BS EN 12560-1-2001 Flanges and their joints - Gaskets for Class-designated flanges - Non-metallic flat gaskets with or without inserts《法兰及其接头 标示等级的法兰衬垫 有或无插孔的非金属水平衬垫》.pdf

1、BRITISH STANDARD BS EN 12560-1:2001 Flanges and their joints Gaskets for Class-designated flanges Part 1: Non-metallic flat gaskets with or without inserts The European Standard EN 12560-1:2001 has the status of a British Standard ICS 23.040.80 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED B

2、Y COPYRIGHT LAWBS EN 12560-1:2001 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 March 2001 BSI 03-2001 ISBN 0 580 37050 X National foreword This British Sta

3、ndard is the official English language version of EN 12560-1:2001. It supersedes BS 7076-1:1989 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/2, Jointing material and compounds, which has the responsibility to: A list of organizations represente

4、d on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence I

5、ndex”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself

6、 confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them i

7、n the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 17 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEA

8、N STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12560-1 January 2001 ICS 23.040.80 English version Flanges and their joints Gaskets for Class-designated flanges Part 1: Non-metallic flat gaskets with or without inserts Brides et leurs assemblages Joints pour les brides dsignes Class Partie 1: Joints p

9、lats non mtalliques avec ou sans insert Flansche und ihre Verbindungen Dichtungen fr Flansche mit Class-Bezeichnung Teil 1: Flachdichtungen aus nichtmetallischem Werkstoff mit oder ohne Einlagen This European Standard was approved by CEN on 28 December 2000. CEN members are bound to comply with the

10、CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to

11、 any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.

12、CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NOR

13、MALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12560-1:2001 EPage 2 EN 12560-1:2001 BSI 03-2001 Contents Page Foreword 3 Introdu

14、ction . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 3.1 DN 5 3.2 NPS 5 3.3 Class 5 4 Designations 6 4.1 Range of Class designations. 6 4.2 Range of gasket sizes 6 4.3 Gasket types. 6 4.4 Information to be supplied by the purchaser 6 5 Gasket designs and materials . 7 6 Gasket ty

15、pes. 7 7 Range of nominal sizes 11 8 Dimensions 11 8.1 Thickness . 11 8.2 Diameters . 12 8.3 Tolerances 14 9 Marking. 14 Annex A (informative) A-deviations. 15Page 3 EN 12560-1:2001 BSI 03-2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 74, Flanges and their join

16、ts, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2001, and conflicting national standards shall be withdrawn at the latest by July 2001. According

17、to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spa

18、in, Sweden, Switzerland and the United Kingdom. The annex A is informative and contains “A-deviations”.Page 4 EN 12560-1:2001 BSI 03-2001 Introduction EN 12560 consists of seven parts: Part 1: Non-metallic flat gaskets with or without inserts. Part 2: Spiral wound gaskets for use with steel flanges.

19、 Part 3: Non-metallic PTFE envelope gaskets. Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges. Part 5: Metallic ring-joint gaskets for use with steel flanges. Part 6: Kammprofile gaskets for use with steel flanges. Part 7: Covered metal jacketed gas

20、kets for use with steel flanges. The terminology and definitions in this standard are in accordance with those given in ISO standards. WARNING: Gaskets made to this standard may contain asbestos. Materials containing asbestos may be subject to legislation that requires precautions to be taken when h

21、andling them to ensure that they do not constitute a hazard to health (see annex A). Attention is drawn to the relevant EC directives.Page 5 EN 12560-1:2001 BSI 03-2001 1 Scope This European Standard specifies the dimensions, types, designation and marking of non-metallic flat gaskets, with or witho

22、ut insertion, for use with flanges in accordance with prEN 1759-1:2000, prEN 1759-3:1994 and prEN 1759-4:1994, for Class designations Class 150, Class 300, Class 600 and Class 900 for nominal sizes DN 15 to DN 600. NOTE: Dimensions of other types of gaskets for use with flanges complying with prEN 1

23、759-1:2000, prEN 1759-3:1994 and prEN 1759-4:1997 are given in prEN 12560-2:2000, prEN 12560-3:2000, prEN 12560-4:2000,prEN 12560-5:2000, prEN 12560-6:2000 and prEN 12560-7:2000. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publicati

24、ons. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. F

25、or undated references the latest edition of the publication referred to applies (including amendments). prEN 1759-1:2000 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 1: Steel flanges, nominal pipe sizes NPS to NPS 24. prEN 1759-3:1994 F

26、langes and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 3: Copper alloy and composite flanges. prEN 1759-4:1997 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 4: Aluminium alloy flanges.

27、 EN ISO 6708 Pipework components Definition and selection of DN (nominal size) (ISO 6708:1995). 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply: 3.1 DN see EN ISO 6708 3.2 NPS see prEN 1759-3:1994 3.3 Class see prEN 1759-3:1994Page 6 EN 1

28、2560-1:2001 BSI 03-2001 4 Designations 4.1 Range of Class designations Gaskets shall be designated as suitable for use with one or more of the following Class designations of flange: Class 150; Class 300; Class 600; Class 900. 4.2 Range of gasket sizes Gasket nominal sizes shall be designated in acc

29、ordance with the ranges specified in Tables 1, 2 and 3. 4.3 Gasket types Gasket types as defined in clause 6 and illustrated in Figures 1 and 2 shall be designated as: Type FF; Type IBC; Type TG; Type SR. 4.4 Information to be supplied by the purchaser The following information shall be supplied by

30、the purchaser when ordering gaskets: a) the number and part of this European Standard, i.e. EN 12560-1; b) gasket type designation (see 4.3); c) nominal size (see Tables 2 or 3, as appropriate); d) Class designation (see Tables 2 or 3, as appropriate); e) thickness (see 8.1); f) material(s) (see cla

31、use 5). Additional information that should be supplied by the purchaser: g) expected operating conditions for which the gasket will be used and whether the gasket is required for use with water intended for human consumption (see clause 5).Page 7 EN 12560-1:2001 BSI 03-2001 NOTE: Before ordering a g

32、asket it is recommended that the selection of the gasket type, material and thickness should be made in consultation with the gasket supplier. The selection of gasket material type and thickness should take into account the fluid, the operating conditions, the properties of the gasket material, the

33、type and surface finish of the flange facing and the flange bolt loading. EXAMPLE: A gasket according to EN 12560-1, full face type (type FF), of nominal size DN 100, Class 150, 2 mm thickness in expanded graphite, shall be designated as follows: Gasket EN 12560-1 FF DN 100 Class 150 2 mm expanded g

34、raphite. 5 Gasket designs and materials Gaskets shall be manufactured in a single material or combination of materials and shall be one of the following designs: a) single flat sheet; or b) laminated ply; or c) moulded. NOTE 1: The selection of the gasket material should take into account the fluid,

35、 the operating conditions, the properties of the gasket material, the type and surface finish of the flange facing and the flange bolt loading. It is recommended that selection of gaskets for any particular application is made in consultation with the gasket supplier (see 4.4). Where gaskets come, o

36、r are likely to come, into contact with water intended for human consumption, the materials shall comply with relevant national regulations. NOTE 2: The purchaser should indicate on the enquiry and/or order if gaskets are to be used with water intended for human consumption (see 4.4). It should be n

37、oted that the national regulations of both the country of origin and the country of use may be considered relevant. 6 Gasket types Gaskets shall be one of the following types: a) Full face type gasket (designation: type FF) for use with type A (flat face) or type B (raised face) flange facings see F

38、igures 1 a) and 2 a); b) Inside bolt circle type gasket (designation: type IBC) for use with type A (flat face) or type B (raised face) flange facings see Figures 1 b), 2 b), 2 c) and 2 d); c) Tongue and groove type gasket (designation: type TG) for use with type C/D (tongue/groove) flange facings s

39、ee Figures 1 c) and 2 b), 2 c) and 2 d); d) Spigot and recess type gasket (designation type SR), for use with type E/F (spigot/recess) flange facings see Figures 1 d); 2 b), 2 c) and 2 d); NOTE 1: The types of flange facings are specified in prEN 1759-1:2000, prEN 1759-3:1994 and prEN 1759-4:1997 an

40、d for information, the facings are shown in Figure 3. NOTE 2: The selection of gasket type should take into account the fluid, the operating conditions, the properties of the gasket material, the type and surface finish of the flange facing and the flange bolt loading. It is recommended that selecti

41、on of gasket type for any particular application is made in consultation with the gasket supplier (see 4.4).Page 8 EN 12560-1:2001 BSI 03-2001 a) Type A flange facings with Type FF gasket b) Type B flange facings with Type IBC gasket c) Type C/D flange facings with Type TG gasket d) Type E/F flange

42、facings with Type SR gasket Figure 1 Types of flange facings with gasketsPage 9 EN 12560-1:2001 BSI 03-2001 This figure illustrates the arrangement Key but not necessarily the correct number 1 Outside diameter of bolt holes. Refer to the relevant table 2 Inside diameter for the actual number of bolt

43、 holes. Key 1 Outside diameter 2 Bolt circle diameter 3 Hole diameter b) Type IBC gasket (for type A and type B flange facings). Type TG gasket (for type C/D flange facings). Type SR gasket (for type E/F flange facings). Key Key 1 Inside diameter 1 Inside diameter a) Type FF gasket (for types A and

44、B flange c) Typical rubber gasket with fabric facings) insertion Key 1 Inside diameter d) Typical rubber gasket with metallic insertion Figure 2 Gasket dimensionsPage 10 EN 12560-1:2001 BSI 03-2001 Type A Flat face Type C Tongue Type B Raised face Type D Groove Type E Spigot Type F RecessFigure 3 Fl

45、ange facing typesPage 11 EN 12560-1:2001 BSI 03-2001 7 Range of nominal sizes The ranges of nominal sizes of gaskets for the various Class designations shall be as given in Table 1 for the different gasket types. Table 1 Range of gasket nominal sizes Gasket type a Class Type FF Type IBC Type TG Type

46、 SR For dimensions refer to table number DN range 150 2 15 to 600 15 to 600 - - 300 3 - 15 to 600 15 to 600 15 to 600 600 3 - 15 to 600 15 to 600 15 to 600 900 3 - 15 to 600 15 to 600 15 to 600 aSee clause 6. 8 Dimensions 8.1 Thickness NOTE: The selection of gasket thickness should take into account

47、 the fluid, the operating conditions, the properties of the gasket material, the type and surface finish of the flange facing and the flange bolt loading. It is recommended that selection of gasket thickness for any particular application is made in consultation with the gasket supplier (see 4.4).Pa

48、ge 12 EN 12560-1:2001 BSI 03-2001 8.2 Diameters The diameters of Class 150 designated gaskets shall be as given in Table 2. The diameters of Class 300, 600 and 900 gaskets shall be as given in Table 3. In the case of gaskets with an inner metallic insertion, the gasket inside diameter shall be to th

49、e inside of the insertion see Figure 2 d). Table 2 Dimensions of gaskets for Class designation 150 flanges Nominal size Gasket inside diameter Type IBC gasket outside diameter Type FF gasket Outside diameter Holes Bolt circle diameter Number Diameter b DN NPS a mm mm mm mm in mm 15 22 47,5 89 4 15,9 60,3 20 27 57,0 98 4 15,9 69,8 25 1 34 66,5 108 4 15,9 79,4 32 1 43 76,0 117 4 15,9 88,9 40 1 49 85,5 127 4 15,9 98,4 50 2 61 104,5 152 4 19,0 12