BS EN 129202-1995 Specification for harmonized system of quality assessment for electronic components - Blank detail specification wirebound inductors with ceramic or ferrite core .pdf

1、BRITISH STANDARD BS EN 129202:1995 Harmonized system of quality assessment for electronic components Blank detail specification: Wirewound inductors with ceramic or ferrite core Assessment levelP The European Standard EN 129202:1994, together with its amendment A1:1995, has the status of a British S

2、tandardBSEN129202:1995 BSI 01-2000 ISBN 0 580 34081 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee EPL/51, Transformers, inductors, magnetic components and ferrite materials, upon which the following bodies were repres

3、ented: Federation of the Electronics Industry Ministry of Defence National Supervising Inspectorate (BSI PC) Amendments issued since publication Amd. No. Date CommentsBSEN129202:1995 BSI 01-2000 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 1292

4、02 5BSEN129202:1995 ii BSI 01-2000 National foreword This British Standard has been prepared by Technical Committee EPL/51. It is the English language version of EN129202:1994 Blank detail specification: Wirewound inductors with ceramic or ferrite core Assessment Level P, together with its amendment

5、 A1:1995, prepared by the German ONH under the Single Originator Procedure and published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). This standard lists the ratings, characteristics and inspection requirements which shall be includ

6、ed as mandatory requirements in any detail specification for this type of inductor. Detail specifications shall comply with the requirements of this Blank Detail Specification and BS CECC00111: Rule of Procedure 11. Specifications. Part 4:1991 Regulations for CECC Detail Specifications. The British

7、Standard which implements the CECC Rules of Procedure is BS9000 General requirements for a system of electronic components of assessed quality. Part 2:1996 Specification for the national implementation of the CECCsystem. A British Standard does not purport to include all the necessary provisions of

8、a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard EN 129000:1993 BS EN 129000:1996 Harmonized syst

9、em of quality assessment for electronic components. Generic Specification: Fixed RF wound inductors EN 129200:1994 BS EN 129200:1996 Harmonized system of quality assessment for electronic components: Sectional Specification: Fixed inductors with ceramic or ferrite core wound with copper wire for RF

10、circuits Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 11 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the

11、 inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 129202 July 1994 + A1 August 1995 Descriptors: Quality, electronic components, inductors English version Blank detail specification: Wirewound inductors with ceramic or ferrite core Assessment level P (includes amendment A1:199

12、5) Spcification particulire cadre: (nexiste pas en franais) Vordruck fr Bauartspezifikation: Drahtgewickelte Spulen mit Keramik- oder Ferritkern Gtebesttigungsstufe P (enthltnderung A1:1995) This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on1993-08-09. CENEL

13、EC members are bound to comply with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applic

14、ation to the General Secretariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Centra

15、l Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

16、CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to CENELEC members Ref. No. EN 129202:1994 + A1:1995 EEN12

17、9202:1994 BSI 01-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of

18、 the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate, of Conformity. The components produced under the System are thereby accepta

19、ble in all member countries without further testing. This specification was prepared by the German ONH under the Single Originator Procedure for approval and publication of CECC specifications (see RP11-V). The text of the draft based on document CECC(Secretariat)3266/01.93was submitted to the forma

20、l vote; together with the voting report, circulated as document CECC(Secretariat)3387/07.93, it was approved by CECC as EN129202 on9August1993. The following dates were fixed: Foreword This amendment was prepared by Working GroupCLC/TC CECC/WG DE. The text of the draft based on document CECC(Secreta

21、riat)3590 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3639, itwas approved as amendment A1 to EN129202:1994 on1994-12-28. The following dates were fixed: Contents Page Foreword 2 1 General data 5 2 Qualification approval and Inspection r

22、equirements 6 Table 1 5 Table 2 5 Table 3 Other characteristics 6 Table 4A Lot-by-lot inspection (Group A and B) 6 Table 4B Periodic tests (Group C) 7 latest date of announcement ofthe EN at national level (doa) 1993-11-08 latest date of publication ofan identical national standard (dop) 1994-05-08

23、latest date of withdrawal ofconflicting national standards (dow) 1995-05-08 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1995-10-24 latest date by which the national standards conflicting with the

24、amendment have to be withdrawn (dow) 1996-10-24EN129202:1994 BSI 01-2000 3 Identification of the detail specification (DS) and the component The first page of the DS should have the layout recommended on page3. The numbers in square brackets correspond to the indications to be completed thereunder:

25、1 The name of the National Standards Organization under whose authority the DS is published and, if applicable, the organization from whom the DS is available 2 The CECC symbol and the number allotted to the DS by the CECC General Secretariat 3 The number and year of publication of the EN generic an

26、d sectional specification as relevant; also national reference if different. 4 If different from the CECC number, the national number of the DS, date of issue and any further information required by the national system, together with any amendment numbers 5 A brief description of the component or ra

27、nge of components 6 Information on typical construction (where applicable) 7 An outline drawing with main dimensions which are of importance for interchangeability, and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an ann

28、ex to the DS, but 7 should always contain an illustration of the general outer appearance of the component 8 The level(s) of quality assessment covered by the DS 9 Reference data giving information on the most important properties of the component which allow comparison between the various component

29、 types intended for the same, of for similar, applications For 5 and 6 the text to be given in the DS should be suitable for an entry in CECC00200(Register of Approvals) and CECC00301(Register of CECC Specifications and Related Detail Specifications). Specification available from: CECC 29202-xxx 1 2

30、 4 ELECTRONIC COMPONENTS OF ASSESSED QUALITY DETAIL SPECIFICATION IN ACCORDANCE WITH: EN 129000:1993 EN 129200:1994 3 Outline and dimensions: (First angle projection) 7 DETAIL SPECIFICATION FOR WIREWOUND INDUCTORS WITH CERAMIC OR FERRITE CORE 5 TYPICAL CONSTRUCTION (Examples): 6 axial/radial termina

31、tions Assessment level P 8 9 QUICK REFERENCE DATA: Rated inductance range, inductance tolerance, rated current, climatic category, performance grade Information about manufacturer who have components qualified to this detail specification is availablein the current CECC 00200.4 blankEN129202:1994 BS

32、I 01-2000 5 1 General data 1.1 Recommended method of mounting The inductors are mounted by their terminations. See 1.3.2 of the sectional specification EN129200:1994. 1.2 Dimensions Table 1 1.3 Ratings and characteristics Table 2 1.4 Related documents 1.5 Marking The marking of the inductor and of t

33、he packing shall be in accordance with the requirements of 1.5 of the sectional specification EN129200:1994. NOTEThe details of the marking of the component and of packing shall be given in full in the detail specification. 1.6 Ordering information Orders for inductors covered by this specification

34、shall contain, in clear or in coded form, the following minimum information: 1) Rated inductance 2) Tolerance on rated inductance 3) Number of detail specification and case size reference 4) Packaging (bulk or taped; if taped, according to IEC286-1 or IEC286-2) Case size Dimensions (in mm) reference

35、 L d NOTEThe dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. Rated inductance range (See Table 2) Tolerance of rated inductance . Q-factor D.C. resistance (See Table 2) Self-resonant frequency Rated current Climatic category . Rated temperature . L R f L Q

36、min. f Q R max. f resmin. I R I CR Type of Core-material nH MHz MHz 7 MHz mA mA I CR : incremental current I R : rated current L R : rated inductance Q: quality factor R: D.C. resistance f L : measuring frequency for inductance f Q : measuring frequency for Q f res : resonant frequency Generic speci

37、fication:EN 129000:1993 Sectional specification:EN 129200:1994EN129202:1994 6 BSI 01-2000 1.7 Certified test records Required/not required 1.8 Additional information (not for inspection purpose) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional

38、 specification NOTEAdditions or increased requirements should be specified only when essential. Table 3 Other characteristics 2 Qualification approval and Inspection requirements 2.1 Procedures 2.1.1 For Qualification Approval the procedures shall be in accordance with 3.4 of the sectional specifica

39、tion EN129200:1994. 2.1.2 For Quality Conformance Inspection the test schedule (Table 4A and Table 4B) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of the sectional specification EN129200:1994. Notes to Table 4A and Table 4B Table

40、4A Lot-by-lot inspection (Group A and B) This table is to be used for defining characteristics which are additional to or tighter than those given in the sectional specification. (1) Clause numbers of tests and performance requirements refer to the sectional specification EN 129200:1994. (2) D =dest

41、ructive ND =non destructive P =periodicity (in months) n =number of specimens (sample size) c =number of permissible defectives (acceptance criterion) IL =inspection level (selected from IEC 410) AQL =acceptable quality level (selected from IEC 410) Sub-clause number and test (1) D or ND (2) Conditi

42、ons of test (1) IL AQL Performance requirements (1) (2) Group A1 ND S4 1,0 4.1 Visual examination No visible damage Marking legible, see 1.5 4.1 Dimensions (Detail) See Table 1 of this specification Group A2 ND II 0,25 4.2.1 Inductance Within specified tolerance 4.2.2 Q-factor See Table 2 of this sp

43、ecification Group A3 ND S3 1,0 See Table 2 of this specification 4.2.3 Self-resonant-frequency 4.2.4 D.C. resistance Notes see page 6EN129202:1994 BSI 01-2000 7 Table 4A Lot-by-lot inspection (Group A and B) Table 4B Periodic tests (Group C) Sub-clause number and test (1) D or ND (2) Conditions of t

44、est (1) IL AQL Performance requirements (1) (2) Group B1 D S3 1,0 4.5 Solderability Ageing (if required Duration: 4 h Temperature: 155 C) Method:. Good tinning as evidenced by free flowing of the solder with wetting of the terminations or solder shall flow within.s, as applicable 4.14.2 Solvent resi

45、stance of marking (if required) Solvent temperature: (23 5) C Method 1 Rubbing material: cotton wool Legible marking 4.4.3 Final measurement Visual examination As in 4.5.3 Notes see page 6 Sub-clause number and test (1) D or ND (2) Conditions of test (1) P n (2) c Performance requirements (1) Group

46、C1A D 12 9 1 4.3.1 Initial measurements Inductance Q-factor D.C. resistance 4.3 Robustness of terminations Visual examination No visible damage 4.4 Resistance to soldering heat Method:. . 4.13.1 Component solvent resistance (if required) Solvent:. Solvent temperature:. Method 2 Recovery:. No visible

47、 damage 4.4.2 Final measurements Visual examination No visible damage Inductance k 3% of value measured in4.3.1 Q-factor k 20% compared to values measured in 4.3.1 D.C. resistance k 3% of value measured in4.3.1 Notes see page 6EN129202:1994 8 BSI 01-2000 Table 4B Periodic tests (Group C) Sub-clause

48、number and test (1) D or ND (2) Conditions of test (1) P n (2) c Performance requirements (1) Group C1B D 12 18 1 4.6.1 Initial measurements Inductance Q-factor D.C. resistance 4.6 Rapid change of temperature T A= Lower category temperature T B= Upper category temperature Five cycles Duration t = 30

49、 min Visual examination No visible damage 4.7 Vibration For mounting method seedetail specification Frequency range: from.Hz toHz Amplitude: 0,75 mm or Acceleration: 98 m/s 2(whichever is the less severe) Total number of cycles: 15 4.7.2 Final inspection Visual examination No visible damage 4.8 Bump (or shock) (asrequired) For mounting method seedetail specification Number of bumps:. Acceleration:.m/s 2 Duration of pulse:.ms 4.9 Shock (or bump) (asrequi