BS EN 13126-15-2008 Building hardware — nRequirements and test nmethods for windows nand doors height nwindows — nPart 15 Rollers for horizontal sliding nand sliding folding window.pdf

1、BRITISH STANDARDBS EN 13126-15:2008Building hardware Requirements and test methods for windows and doors height windows Part 15: Rollers for horizontal sliding and sliding folding windows and doorsICS 91.190g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g

2、49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 13126-15:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008ISBN 978 0 580 55688 3National forewordThis Br

3、itish Standard is the UK implementation of EN 13126-15:2008. It supersedes DD CEN/TS 13126-15:2004 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/4, Building hardware

4、.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from

5、 legal obligations. Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13126-15January 2008ICS 91.190 Supersedes CEN/TS 13126-15:2004 English VersionBuilding hardware - Requirements and test methods for windowsand doors height windows - Part

6、15: Rollers for horizontal slidingand sliding folding windows and doorsQuincaillerie pour le btiment - Exigences et mthodesdessai des ferrures de fentres et portes-fentres - Partie15 : Roulements pour portes-fentres et fentrescoulissantes lhorizontale et accordonBaubeschlge - Beschlge fr Fenster und

7、 Fenstertren -Anforderungen und Prfverfahren - Teil 15:Horizontalscheibe- und Faltscheibe-Fenster undFenstertrenThis European Standard was approved by CEN on 5 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ

8、eanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English,

9、French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus

10、, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EU

11、ROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13126-15:2008: EEN 13126-15:2008 (E) 2 Contents Page Foreword. 3 1 Scope

12、4 2 Normative references . 4 3 Terms and definitions. 4 4 Classification. 5 4.1 General. 5 4.2 Category of use (1 first digit) 5 4.3 Durability (2 second digit). 5 4.4 Mass (3 third digit) . 5 4.5 Fire resistance (4 fourth digit) 5 4.6 Safety in use (5 fifth digit) . 5 4.7 Corrosion resistance (6 si

13、xth digit) 5 4.8 Security (7 seventh digit) 6 4.9 Application (8 eighth digit) 6 4.10 Test Sizes (9 ninth digit) 6 4.11 Example of classification for rollers . 7 5 Requirements 7 5.1 General. 7 5.2 Test requirements . 7 5.2.1 Durability test for rollers for horizontal sliding windows and doors (wind

14、ow type N). 7 5.2.2 Durability test for the complete sliding folding hardware set (window type Q, R and S) . 8 5.2.3 Resistance to additional loading (window type Q, R and S) 10 5.2.4 Static endurance test at ambient temperature. 10 6 Test equipment 10 6.1 General. 10 6.2 Rollers for horizontal slid

15、ing windows and doors (window type N) 10 6.3 Hardware sets for sliding folding windows and doors (window types Q, R and S). 10 7 Test procedures 11 7.1 Samples . 11 7.2 Durability test 11 7.2.1 Durability test for rollers for horizontal sliding windows and doors (window type N). 11 7.2.2 Durability

16、test for hardware sets for sliding folding windows and doors (window types Q, R and S) 12 7.3 Additional loading test (window types Q, R and S). 13 7.3.1 Additional loading test in a 90 turn position of sash 3. 13 7.3.2 Additional loading test in the folded position14 7.4 Static endurance test at am

17、bient temperature. 14 7.4.1 Rollers for horizontal sliding windows and doors (window type N) 14 7.5 Corrosion resistance 15 Annex A (informative) Test assembly: rollers of window opening type N 16 Annex B (informative) Test assembly: rollers of window opening types Q, R and S. 17 Annex C (normative)

18、 Flow chart of test procedures 21 Bibliography . 22 BS EN 13126-15:2008EN 13126-15:2008 (E) 3 Foreword This document (EN 13126-15:2008) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. Thi

19、s European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2008, and conflicting national standards shall be withdrawn at the latest by July 2008. Attention is drawn to the possibility that some of the ele

20、ments of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 13126-15:2004. A full contribution to the preparation of this European Standard has been made by the European ma

21、nufacturers organisation ARGE and National Standards institutions. This European Standard is one of a series of European Standards dedicated to building hardware products. It is divided into seventeen parts to incorporate all types of windows and door height windows. Informative Annex A of EN 13126-

22、1:2006 provides detailed schedules of the elements of components of the seventeen parts of this European Standard. Informative Annex A of EN 13126-1:2006 depicts the “list of parts and titles and their reference to the relevant window types” of the seventeen parts of this European Standard. Normativ

23、e and informative annexes to all parts of this European Standard are indicated in the content of the several parts The performance tests incorporated in this standard are considered to be reproducible and as such will provide a consistent and objective assessment of the performance of these products

24、 throughout CEN Member States. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hun

25、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13126-15:2008EN 13126-15:2008 (E) 4 1 Scope This part of EN 13126 provides requirements and test methods f

26、or the durability, strength, security and function of rollers for horizontal sliding and inward or outward sliding folding windows and door height windows in accordance with common applications as shown in Annex B, EN 13126-1:2006. This standard is applicable to rollers, irrespective of whether they

27、 are adjustable or not, and irrespective of the method or type of fixing or if they are used independently, or in multiples or combinations. NOTE 1 Guide tracks, laterals guides and rails used while testing the rollers for sliding folding windows and door height windows (window types N Q, R and S) a

28、re considered to be part of the complete sliding folding hardware set. NOTE 2 The hinges used while testing the rollers for sliding folding windows and door height windows (window types Q, R and S) are considered to be part of the complete sliding folding hardware set. Testing the hinges separately

29、is not required in this case. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

30、es. EN 1670, Building hardware Corrosion resistance Requirements and test methods EN 12519:2004, Windows and pedestrian doors Terminology EN 13126-1:2006, Building hardware Requirements and test methods for windows and doors height windows Part 1: Requirements common to all types of hardware ISO 452

31、0, Chromate conversion coatings on electroplated zinc and cadmium coating 3 Terms and definitions For the purposes of this European Standard the definitions given in EN 13126-1:2006 and EN 12519:2004 and the following apply. NOTE The following terms and definitions apply to horizontal sliding and sl

32、iding folding windows and door height windows made of timber, PVC, aluminium or steel and their appropriate material combinations. 3.1 roller assembly of one or more rolls in a single, or multiple, casing, which supports horizontal sliding windows, or sliding folding windows and door height windows.

33、 These may be aligned in a straight line or rotate about an axis for sliding folding windows and door height windows. Otherwise known as a bogey 3.2 roll singular wheel in a roller BS EN 13126-15:2008EN 13126-15:2008 (E) 5 3.3 lateral guide hardware component, which guides the lateral movement of ho

34、rizontal sliding and sliding folding windows and door height windows 3.4 guide track track fixed on the top (top guide track) or bottom (bottom guide track) in which a guide runs 3.5 rail rail fixed on the top (top rail) or bottom (bottom rail) on which rollers run 4 Classification 4.1 General The c

35、lassification for rollers shall be in accordance with the requirements of clause 4 of EN 13126-1:2006. 4.2 Category of use (1 first digit) No marking is required for the category of use in accordance with 4.2 of EN 13126-1:2006. 4.3 Durability (2 second digit) Grades shall be in accordance with 4.3

36、of EN 13126-1:2006. 4.4 Mass (3 third digit) Grades shall be in accordance with 4.4 of EN 13126-1:2006. NOTE Rollers for use in horizontal sliding windows and doors (window type N) should be tested with half of the maximum sash mass, as long as the hardware manufacturer specifies a minimum of two ro

37、llers per sash. For example if the roller is specified by the hardware manufacturer for a maximum sash mass of 40 kg, the roller should be tested with 40 kg / 2 = 20 kg in accordance with 7.2.1. 4.5 Fire resistance (4 fourth digit) One grade shall be identified in accordance with 4.5 of EN 13126-1:2

38、006. grade 0 : no requirements. 4.6 Safety in use (5 fifth digit) One grade is identified in accordance with 4.6 of EN 13126-1:2006. grade 1: The hardware shall conform to the requirements of part 1 and part 15 of this standard. 4.7 Corrosion resistance (6 sixth digit) Grades shall be in accordance

39、with 4.7 of EN 13126-1:2006. BS EN 13126-15:2008EN 13126-15:2008 (E) 6 4.8 Security (7 seventh digit) No marking is required for the category of security in accordance with 4.8 of EN 13126-1:2006. 4.9 Application (8 eighth digit) The eighth digit shows “15/1”, “15/2” or “15/3” indicating the part of

40、 the standard that was used for testing the rollers and their common application for horizontal sliding windows or sliding folding windows and door height windows in accordance with 4.9 of EN 13126-1:2006. Three grades are identified as follows: grade 15/1: for use on horizontal sliding windows and

41、door height windows (type N); grade 15/2: for use on centre pivot sliding folding windows and door height windows (type Q); grade 15/3: for use on outward or inward corner pivot sliding folding windows and door height windows (type R and/or S). 4.10 Test Sizes (9 ninth digit) The ninth digit shows t

42、he test sizes in accordance with 4.10 of EN 13126-1:2006. for example as follows: S.R.W.1)in mm / S.R.H.2)in mm tolerance 5 mm. no test size is required for this category (15/1 for window type N) 900 mmS.R.W1)x 1 900 mmS.R.H2)(15/2 and 15/3 for window types Q, R and S) The specified sizes are test s

43、izes only. They do not relate to the maximum or minimum sizes to which a window may be fabricated. NOTE 1 The manufacturers product-documentation should advise that in daily use windows, smaller or larger than those tested, should not be subjected to stronger forces than those for the specified test

44、 size. In the case of not being capable of manufacturing the specified test size due to the fact that the hardware field of application is smaller than these specified test sizes, smaller test sizes shall be used. In this case the window shall be tested in accordance with the largest possible S.R.W.

45、1) (or S.R.H.2) as specified by the hardware manufacturers appropriate documentation and a S.R.H.2)(or S.R.W.1) in a ratio of 1 900/900 (factor 2,111). NOTE 2 This means that if the specified test sizes are larger than those which can be manufactured, the test specimens shall be tested using the lar

46、gest possible S.R.W1) or S.R.H2in accordance with the manufacturers documentation and using a S.R.H2to S.R.W1) ratio of 1 900/900 (factor 2,111) Example 1 largest possible S.R.W.1)= 700 mm = S.R.W.1)of the test specimen 700 mm X 1 900/900 = 1 478 mm S.R.H.2)= 1 478 mm = S.R.H.2)of the test specimen

47、Example 2 largest possible S.R.H.1)= 1 600 mm = S.R.H.1)of the test specimen 1 600 mm X 900/1 900 = 758 mm S.R.W.2)= 758 mm = S.R.W.2)of the test specimen NOTE 3 The missing dimensions in each case (S.R.H1)or S.R.W2) should be calculated in accordance with example 1 or 2 with the objective of establ

48、ishing the maximum test-format, which lies within the hardware manufacturers application range. 1)S.R.W. = sash rebate width 2)S.R.H. = sash rebate height BS EN 13126-15:2008EN 13126-15:2008 (E) 7 4.11 Example of classification for rollers Table 1 Example of classification for rollers 1 2 3 4 5 6 7

49、8 9 - 4 080 0 1 2 - 15/2 900/1900 This denotes rollers for horizontal sliding windows or sliding folding windows and doors, which have: Digit 1 category of use - (no requirements) Digit 2 durability grade 4 (15 000 cycles) Digit 3 mass 80 kg Digit 4 fire resistance grade 0 (no requirements) Digit 5 safety in use grade 1 Digit 6 corrosion resistance grade 2 Digit 7 security - (no requirements) Digit 8 applicable part grade 15/2; tested according to part 15 of this standa