BS EN 12317-2-2010 Flexible sheets for waterproofing - Determination of shear resistance of joints - Plastic and rubber sheets for roof waterproofing《防水柔性板 连接点耐剪切强度的测定 屋顶防水用塑料和橡胶薄板.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12317-2:2010Flexible sheets forwaterproofing Determination of shearresistance of jointsPart 2: Plastic and rubber sheets for roofwaterproofingBS EN 12317-2:2010 BRITISH STA

2、NDARDNational forewordThis British Standard is the UK implementation of EN 12317-2:2010.It supersedes BS EN 12317-2:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/546/2, Plastics and rubber sheets for Waterproofing.A list of organizations repres

3、ented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 59217 1ICS 91.100.50Compliance with a British Standard cannot confer imm

4、unity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2010Amendments issued since publicationDate Text affectedBS EN 12317-2:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12317-2 July 2010 ICS 91.100.50

5、 English Version Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing Feuilles souples dtanchit - Dtermination de la rsistance au cisaillement des joints - Partie 2: Feuilles dtanchit de toiture plastiques et lasto

6、mres Abdichtungsbahnen - Bestimmung des Scherwiderstandes der Fgenhte - Teil 2: Kunststoff- und Elastomerbahnen fr Dachabdichtungen This European Standard was approved by CEN on 29 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

7、giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official

8、 versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Be

9、lgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN CO

10、MMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12317-2:2010: EBS EN 12317-2:2010EN

11、 12317-2:2010 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Principle 55 Apparatus .56 Sampling .67 Preparation of test pieces and test specimens 68 Procedure .79 Expression of results 79.1 Jointing information 79.2 Evaluation .79.3 Precisi

12、on of the test method 710 Test report 7Annex A (informative) Failure modes 9BS EN 12317-2:2010EN 12317-2:2010 (E) 3 Foreword This document (EN 12317-2:2010) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This European

13、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at the latest by January 2011. Attention is drawn to the possibility that some of the element

14、s of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12317-2:2000. This European Standard “Flexible sheets for waterproofing - Determination of shear resistance of joints” c

15、onsists of two parts: - Part 1: Bitumen sheets for roof waterproofing; - Part 2: Plastic and rubber sheets for waterproofing. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

16、gium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 12317-

17、2:2010EN 12317-2:2010 (E) 4 Introduction This European Standard is intended for characterisation of plastic and rubber sheets as manufactured or supplied before use. This test method relates to products or to their components where appropriate, and not to waterproofing membrane systems composed of s

18、uch products and installed in the works. This test is intended to be used in conjunction with EN 13956, Flexible sheet for waterproofing Plastic and rubber sheets for roof waterproofing Definitions and characteristics. BS EN 12317-2:2010EN 12317-2:2010 (E) 5 1 Scope This European Standard specifies

19、a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing. NOTE The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jo

20、inting, the size of the overlap and the workmanship. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

21、g any amendments) applies. EN 13416, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/ compression testing machines Verification and calibr

22、ation of the force-measuring system (ISO 7500-1:2004) 3 Terms and definitions For the purposes of this document, the following term and definition apply. 3.1 shear resistance maximum tensile force required to extend a prepared joint test specimen, in shear, until it breaks or separates 4 Principle T

23、he principle of the test is to pull a specimen of a joint in shear at a constant speed until it breaks or separates. The tensile force is continuously recorded throughout the test. 5 Apparatus Tensile testing machine equipped with a continuous recording of force and corresponding extension and capab

24、le of maintaining a uniform speed of grip separation as specified below. The tensile testing machine shall have a sufficient loading capacity in excess of 2000 N and a grip separation speed of (100 10) mm/min. The width of grips shall not be less than 50 mm. The tensile testing machine shall be equi

25、pped with grips of a type, which maintain or increase the clamping pressure as a function of the increase of the force applied to the test specimen. The test specimen shall be held so that it does not slip in the grips more than 2 mm. The method of gripping shall not induce premature rupture close t

26、o the grips. The force measuring system shall meet at least Class 2 of EN ISO 7500-1 (i.e. 2 %). BS EN 12317-2:2010EN 12317-2:2010 (E) 6 6 Sampling Samples shall be taken in accordance with EN 13416. 7 Preparation of test pieces and test specimens Test pieces to be used for jointing should be previo

27、usly conditioned for at least 20 h at (23 2) C and at a relative humidity between 30 % and 70 %. Test pieces of the sheet are joined by the method(s) to be used for installation, both for side lap and end lap jointing, with an overlap that is specified for the product. After jointing, the test piece

28、 shall be conditioned for a minimum of 2 h at (23 2) C and at (50 5) % RH before testing unless the manufacturer recommends differently. From each of these joint test pieces five rectangular test specimens (50 1) mm wide shall be taken perpendicular to the joint. They shall have such a length, so th

29、at the ends of the initial distance between the two grips is (200 5) mm with the joint in the middle (see Figure 1). Dimensions in millimetres 1w200 5Key 1 grip w width of joint Figure 1 Shear strength testing of joint BS EN 12317-2:2010EN 12317-2:2010 (E) 7 8 Procedure The test specimen shall be fi

30、rmly held in the grips of the tensile testing machine, taking care that the longitudinal axis of the test specimen, the axis of the tensile testing machine and the grips are correctly aligned. Each test specimen shall be marked at the grips in order to identify any slippage out of the grips. The cle

31、ar distance between the grips shall be between 3 and 4 times the width of the joint with a minimum of 120 mm and a maximum of 200 mm. No preload shall be applied. The test is carried out on a test specimen at a temperature of (23 2) C and at a constant separating speed for the grips of (100 10) mm/m

32、in. The applied tensile force shall be recorded continuously until the test specimen ruptures or shears. The mode of failure shall be recorded. 9 Expression of results 9.1 Jointing information State all relevant information on the formation and the conditioning of the joint. 9.2 Evaluation The mode

33、of failure of each of the specimens shall be reported (see Annex A). The shear resistance of the specimen is the maximum force recorded during the test. List the individual values for each set of five specimens in Newton. Calculate and state the shear resistance of the joint as the mean value to the

34、 nearest Newton. Calculate and state the standard deviation. Disregard any test result where the test specimen breaks less than 10 mm from the grips or slips by more than the permitted limit within the grips of the tensile testing machine, and retest with a replacement specimen. 9.3 Precision of the

35、 test method No information is available at this time. 10 Test report The test report shall include at least the following information: a) reference to this document (EN 12317-2) and any deviation from it; b) all details necessary to identify the product tested; c) all details of how the weld was ca

36、rried out; d) information on sampling in accordance with Clause 6; e) details of preparation of the test specimen in accordance with Clause 7; BS EN 12317-2:2010EN 12317-2:2010 (E) 8 f) test results in accordance with Clause 9; g) the shear resistance and the failure mode; h) any peculiarities in th

37、e method employed or encountered during the test; i) date of the test(s). BS EN 12317-2:2010EN 12317-2:2010 (E) 9 Annex A (informative) Failure modes Figure A.1 Failure modes This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for prepar

38、ing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick

39、 High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. W

40、e would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an ind

41、ividual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the w

42、ebsite addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that hav

43、e been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information s

44、ervices are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and

45、other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI pub

46、lications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic,

47、 photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: