BS EN 12772-2000 Footwear - Test methods for outsoles - Dimensional stability《鞋靴 外底的试验方法 尺寸稳定性》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12772:2000 The Euro

2、pean Standard EN 12772:1999 has the status of a British Standard ICS 61.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Footwear Test methods for outsoles Dimensional stabilityThis British Standard, having been prepared under the direction of the Sector Committee for Mater

3、ials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 February 2000 BSI 02-2000 ISBN 0 580 35617 5 BS EN 12772:2000 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard is the official English langua

4、ge version of EN 12772:1999. It supersedes BS 5131-2.10:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear and leather, which has the responsibility to: aid enquirers to understand the text; present to the responsible European commi

5、ttee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-refer

6、ences The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catal

7、ogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comp

8、rises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.(8523($167$1$5 1250(8523e(11( (8523b,6 or b) a travelling microscope or similar optical

9、device with scale. 4.5 Thickness gauge Thickness gauge, standing on a firm base and loaded with a dead weight such that the presser foot applies a pressure of 10 kPa 3 kPa. The gauge has a presser foot which is flat, circular and 10 mm 0,1 mm in diameter, as defined in ISO 4648. The gauge has a scal

10、e division of 0,01 mm. 5 Sampling and conditioning The test pieces to be tested are taken in accordance with prEN 13400:1998. All test pieces shall be conditioned in accordance with EN 12222, before testing for a minimum of 24 h. The test samples with the full thickness of the outsoles shall be test

11、ed. A minimum of three test pieces is necessary. 6 Test method 6.1 Test specimen piece Using a scalpel or other sharp knife (4.2) and a steel rule (4.1), cut the test specimens to the dimensions and tolerances given in Figure 1. Make two parallel reference cuts on the external surface not more than

12、0,5 mm deep across the full width of the test specimen on each side of it, 100 mm 5 mm apart for the larger test specimen and 50 mm 5 mm apart for the smaller test specimen.3DJH (1 %6, 6.2 Measurement before heat treatment (L 0 ) Measure to within 0,2 mm the distance between the reference cuts along

13、 the centreline. 6.3 Heat treatment Place the test specimens horizontally (supported in such a way as to ensure adequate air ventilation on all sides) in the oven (4.3) for 24 h 0,5 h at the temperature of 70 C 2 C. 6.4 Measurement after heat treatment (L) Remove the test specimen from the oven at t

14、he end of the period of heat treatment. Keep the test specimens for at least 30 min in a standard atmosphere. If the test specimens are bowed, hold them flat for measurement. If the measuring cuts have widened, take the point of the measurement as the centre of the cut. Measure to within 0,2 mm the

15、distance between these cuts along the centreline as described in Figure 1 using an appropriate device. 7 Expression of results For each test specimen, calculate the shrinkage of the distance between the reference cuts produced by the heat treatment and express this as a percentage of the original di

16、stance. The worst of the three values will be the result. Shrinkage S, in %, is to be calculated using the formula: - = / / / 6 where L 0 is the original distance between the reference cuts in millimetres, as recorded according to 6.2; L is the distance between the reference cuts after heat treatmen

17、t, in millimetres, as recorded according to 6.4.3DJH (1 %6, 8 Test report The test report shall include the following information: a) results, expressed in accordance with clause 7; b) dimensions (including thickness) of the test specimen; c) full description of the samples tested including commerci

18、al styles, codes, colours, nature, etc.; d) reference to this method of test; e) date of testing; f) any deviations from this test method; g) the age of the sample.3DJH (1 %6, Dimensions in mm Figure 1 - Long and short test specimens for shrinkage, showing dimensions and positions of reference cutsb

19、lankBS EN 12772:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

20、| | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment

21、 or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would

22、inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of

23、 standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have

24、been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also a

25、vailable which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these

26、and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Desig

27、ns and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, o

28、f necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.