1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12585:1999 The Euro
2、pean Standard EN 12585:1998 has the status of a British Standard ICS 23.040.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Glass plant, pipeline and fittings Pipeline and fittings DN 15 to 1 000 Compatibility and interchangeabilityBS EN 12585:1999 This British Standard, ha
3、ving been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 September 1999 BSI 09-1999 ISBN 0 580 32095 2 Amendments issued since publication Amd. No. Date Comments National foreword This British
4、 Standard is the English language version of EN 12585:1998. It supersedes BS 2598-3:1980 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PSE/13, Glass piping, which has the responsibility to: aid enquirers to understand the text; present to the respon
5、sible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on req
6、uest to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of
7、the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. S
8、ummary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.CEN European Committee for Standardization Comite Europe en de Normalisation
9、 Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12585:1998 E EUROPEAN STANDARD EN 12585 NORME EUROPE ENNE EUROPA ISCHE NORM November
10、1998 ICS 23.040.50; 71.120.01 Descriptors: glassware, glass, borosilicate glass, glass tubes, pipe fittings, glass fittings, dimensions, compatibility, interchangeability English version Glass plant, pipeline and fittings Pipeline and fittings DN 15 to 1 000 Compatibility and interchangeability Appa
11、reillage, tuyauterie et raccords en verre Tuyauterie et raccords DN 15 a DN 1 000 Compatabilite et interchangeabilite Apparate, Rohrleitungen und Fittings aus Glas Rohrleitungen und Fittings DN 15 bis 1 000 Verbindbarkeit und Austauschbarkeit This European Standard was approved by CEN on 8 November
12、1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtaine
13、d on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secreta
14、riat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN
15、 12585:1998 BSI 09-1999 Foreword This European Standard has been prepared by Technical Committee CEN/CS, the Secretariat of which is held by DIN (Ko ln). This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the late
16、st by May 1999, and conflicting national standards shall be withdrawn at the latest by May 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark
17、, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Material and working conditions 3 5 Basic dimensions 3 6 Mating req
18、uirements 3 7 Essential dimensions for interchangeability 4 8 Marking 6 Figure 1 Length of components with plain buttress ends and annular zone required for mating plain buttress ends with reference to diameters d9 and d0 4 Figure 2 Length of components with spherical buttress ends with reference to
19、 diameter d 0 5 Figure 3 Reducer 5 Figure 4 458 bend 6 Figure 5 908 bend 6 Figure 6 Equal tee 6 Figure 7 Cross 7 Figure 8 Angle valve 7 Table 1 Dimensions for compatibility of plain and spherical buttress ends 4 Table 2 Minimum possible deviation from alignment 4 Table 3 Length and tolerances on len
20、gth 4 Table 4 Permissible bow of pipe sections 5 Table 5 Lengths and tolerances of reducers 5 Table 6 Lengths and tolerances of 908 bends, equal tees, crosses and angle valves 6 Table 7 Lengths and tolerances of 458 bends 6Page 3 EN 12585:1998 BSI 09-1999 1 Scope This standard specifies the essentia
21、l requirements for compatibility and interchangeability of borosilicate glass plant, piping and fittings from DN 15 to DN 1 000. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the
22、appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the
23、publication referred to applies. EN 1595, Pressure equipment made from borosilicate glass 3.3 General rules for design, manufacture and testing. ISO 3585, Borosilicate glass 3.3 Properties. 3 Definitions For the purposes of this standard the following definitions apply. 3.1 plant complete installati
24、on consisting of components, piping and fittings which are connected by flange couplings 3.2 piping complete assembly consisting of pipe sections and fittings which are connected by flange couplings 3.3 pipe section straight length of pipe fitted with buttress ends 3.4 buttress end specially shaped
25、end of a glass component, the joint face being either plain (flat or with gasket location groove) or spherical (convex or concave) 3.5 fittings items such as spacers, reducers, bends, tees, crosses, and valves used in conjunction with pipe sections within piping 3.6 flange coupling complete assembly
26、 of backing flanges, inserts, gaskets, and the appropriate bolts and nuts for connecting two buttress ends 3.7 adaptor flange special backing flange for coupling buttress ends of different design (see 6.2) 3.8 insert sleeve or ring between the buttress end and the backing flange 4 Material and worki
27、ng conditions 4.1 Material properties The glass parts referred to in this specification shall be manufactured from borosilicate glass 3.3, which is resistant to both heat and chemical attack. Its properties are specified in ISO 3585. 4.2 Working conditions The maximum allowable temperatures and pres
28、sures of installed systems shall not exceed those recommended by the manufacturer. There may be further limits, such as temperature differences and rates of heating and cooling, where reference shall be made to the manufacturers recommendations. 5 Basic dimensions 5.1 Nominal sizes (DN) The nominal
29、sizes DN are: 15, 25, 40, 50, 80, 100, 150, 200, 225, 300, 400, 450, 600, 800, 1 000. 5.2 Length All lengths of pipe sections size DN 15 to 150 shall be dimensioned in multiples of 25 mm. The length L: of components with plain buttress ends is the distance between the joint faces (see Figure 1); of
30、components with spherical buttress ends is the distance between the diameters d 0 (see Figure 2). 5.3 Wall thickness The required wall thicknesses shall be determined in accordance with EN 1595. 6 Mating requirements 6.1 Components with plain and spherical buttress ends In order to ensure the compat
31、ibility of components with plain and spherical buttress ends, the dimensions given in Table 1 shall be adhered to. 6.2 Adaptor flanges Because of the availability of glass components with different buttress end forms, backing flanges supplied by manufacturers of glass plant differ in shape, pitch ci
32、rcle diameter and number and diameter of bolt holes. To ensure that these various forms of buttress end can be bolted together, an adaptor flange shall be used. 6.3 Gaskets For sealing between spherical buttress ends of different shapes, the gasket for the concave buttress end shall be used. For pla
33、in buttress ends a gasket with a diameter within the annular mating zone shall be used (see Figure 1 and Table 1). Where one of the buttress ends has a gasket location groove the gasket appropriate to the grooved buttress end shall be used.Page 4 EN 12585:1998 BSI 09-1999 Table 1 Dimensions for comp
34、atibility of plain and spherical buttress ends DN 15 25 40 50 80 100 150 200 225 300 400 450 600 800 1 000 r radius of spherical buttress end mm 18 25 40 50 80 100 150 d 0 reference diameter of spherical buttress end mm 21 34 50 62 90 118 170 d9 max. 21 31 46 58 87 112 165 220 235 313 435 479 630 85
35、6 1 035 d0 min. diameter of annular mating zone for plain buttress end mm 24 36 51 64 95 125 174 230 250 330 460 505 650 886 1 065 1) DN Figure 1 Length of components with plain buttress ends and annular zone required for mating plain buttress ends with reference to diameters d9 and d0 6.4 Alignment
36、 of coupled spherical piping and fittings The spherical end pipe sections and fittings shall allow a deviation between the axes of two components fitted together of not less than the angular values given in Table 2. Table 2 Minimum possible deviation from alignment DN 15 25 40 50 80 100 150 Angle 38
37、 38 38 38 38 28 1,58 7 Essential dimensions for interchangeability 7.1 Tolerances on length The length and tolerances on length L of straight pipe sections and components shall be as given in Table 3. Table 3 Length and tolerances on length DN Length L mm # 300 400 500 700 1 000 1 500 2 000 3 000 15
38、 2 2 2 2 2 3 3 25 4 40 50 3 3 3 3 3 80 4 4 5 100 150 200 5 225 300 4 4 4 4 4 5 400 5 5 450 600 7 7 7 800 10 10 10 1 000Page 5 EN 12585:1998 BSI 09-1999 7.2 Permissible bow of pipe sections Bow is the longitudinal curvature of a pipe section expressed as the maximum deviation from the straight line c
39、onnecting two points at the extremities of its length within the buttress ends. The limits of permissible bow are given in Table 4. Table 4 Permissible bow of pipe sections DN Bow for length of pipe section mm # 500 700 1 000 1 500 2 000 3 000 15 22345 25 223458 40 223458 50 223568 80 223568 100 223
40、568 150 234671 0 7.3 Reducers The lengths and tolerances of reducers are given in Table 5. Figure 3 shows the reducer with plain buttress ends. For spherical buttress ends the length L is measured from the reference diameters d 0 (see Figure 2). Table 5 Lengths and tolerances of reducers DN 1 DN 2 L
41、 mm 25 15 100 2 40 15 100 2 25 100 2 50 15 100 3 25 100 3 40 100 3 80 25 125 3 40 125 3 50 125 3 100 25 150 3 40 150 3 50 150 3 80 150 3 150 25 200 3 40 200 3 50 200 3 80 200 3 100 200 3 1) 2) 3) Plug gauge DN Ring gauge Figure 2 Length of components with spherical buttress ends with reference to di
42、ameter d 0 1) 2) DN 2 DN 1 Figure 3 Reducer 7.4 Bends, tees, crosses and angle valves Lengths and tolerances of 908 bends, equal tees, crosses and angle valves are given in Table 6, dimensions of 458 bends are given in Table 7. The Figures 4 to 8 show such items with plain buttress ends. In the case
43、 of spherical buttress ends the length L is measured from the reference diameters d 0 (see Figure 2). NOTE 908 bends, equal tees, crosses and angle valves are interchangeable with each other because of the same length L.Page 6 EN 12585:1998 BSI 09-1999 8 Marking The glass components shall be marked
44、permanently with the name of the manufacturer or processor and the type of glass or brand name. Table 6 Lengths and tolerances of 908 bends, equal tees, crosses and angle valves DN L mm 15 50 2 25 100 2 40 150 2 50 150 3 80 200 3 100 250 3 150 250 3 Table 7 Lengths and tolerances of 458 bends DN L m
45、m 15 50 2 25 75 2 40 100 2 50 100 3 80 125 3 100 175 3 150 200 3 1) DN Figure 4 458 bend 1) DN Figure 5 908 bend 1) DN Figure 6 Equal teePage 7 EN 12585:1998 BSI 09-1999 1) DN Figure 7 Cross 1) DN Figure 8 Angle valveBS EN 12585:1999 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | |
46、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body
47、responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest
48、amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can
49、be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Ser
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1