BS EN 12560-4-2001 Flanges and their joints - Gaskets for Class-designated flanges - Corrugated flat or grooved metallic and filled metallic gaskets for use with steel flanges《法兰及其.pdf

1、BRITISH STANDARD BS EN 12560-4:2001 Flanges and their joints Gaskets for Class-designated flanges Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges The European Standard EN 12560-4:2001 has the status of a British Standard ICS 23.040.80 NO COPYING WI

2、THOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 12560-4:2001 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 March 2001 BSI 03-2001 ISBN 0 580

3、37049 6 National foreword This British Standard is the official English language version of EN 12560-4:2001. It supersedes BS 7076-4:1989 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/2, Jointing material and compounds, which has the responsibil

4、ity to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled

5、 “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance

6、with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and E

7、uropean developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 13 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since

8、 publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12560-4 January 2001 ICS 23.040.80 English version Flanges and their joints Gaskets for Class-designated flanges Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges

9、 Brides et leurs assemblages Joints pour les brides dsignes Class Partie 4: Joints mtalliques onduls, plat ou stris et joints mtalloplastiques pour utilisation avec des brides en acier Flansche und ihre Verbindungen Dichtungen fr Flansche mit Class-Bezeichnung Teil 4: Dichtungen aus Metall mit gewel

10、ltem, flachem oder gekerbtem Profil fr Stahlflansche This European Standard was approved by CEN on 28 December 2000. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an

11、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by t

12、ranslation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland

13、, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any fo

14、rm and by any means reserved worldwide for CEN national Members. Ref. No. EN 12560-4:2001 EPage 2 EN 12560-4:2001 BSI 03-2001 Contents Page Foreword. 2 Introduction 4 1 Scope. 5 2 Normative references 5 3 Terms and definitions. 5 3.1 DN 5 3.2 NPS 5 3.3 Class 5 4 Designations . 6 4.1 Range of Class d

15、esignations 6 4.2 Range of gasket sizes 6 4.3 Gasket types and designs. 6 4.4 Information to be supplied by the purchaser 6 5 Gasket designs 7 6 Gasket types8 7 Dimensions 8 7.1 Diameters 8 7.2 Thickness 10 8 Marking 11 Annex A (informative) A-deviations 12Page 3 EN 12560-4:2001 BSI 03-2001 Foreword

16、 This European Standard has been prepared by Technical Committee CEN/TC 74, Flanges and their joints, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July

17、2001, and conflicting national standards shall be withdrawn at the latest by July 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland

18、, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The annex A is informative and contains “A-deviations”.Page 4 EN 12560-4:2001 BSI 03-2001 Introduction EN 12560 consists of seven parts: Part 1: Non-metal

19、lic flat gaskets with or without inserts Part 2: Spiral wound gaskets for use with steel flanges Part 3: Non-metallic PTFE envelope gaskets Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges Part 5: Metallic ring-joint gaskets for use with steel flang

20、es Part 6: Kammprofile gaskets for use with steel flanges Part 7: Covered metal jacketed gaskets for use with steel flanges The terminology and definitions in this standard are in accordance with those given in ISO Standards. WARNING Gaskets made to this standard may contain asbestos. Materials cont

21、aining asbestos may be subject to legislation that requires precautions to be taken when handling them to ensure that they do not constitute a hazard to health (see annex A). Attention is drawn to relevant EC directives.Page 5 EN 12560-4:2001 BSI 03-2001 1 Scope This European Standard specifies the

22、dimensions and marking of IBC (inside bolt circle) type corrugated, flat or grooved metallic and filled metallic gaskets for use in conjunction with flanges complying with prEN 1759-1:2000 for Class 150, 300, 600, 900 and 1500 for nominal sizes DN 15 to DN 600, and for Class 2 500 for nominal size D

23、N 15 to DN 300. NOTE Dimensions of other types of gaskets for use with flanges complying with prEN 1759-1:2000, prEN 1759-3:1994 and prEN 1759-4:1997 are given in prEN 12560-1:2000, prEN 12560-2:2000, prEN 12560-3:2000, prEN 12560-5:2000, prEN 12560-6:2000 and prEN 12560-7:2000. 2 Normative referenc

24、es This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these

25、publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). prEN 1759-1:2000 Flanges and their joints Circular flanges for pipes, valves, fittings and acce

26、ssories, Class designated Part 1: Steel flanges prEN 1759-3:1994 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 3 :Copper alloy flanges prEN 1759-4:1997 Flanges and their joints Circular flanges for pipes, valves, fittings, and accessorie

27、s, Class designated Part 4: Aluminium alloy flanges EN ISO 6708 Pipework components Definition and selection of DN (nominal size) (ISO 6708:1995) 3 Terms and definitions For the purposes of this European Standard the following terms and definitions apply: 3.1 DN see EN ISO 6708 3.2 NPS see prEN 1759

28、-3:1994 3.3 Class see prEN 1759-3:1994Page 6 EN 12560-4:2001 BSI 03-2001 4 Designations 4.1 Range of Class designations Gaskets shall be designated or suitable for use with one or more of the following Class designations of flange: Class 150; Class 300; Class 600; Class 900; Class 1 500; Class 2 500

29、. 4.2 Range of gasket sizes Gasket nominal sizes shall be designated in accordance with the ranges specified in Table 1. 4.3 Gasket types and designs Gasket types and designs, as defined in clause 6 and illustrated in Figure 1, shall be designated as: Self-centering: With centering ring: SC/A CR/A S

30、C/B CR/B SC/C CR/C SC/D CR/D SC/E CR/E 4.4 Information to be supplied by the purchaser The following information should be supplied by the purchaser when ordering gaskets: a) the number and Part of this European Standard, i.e. EN 12560-4; b) gasket type (see clause 6); c) gasket design (see clause 5

31、); d) nominal size (see Table 1); e) Class designation (see Table 1);Additional information that should be supplied by the purchaser: f) expected operating conditions for which the gasket will be used. NOTE Before ordering a gasket it is recommended that the selection of the gasket design and type s

32、hould be made in consultation with the gasket supplier. The selection of gasket design and type should take account of the operating conditions, the properties of the gasket material(s), type and surface finish of the flange facing and the flange bolt loading. EXAMPLE A gasket according to EN 12560-

33、4, with centering ring (type S6) and corrugated metal design (design B) of nominal size DN 100, Class 150, shall be designated as follows : Gasket EN 12560-4 SC/B DN 100 Class 150.Page 7 EN 12560-4:2001 BSI 03-2001 5 Gasket designs Gaskets shall be one of the designs shown in Figure 1. c) Flat metal

34、 jacketed with filler (Design -/C) a) Corrugated metal, with filler (top) corrugated metal jacket with filler (bottom) (Design -/A) d) Grooved metal (Design -/D) b) Corrugated metal (Design-/B) e) Solid flat metal (Design -/E) Figure 1 Designs of corrugated, flat or grooved metallic and filled metal

35、lic gasketsPage 8 EN 12560-4:2001 BSI 03-2001 6 Gasket types Gaskets are IBC (inside bolt circle) type and shall be for use with type A (flat face) or type B (raised face) flange facings (see Figure 2) and shall be one of the following types: a) self-centering, Type SC/ (see 4.3); b) incorporating a

36、 centering ring, Type CR/ (see 4.3). NOTE Type A and type B flange facings are shown in prEN 1759-1:2000. a) Self-centering b) with centering ring NOTE Type B, raised face flange facings are shown. Figure 2 Gaskets for type A or type B flange facings 7 Dimensions 7.1 Diameters The dimensions of corr

37、ugated, flat or grooved metallic and filled metallic gaskets shall be as given in Table 1.Page 9 EN 12560-4:2001 BSI 03-2001 Table 1 Dimensions of corrugated, flat or grooved metallic and filled metallic gaskets Nominal size Gasket inside diameter min. Gasket or centering ring outside diameter Class

38、 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500 DN NPS a mm mm mm mm mm mm mm 15 22 47,6 54,0 54,0 63,5 63,5 69,9 20 27 57,2 66,7 66,7 69,9 69,9 76,2 25 1 34 66,7 73,0 73,0 79,4 79,4 85,7 32 1 43 76,2 82,6 82,6 88,9 88,9 104,8 40 1 49 85,7 95,3 95,3 98,4 98,4 117,5 50 2 61 104,8 111,1 111

39、,1 142,9 142,9 146,1 65 2 73 123,8 130,2 130,2 165,1 165,1 168,3 80 3 89 136,5 149,2 149,2 168,3 174,6 196,9 100 4 115 174,6 181,0 193,7 206,4 209,6 235,0 125 5 141 196,9 215,9 241,3 247,7 254,0 279,4 150 6 169 222,3 250,8 266,7 288,9 282,6 317,5 200 8 220 279,4 308,0 320,7 358,8 352,4 387,4 250 10

40、273 339,7 362,0 400,1 435,0 435,0 476,3 300 12 324 409,6 422,3 457,2 498,5 520,7 549,3 350 14 356 450,9 485,8 492,1 520,7 577,9 - 400 16 407 514,4 539,8 565,2 574,7 641,4 - 450 18 458 549,3 596,9 612,8 638,2 704,9 - 500 20 508 606,4 654,1 682,6 698,5 755,7 - 600 24 610 717,6 774,7 790,6 838,2 901,7

41、- aFor information only. For flat metal gaskets or filled metal jacketed gaskets the inner diameters of the gaskets shall be as given in Table 2, the outer dimensions remain as shown in Table 1.Page 10 EN 12560-4:2001 BSI 03-2001 Table 2 Gasket inside diameter for flat metal gaskets or filled metal

42、jacketed gaskets Gasket inside diameter Nominal size Designation Class 150 Class 600 Class 300 Class 900 Class 1 500 Class 2 500 DN NPS a mm mm 15 22 22 20 29 29 25 1 38 38 32 1 48 48 40 1 57 54 50 2 75 73 65 2 90 86 80 3 113 108 100 4 141 132 125 5 165 152 150 6 196 190 200 8 253 238 250 10 294 286

43、 300 12 356 343 350 14 382 375 400 16 434 425 450 18 500 498 500 20 540 533 600 24 647 641 afor information only 7.2 Thickness For jacketed gaskets the following specifications shall apply: a) The jacket metal thickness shall be a minimum of 0,38 mm. b) The filler thickness shall be a minimum of 1,5

44、 mm. NOTE The selection of the gasket should take into account the fluid, the operating conditions, the properties of the gasket materials, the type and surface finish of the flange facing and the flange bolt loading. It is recommended that selection of gaskets for any particular application is made

45、 in consultation with the gasket supplier.Page 11 EN 12560-4:2001 BSI 03-2001 8 Marking Gaskets shall be marked either individually or on the packaging containing the gaskets, or by agreement between supplier and purchaser, on the packaging containing each individual gasket, with the following infor

46、mation: a) the number and part of this European Standard, i.e. EN 12560-4; b) gasket type/design designation (see 4.3); c) the nominal size (see Table 1); d) the Class designation (see Table 1); e) materials; f) manufacturers name or trademark. EXAMPLE EN 12560-4 SC/A DN 100 Class 600 XXX AAA/BBB.Pa

47、ge 12 EN 12560-4:2001 BSI 03-2001 Annex A (informative) A-deviations This European Standard is mandated under the Council Directive on the approximation of the laws of the Member States concerning pressure equipment. A-deviation: National deviation due to regulations, the alteration of which is for

48、the time being outside the competence of the CEN/CENELEC member. NOTE (from CEN/CENELEC) IR Part 2, 3.1.9): Where standards fall under EC Directives, it is the view of the Commission of the European Communities (OJ No G 59, 9.3.1982) that the effect of the decision of the Court of Justice in case 81

49、5/79 Cremonini/Vrankovich (European Court Reports 1980, p. 3583) is that compliance with A-deviations is no longer mandatory and that the free movement of products complying with such a standard should not be restricted except under the safeguard procedure provided for in the relevant Directive. A-deviations in an EFTA country are valid instead of the relevant provisions of the European Standard in that country until they have been removed.