional inches, but the IEC type designation for rigid coaxial lines includes both the nominal characteristic impedance, and the outside dia

18、meter in millimetres rounded to a convenient whole number. SUMMARY OF DIMENSIONS 50 7 Line Size 75 7 Line Size UPPER FREQUENCY LIMITS The upper frequency limit of operation is determined by the cut-off frequency of higher order “waveguide” modes of propagation, and the effect which they have on the

19、impedance and transmission characteristics of the normal TEM coaxial transmission line mode. The lowest cut-off frequency occurs with the TE 11waveguide mode, and this cut-off frequency in an air dielectric line is the upper frequency limit of a practical coaxial transmission line. In general it is

20、not advisable to operate coaxial systems at frequencies greater than95% of the TE 11mode cut-off frequency; this particularly applies in the vicinity of discontinuities such as undercuts and support insulators. The table below lists the recommended upper frequency limits for both straight and right-

21、angle EIA FLANGE connectors of both507 and757 impedance. Rigid Line 339 IEC 50- Outer Conductor Inner Conductor Original Inch O/D Nominal O/D mm Nominal I/D mm Nominal O/D mm Nominal I/D mm 22-1 40-1 80-1 105-1 125-1 155-1 7/8 1.5/8 3.1/8 4.1/2 6.1/8 (0,875) (1,625) (3,125) (4,173) (4,850) (6,125) 2

22、2,23 41,30 79,40 106,00 123,20 155,60 20,00 38,80 76,80 103,00 120,00 151,92 8,70 16,90 33,40 44,80 52,10 66,00 7,40 15,00 31,30 42,80 50,10 64,00 Rigid Line 339 IEC 75- Outer Conductor Inner Conductor Original Inch O/D Nominal O/D mm Nominal I/D mm Nominal O/D mm Nominal I/D mm 22-1 40-1 80-1 7/8 1

23、.5/8 3.1/8 (0,875) (1,625) (3,125) 22,23 41,30 79,40 20,00 38,80 76,80 5,80 11,10 22,10 4,50 9,60 20,30EN122150:1993 6 BSI 04-2000 50 7 Line Size 75 7 Line Size Rigid Line 339 IEC 50- Theoretical TE 11mode f c(GHz) Straight Connector f c 0,95 Right Angle Connector f c 0,665 22-1 40-1 80-1 105-1 125-

24、1 155-1 6,65 3,43 1,73 1,29 1,11 0,88 6,32 3,26 1,64 1,23 1,05 0,83 4,42 2,28 1,15 0,86 0,74 0,58 Rigid Line 339 IEC 75- Theoretical TE 11mode f c(GHz) Straight Connector f c 0,95 Right Angle Connector f c 0,665 22-1 40-1 80-1 7,40 3,83 1,93 7,03 3,64 1,83 4,92 2,54 1,28EN122150:1993 BSI 04-2000 7 S

25、ection 1. Scope This sectional specification (SS) provides information and rules for the preparation of detail specifications (DS) for general purpose connectors Series EIA Flange. It prescribes mating-face dimensions for general purpose connectors, together with gauging information and mandatory te

26、sts, selected from CECC22000, applicable to all DS relating to Series EIA FLANGE connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS, and covers test schedules and inspection requirements for Assessment Levels H, M and U.EN122150:19

27、93 8 BSI 04-2000 Section 2. Mating interface and gauge information 2.1 Dimensions Inch dimensions are original dimensions. All undimensioned pictorial configurations are for reference purposes only. 2.2 Drawings Drawings, Figure1 to Figure6 inclusive, provide mating interface details for the six siz

28、es of EIA FLANGE connector, the relevant dimensions being shown inTable 1 toTable 6. The following NOTES apply to all six drawings: NOTE 1Swivel type flanges shall be free to rotate. NOTE 2Diameters D, g, s and t shall be on, or capable of taking up, a common axis relative to datum diameter AO. NOTE

29、 3Contact diameter C and chamfer shall meet mechanical and electrical performance requirements after slotting and forming. The number, width and depth of slots is optional. NOTE 4The fitting of locating pins is optional and to be regarded as inactive for new designs.EN122150:1993 BSI 04-2000 9EN 122

30、150:1993 10 BSI 04-2000 Table 1 Dimensions: 339 IEC 50-22-2 339 IEC 75-22-2 (7/8 in Line Size) 339 IEC 50-22-3 339 IEC 75-22-3 Dim. Inch mm Remarks min. max. min. max. a 1,344 34,15 Previously overall length in IEC 339-2 b 0,469 0,500 11,90 12,70 Centre conductor to reference plane c a 0,953 0,984 2

31、4,20 25,00 Groove for contact latch (optional) d a 1,047 1,077 26,60 27,35 Groove for contact latch (optional) e a 0,039 0,051 1,00 1,30 Groove depth (optional) f 0,121 0,122 3,08 3,10 Guide pin diameter (optional) g 1,346 1,354 34,20 34,40 OD of “O”-ring groove h 1,024 1,031 26,00 26,20 ID of “O”-r

32、ing groove l Applicable to 1.5/8 in connector with square flange only m 0,093 0,098 2,35 2,50 Depth of recess for dielectric n 0,177 4,50 Guide pin length (optional) p 0,047 0,053 1,20 1,35 Depth of “O”-ring groove r 0,008 0,024 0,20 0,60 Flange to reference plane s 1,750 (true position) 44,45 (true

33、 position) See drawing for positional tolerance t 1,812 (true position) 46,02 (true position) See drawing for positional tolerance u 0,130 0,134 3,30 3,40 Diameter of locating holes v 0,274 0,285 6,95 7,25 Diameter of fixing bolt holes A 0,815 0,821 20,70 20,85 Diameter of recess for dielectric B 0,

34、782 0,788 19,86 20,02 ID of outer conductor of 7/8 in rigid line C See Note 3 See Note 3 Male contact diameter D 50 7 0,289 0,293 7,34 7,44 ID of 50 7 female contact D 75 7 0,174 0,178 4,42 4,52 ID of 75 7 female contact E a 0,882 0,894 22,40 22,70 To accept OD of rigid air line F 1,346 34,20 Min. depth of female contact bore G 0,469 11,90 Max. centre conductor length H 0,181 0,185 4,60 4,70 Thickness of dielectric support J 0,808 0,812 20,50 20,60 OD of dielectric support a These features apply only to connectors intended for permanent attachment to rigid coaxial air lines.