BS EN 12467-2012 Fibre-cement flat sheets Product specification and test methods《纤维水泥平板材 产品规范和试验方法》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12467:2012Fibre-cement flat sheets Product specification and testmethodsCopyright European Committee for Standardization Provided by IHS under license with CENNot for Resal

2、eNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12467:2012. Itsupersedes BS EN 12467:2004 which is withdrawn.The UK participation in its preparation was entrusted to Technical

3、Committee B/542/4, Fibre reinforced cement sheeting for roofing.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. T

4、he British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 72597 5ICS 91.100.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30

5、September 2012.Amendments issued since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE N

6、ORM EN 12467 September 2012 ICS 91.100.40 Supersedes EN 12467:2004English Version Fibre-cement flat sheets - Product specification and test methods Plaques planes en fibres-ciment - Spcifications du produit et mthodes dessai Faserzement-Tafeln - Produktspezifikation und Prfverfahren This European St

7、andard was approved by CEN on 4 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning

8、 such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its

9、 own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, German

10、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR N

11、ORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12467:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo r

12、eproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EN 12467:2012 (E) 2 Contents Page Foreword 41 Scope 52 Normative references 53 Terms and definitions .54 Symbols and abbreviations 75 Requirements .85.1 General 85.1.1 Composition .85.1.2 Appearance and finish 85.2 Clas

13、sification 85.2.1 General 85.2.2 Category A 95.2.3 Category B 95.2.4 Category C 95.2.5 Category D 95.2.6 Groups of sizes 95.3 Dimensions and tolerances 95.3.1 General 95.3.2 Nominal length and width .95.3.3 Thickness .95.3.4 Tolerances on nominal dimensions 105.3.5 Tolerances on shape 115.4 Physical

14、 requirements and characteristics . 115.4.1 General . 115.4.2 Apparent density. 115.4.4 Mechanical characteristics Bending strength (MOR) Modulus of elasticity (MOE) . 125.4.5 Water impermeability for Categories A, B and D . 125.4.6 Water vapour permeability for Category D 125.5 Durability requireme

15、nts . 135.5.1 General . 135.5.2 Freeze-thaw for Categories A, B and D 135.5.3 Heat-rain for Categories A and B 135.5.4 Warm water for Categories A, B, C and D 135.5.5 Soak-dry for Categories A, B , C and D 135.6 Fire and safety . 135.6.1 Reaction to fire 135.6.2 Release of dangerous substances 135.7

16、 Product information 136 Evaluation of conformity 146.1 General . 146.2 Initial type testing . 146.3 Factory production control (FPC) . 166.3.1 General . 166.3.2 Acceptance tests 166.3.3 Equipment . 176.3.4 Raw materials and components 176.3.5 Product testing and evaluation . 176.3.6 Non-conforming

17、products . 176.4 Inspection of a consignment of finished products . 177 Test methods . 18Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EN 12467:2012 (E) 3 7.1 G

18、eneral . 187.2 Dimensional and geometrical tests . 187.2.1 Preparation of specimen. 187.2.2 Apparatus . 187.2.3 Procedure . 187.2.4 Expression and interpretation of results 217.3 Tests for physical performance and characteristics . 217.3.1 Apparent density . 217.3.2 Mechanical characteristics - Bend

19、ing strength Modulus of elasticity (Bending modulus) 227.3.3 Water impermeability 267.3.4 Water vapour permeability . 277.3.5 Warm water 277.3.6 Soak-dry . 287.3.7 Moisture movement test . 297.4 Tests for climatic performance 307.4.1 Freeze-thaw 307.4.2 Heat-rain . 317.5 Test for reaction to fire pe

20、rformance 337.5.1 Sheets satisfying the requirements for the fire reaction Class A1 without the need for testing . 337.5.2 Other sheets . 338 Marking, labelling and packaging 40Annex A (normative) Consignment inspection sampling . 41Annex B (normative) Statistical method for determining the correspo

21、nding wet values or revised dry specifications for the MOR when carrying out the dry method of test or when tested prior to coating for quality control purposes . 42B.1 Procedure . 42B.2 Determination of the correlation between the results of testing wet and dry specimens . 42B.3 Determination of th

22、e regression line . 43B.4 Determination of a value for wet testing from an obtained value for dry testing . 43B.5 Determination of the minimum value specified for dry testing xstdcorresponding to the minimum value specified for wet testing in this document ystd44Annex C (normative) Test method for t

23、he determination of moisture movement characteristic of fibre-cement sheets . 45C.1 General . 45C.2 Principle 45C.3 Apparatus . 45C.4 Specimen preparation . 45C.5 Test procedure . 45C.6 Calculation of results 46C.7 Test report 46Annex ZA (informative) Clauses of this European Standard addressing the

24、 provisions of the EU Construction Products Directive . 47ZA.1 Scope and relevant characteristics . 47ZA.2 Procedure for the attestation of conformity of fibre cement flat sheets . 48ZA.2.1 Systems of attestation of conformity 48ZA.2.2 EC Declaration of conformity . 51ZA.3 CE marking . 52Bibliograph

25、y 54Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EN 12467:2012 (E) 4 Foreword This document (EN 12467:2012) has been prepared by Technical Committee CEN/TC 128

26、 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and conflict

27、ing national standards shall be withdrawn at the latest by March 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document s

28、upersedes EN 12467:2004. In comparison with the previous edition, the following sections have been changed or added: 3.9, 3.10, 4, 5.1.1, 5.4.3, 5.4.4, Table 7, Table 8, 7.3.2, 7.3.2.4.2, 7.3.3.3, 7.3.3.4, 7.3.7, 7.5.2.2 and Annex C. Annex ZB concerning the EC Directive 76/769/EEC has been deleted.

29、This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. A dist

30、inction has been made between product appraisal (type tests) and factory production control requirements (acceptance tests). The performance of a building part constructed with these sheets depends not only on the properties of the product as required by this document, but also on the design, constr

31、uction and installation of the component as a whole in relation to the environment and conditions of use. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croa

32、tia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and t

33、he United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EN 12467:2012 (E) 5 1 Scope This European Standard specifies the technical requirements and est

34、ablishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses: internal wall and ceiling finishes; external wall and ceiling finishes. Products cov

35、ered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays. This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1. This European Standard does not cover sheets for fire

36、 protection purposes. This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets. 2 Normative references The following documents, in whole or in part, are normatively referenced in this

37、 document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 197-1, Cement Part 1: Composition, specifications and conformity criteria for common

38、 cements EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN 13823, Reaction to fire tests for building products Building products excluding floorings exposed to the thermal attack by a single burning it

39、em EN ISO 1716, Reaction to fire tests for building products Determination of the gross heat of combustion (calorific value) (ISO 1716) EN ISO 12572, Hygrothermal performance of building materials and products Determination of water vapour transmission properties (ISO 12572) ISO 2602, Statistical in

40、terpretation of test results Estimation of the mean Confidence interval ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection ISO 3951-1, Sampling procedures for inspection by variables Part 1: Specif

41、ication for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. Copyright European Committee for Standardiz

42、ation Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12467:2012EN 12467:2012 (E) 6 3.1 acceptance test test to establish whether a batch of sheets conforms to a specification and which is performed on samples drawn eithe

43、r from continuous production or from a consignment Note 1 to entry: Test methods, specifications and limit values are specified in this document. Sampling levels and acceptance criteria are specified in 6.3.2. 3.2 initial type test test carried out to demonstrate conformity with the requirements of

44、this document or for the approval of a new product and/or when a fundamental change is made in formulation and/or method of manufacture, the effects of which cannot be predicted on the basis of previous experience Note 1 to entry: The test is performed on the as delivered product, but is not require

45、d for each production batch. 3.3 acceptable quality level (AQL) quality level which in a sampling plan corresponds to a specified, relatively high probability of acceptance Note 1 to entry: It is the maximum percent defective (or maximum number of defects per 100 units) that for purposes of sampling

46、 inspection can be considered satisfactory as a process average. Note 2 to entry: A sampling scheme with an AQL of 4 % means that batches containing up to 4 % defective items have a high probability of acceptance. 3.4 apparent density density based on the external dimensions of the sample to calcula

47、te the volume Note 1 to entry: This is an average density of material and pores. 3.5 as delivered same condition as the producer intends to supply the product after completing all aspects of the process including maturing and, when appropriate, painting 3.6 upper face face normally exposed 3.7 under face reverse of upper face 3.8 textured sheets sheets which have a relief pattern embossed or applied as a coating on their upper face before delivery 3.9 NT type of fibre-cement flat sheets which cover products made using a non-asbestos technology 3.10 ambient laboratory conditions ambien