BS EN 13126-10-2008 Building hardware - Requirements and test methods for windows and doors height windows - Arm-balancing systems《建筑五金 窗户和门上窗的要求和试验方法 臂平衡设备》.pdf

1、BS EN13126-10:2008ICS 91.190NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDBuilding hardware Requirements and testmethods for windowsand doors heightwindowsPart 10: Arm-balancing systemsLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Un

2、controlled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 March2009 BSI 2009ISBN 978 0 580 54620 4Amendments/corrigenda issued since publicationDate CommentsBS EN 13126-10:2008National forewordThis British Standard is the UK impl

3、ementation of EN 13126-10:2008. Itsupersedes DD CEN/TS 13126-10:2004 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/538/4, Building hardware.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publica

4、tion does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c

5、) BSIBS EN 13126-10:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13126-10November 2008ICS 91.190 Supersedes CEN/TS 13126-10:2004 English VersionBuilding hardware - Requirements and test methods for windowsand doors height windows - Part 10: Arm-balancing systemsQuincaillerie pour le btiment

6、 - Exigences et mthodesdessai des ferrures de fentres et portes-fentres - Partie10: Compas projectionBaubeschlge - Beschlge fr Fenster und Fenstertren -Anforderungen und Prfverfahren - Teil 10:SenkklappflgelsystemeThis European Standard was approved by CEN on 5 October 2008.CEN members are bound to

7、comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Manag

8、ement Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the

9、official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, S

10、lovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN n

11、ational Members.Ref. No. EN 13126-10:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 2 Contents Page Foreword3 1 Scope.5 2 Normative references 5 3 Terms and definitions5 4 Classification5 4.1 General5

12、4.2 Category of use (1 first digit) .5 4.3 Durability (2 second digit)5 4.4 Mass (3 third digit) 6 4.5 Fire resistance (4 fourth digit) .6 4.6 Safety in use (5 fifth digit) 6 4.7 Corrosion resistance (6 sixth digit).6 4.8 Security (7 seventh digit) .6 4.9 Application (8-eigth digit)6 4.10 Test sizes

13、 (9 ninth digit) .6 4.11 Example of classification for arm-balancing systems.7 5 Requirements .7 5.1 General7 5.2 Durability test .7 5.3 Static load test7 6 Test equipment.8 7 Test methods8 7.1 Samples 8 7.2 Durability test procedure.8 7.3 Static load test procedure.9 7.4 Corrosion resistance .9 Ann

14、ex A (informative) Test method diagrams10 Annex B (normative) Flow chart of test procedure12 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 3 Foreword This document (EN 13126-10:2008) has been prepared by Tec

15、hnical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, a

16、nd conflicting national standards shall be withdrawn at the latest by May 2009. This document supersedes CEN/TS 13126-10:2004. This European Standard is one of a series of European Standards dedicated to building hardware products. A full contribution to the preparation of this European Standard has

17、 been made by the European manufacturers organization “ARGE” and national standards bodies. EN 13126 Building hardware Requirements and test methods for windows and doors height windows consists of the following parts: Part 1: Requirements common to all types of hardware Part 2: Casement fastener ha

18、ndles1)Part 3: Manoeuvring fittings for espagnolette bolts/sliding button1)Part 4: Espagnolette bolts1)Part 5: Devices that restrict the opening of windows1)Part 6: Variable geometry stay hinges (with or without a friction system) Part 7: Finger catches Part 8: Tilt grade 10/2: for use only on proje

19、cting bottom-hung windows (type J); grade 10/3: for use on both projecting top-hung and bottom hung windows (type H and / or J). 4.10 Test sizes (9 ninth digit) The ninth digit shows the test sizes in accordance with 4.10 of EN 13126-1:2006 as follows: S.W.2)in mm / S.H.3)in mm. EXAMPLE 1 200 mm S.R

20、.W. 900 mm S.R.H.The specified size is a test size only. It does not relate to the maximum size to which a window may be fabricated. For instances where an arm-balancing system is available in a range of sizes to suit differing window sizes it shall be tested at the size which gives the most severe

21、impact on the hardware, as recommended by the hardware manufacturer. This size is then recorded as the ninth digit. 2)S.R.W. = sash rebate width 3)S.R.H. = sash rebate height Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 1312

22、6-10:2008 (E) 7 4.11 Example of classification for arm-balancing systems Table 1 Example of classification for Arm-balancing Systems 1 2 3 4 5 6 7 8 9 - 4 050 0 1 3 - 10/1 1 200/1 200 This denotes arm-balancing systems, which have: Digit 1 category of use - (no requirements); Digit 2 durability grad

23、e 4 (15 000 cycles); Digit 3 mass 50 kg; Digit 4 fire resistance grade 0 (no requirements); Digit 5 safety in use grade 1; Digit 6 corrosion resistance grade 3; Digit 7 security - (no requirements); Digit 8 applicable part tested in accordance with part 10 of this standard for a projecting top hung

24、window; Digit 9 test sizes S.R.W.1)= 1 200 mm, S.R.H.2)= 1 200 mm. 5 Requirements 5.1 General The requirements of arm-balancing systems shall be in accordance with Clause 5 of EN 13126-1:2006. 5.2 Durability test The test specified in 7.2 shall be used to ensure the hardware is capable of continued

25、operation after cycling in accordance with grades specified in 7.2, with regard given to normal maintenance. On completion of the durability test in accordance with 7.2. Arm-balancing system shall continue to function normally. 5.3 Static load test The test specified in 7.3 shall be used to ensure t

26、he mechanical strength of the hardware is appropriate for its intended use. On completion of the static load test in accordance with 7.3. Arm-balancing system shall continue to function normally. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN

27、 13126-10:2008EN 13126-10:2008 (E) 8 Maximum opening distance, measured between the free edge of the sash and the frame, shall not vary by more than 5 mm. 6 Test equipment The arm-balancing system shall be installed in the test specimen for testing as in Clause 6 of EN 13126-1:2006, and in accordanc

28、e with the manufacturers fixing instructions. NOTE The hardware manufacturer should provide test specimens for the testing institute. A drawing of the profile cross-section with relevant information should be enclosed in the test application, which also contains the necessary hardware installation i

29、nformation for the windows. The test shall be conducted on a test rig which corresponds in function and shape to the window for which the hardware was intended. The hardware tested shall conform to the manufacturers recommendation for size and mass of the test specimen. 7 Test methods 7.1 Samples Th

30、ree samples shall be tested in accordance with this European Standard. sample A performance tests; sample B corrosion test; sample C retained for reference control. NOTE 1 Sample B should only be necessary if no test report can be supplied by the manufacturer regarding the testing of the hardware co

31、mponent or set in accordance with EN 1670. NOTE 2 Sample C should be retained by the test institute for the duration of the validity of the test report. NOTE 3 All window fastening devices should not be engaged when measuring the clearance gap between sash and frame. 7.2 Durability test procedure An

32、y restrictor shall be disabled before any testing commences. Cycle the window in accordance with one of the following grades at the rate of 250250+cycles/h. grade 3: 10 000 cycles (+ 1 %) cycles; grade 4: 15 000 cycles (+ 1 %) cycles; grade 5: 25 000 cycles (+ 1 %) cycles. NOTE 1 Opening velocity is

33、 determined by the sash size and weight. Closing velocity should not exceed the opening velocity. Cycle the sash, in accordance with Clause 8 of EN 13126-1:2006, from the fully closed position to the fully open position. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncont

34、rolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 9 NOTE 2 All moving parts requiring lubrication may be lubricated unless the hardware is claimed to be maintenance free in accordance with hardware manufacturers instructions. Return the window to the closed position. The hardware shall con

35、form to the acceptance criteria of 8.4 of EN 13126-1:2006 and 5.2 of this European Standard. 7.3 Static load test procedure Measure and record the clearance gap between the sash and frame at the opening edge of the window. Measurements shall be taken at two points; at each corner of the sash no more

36、 than 50 mm from each side and along the opening edge (see Figure A.1). Open the sash to its maximum open position. Secure the sash in this position preventing further sash movement (see Figure A.2). Apply a force perpendicular to the sash of 500 N 250+N in increments of 100 N 250+N at the centre of

37、 the bottom of the sash. Maintain force of 500 N for 60 s 50+s. Return the window to the closed position. Measure and record the clearance gap between the sash and the frame at the opening edge of the window. Measurements shall be taken at the same position as used prior to the test commencing. The

38、hardware shall conform to the acceptance criteria of 8.4 of EN 13126-1:2006 and 5.3 of this European Standard. 7.4 Corrosion resistance NOTE 1 A test should only be necessary if no test report can be supplied by the manufacturer in accordance with EN 1670. All corrosion tests shall be on original ne

39、w samples. For Zinc galvanized surfaces on iron or steel the specified thickness of 12 (class 3) or 16 (class 4) is not necessary if other surface protection methods are used to conform to the requirements (minimum time to formation of white corrosion products) of ISO 4520: 1981. (= micrometre) Unle

40、ss a test report can be provided by the manufacturer the hardware shall be tested in accordance with EN 1670. NOTE 2 The evaluation of the corrosion resistance is limited to the essential areas (as a rule, the visible surfaces of the installed hardware). Exempt from the corrosion resistance evaluati

41、on are: rivet locations; locations of later processing (for example: cleaved surfaces that result from cropping the hardware components, millings); non surface-treated parts/surfaces, provided they are not in the visible vicinity of the hardware (for example: screw guide-holes made of zinc die-cast)

42、; welding joints and their immediate surroundings. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 10 Annex A (informative) Test method diagrams 1332334Key 1 width 3 specimen 2 height 4 measured clearance Figu

43、re A.1 Static load test - Elevation (showing typical window frame and casement used as apparatus) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 11 500 N500 NFigure A.2 Static load test - Load diagrams (showi

44、ng method of loading specimen via apparatus) Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008EN 13126-10:2008 (E) 12 Annex B (normative) Flow chart of test procedure 7.4CorrosionResistance7.2DurabilityTest7.3Static LoadTestRetain

45、forreferencecontrolSample CSample BStartFinishSample ALicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled Copy, (c) BSIBS EN 13126-10:2008This page has been intentionally left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/07/2009 07:38, Uncontrolled

46、 Copy, (c) BSIBS EN13126-10:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and

47、at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and servi

48、ces.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members

49、an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to ord