BS EN 13179-2-2000 Test for filler aggregate used in bituminous mixtures - Bitumen number《沥青混合料用填充集料试验 沥青值》.pdf

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 13179-2:2000 The Eu

2、ropean Standard EN 13179-2:2000 has the status of a British Standard ICS 75.140; 91.100.15 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Tests for filler aggregate used in bituminous mixtures Part 2: Bitumen numberThis British Standard, having been prepared under the directi

3、on of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 October 2000 BSI 10-2000 ISBN 0 580 36026 1 BS EN 13179-2:2000 Amendments issued since publication Amd. No. Date Comments National foreword This Bri

4、tish Standard is the official English language version of EN 13179-2:2000, which is included in a package of new European Standards being prepared by CEN/TC 154 relating to aggregates. Although the English language versions of these European Standards will be adopted as British Standards as they bec

5、ome available, the existing British Standards for aggregates will be retained, but only until such time that the completed package of European Standards become available. The original group of British Standards will then be withdrawn and this will be noted in Update Standards The UK participation in

6、 its preparation was entrusted by Technical Committee B/502, Aggregates, to Subcommittee B/502/6, Test methods, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep

7、the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European pub

8、lications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary pr

9、ovisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to

10、 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13179-2 August 2000 ICS 75.140 English version Tests for filler aggregate used in bituminous mixtures - Part 2: Bitumen number Ess

11、ais sur les fillers utiliss dans les mlanges bitumineux - Partie 2: Viscosit apparente (Nombre-bitume) Prfverfahren fr mineralische Fller in bitumenhaltigen Mischungen - Teil 2: Bitumenzahl This European Standard was approved by CEN on 13 July 2000. CEN members are bound to comply with the CEN/CENEL

12、EC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CE

13、N member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN m

14、embers are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS

15、ATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13179-2:2000 EPage 2 EN 13179-2:2000 BSI 10-2000 Contents Page Foreword 3 1 Scope 4

16、2 Normative references 4 3 Terms and definitions 4 4 Principle 4 5 Apparatus 5 6 Preparation of test portions 5 7 Procedure 5 8 Calculation and expression of results 6 9 Test report 6 Annex A (informative) Precision 7Page 3 EN 13179-2:2000 BSI 10-2000 Foreword This European Standard has been prepare

17、d by Technical Committee CEN/TC 154, Aggregates, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2001, and conflicting national standards shall be

18、 withdrawn at the latest by December 2003. This European Standard forms part of series of tests for bituminous bound filler aggregates. Test methods for other properties of aggregates will be covered by parts of the following European Standards: EN 932 Tests for general properties of aggregates; EN

19、933 Tests for geometrical properties of aggregates; EN 1097 Tests for mechanical and physical properties of aggregates; EN 1367 Tests for thermal and weathering properties of aggregates; EN 1744 Tests for chemical properties of aggregates. The other part of EN 13179 will be: Part 1: Delta ring and b

20、all test. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, N

21、orway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 4 EN 13179-2:2000 BSI 10-2000 1 Scope This European Standard specifies the procedure for determining the apparent viscosity of a water-filler aggregate mixture, expressed numerically. The test procedure is applicable to filler a

22、ggregate used in bituminous mixtures to regulate production control.2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed

23、 hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 932-

24、2, Tests for general properties of aggregates - Part 2: Methods for reducing laboratory samples EN 932-5, Tests for general properties of aggregate - Part 5: Common equipment and calibration EN 1426, Bitumen and bituminous binders - Determination of needle penetration 3 Terms and definitions For the

25、 purposes of this European Standard the following terms and definitions apply: 3.1 bitumen number amount of water, when mixed with 100 g of filler aggregate, to give a mixture with a defined apparent viscosity 3.2 laboratory sample reduced sample derived from a bulk sample for laboratory testing 3.3

26、 test portion sample used as a whole in a single test 4 Principle A filler aggregate mixture placed in a cylindrical cup is penetrated for 5 s with an aluminium stamp 8 mm in diameter with a mass of 15 g. The amount of water required to give a penetration of the stamp in the mixture between 5,0 mm a

27、nd 7,0 mm is determined.Page 5 EN 13179-2:2000 BSI 10-2000 5 Apparatus 5.1 All apparatus, unless otherwise stated, shall conform to the general requirements of EN 932-5. 5.2 Balance, accurate to 0,1 g. 5.3 Stainless steel dish, shaped like a truncated cone, height (65 5) mm, upper edge (95 5) mm in

28、diameter, with a flat bottom (65 5) mm in diameter. 5.4 50 ml burette. 5.5 Flexible spatula. 5.6 Cylindrical cup, inner diameter (30 1) mm, height (30 1) mm with a wall thickness of (2,0 0,2) mm. 5.7 Penetrometer, complying with EN 1426. 5.8 Round aluminium stamp, (8,0 0,1) mm in diameter, mass (15,

29、0 0,2) g, fitting into the penetrometer in place of the needle holder. 5.9 Timer, accurate to 0,1 s. 5.10 Demineralized water. 6 Preparation of test portions Reduce the undried laboratory sample to test portions in accordance with EN 932-2. At least three test portions with a mass of at least 50 g a

30、re required. NOTE A mechanical sampler can be used. 7 Procedure Weigh (50,0 0,1) g of undried filler in the stainless steel dish and add x 1 ml of demineralized water from the burette. Mix and stir for (300 10) s with the spatula. NOTE 1 x 1is the expected amount of water required to give a valid va

31、lue of penetration of the stamp into the mixture. NOTE 2 Care should be taken to spread the mixture as little as possible to prevent the water from evaporating. Fill the cylindrical cup with the mixture, ensuring that no air bubbles are entrapped and smooth the surface. Place the cup with the mixtur

32、e on the base of the penetrometer. Level the bottom of the stamp with the surface of the mixture, reset the dial to zero and allow the stamp to penetrate into the mixture for (5,0 0,1) s. Measure the penetration to the nearest 0,1 mm and the amount of water from the burette (x 1ml) to the nearest 0,

33、1 ml. If the penetration is smaller than 5,0 mm or greater than 7,0 mm, mix a further test portion with an adjusted volume of water (x 2ml) and repeat the procedure specified in this clause.Page 6 EN 13179-2:2000 BSI 10-2000 8 Calculation and expression of results Calculate the bitumen number BN in

34、accordance with the following equation: BN = 2x n where x n is the numerical value of the volume of water, in millilitres, used to give a test result with a penetration between 5, 0 mm and 7,0 mm. Express the calculated value to the nearest whole number. NOTE An indication of precision is given in a

35、nnex A. 9 Test report 9.1 Required data The test report shall include the following information: a) the apparent viscosity (bitumen number); b) reference to this European Standard; c) the name or the brand of the filler aggregate; d) the date of the test. 9.2 Optional data The test report can includ

36、e the following information: a) name and location of sample source; b) a description of the material; c) a description of the sampling procedure.Page 7 EN 13179-2:2000 BSI 10-2000 Annex A ( informative) Precision Estimates of the repeatability (r) and the reproducibility (R) are as follows: r = 2; R

37、 = 3.BS EN 13179-2:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

38、 | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendm

39、ent or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard wou

40、ld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions

41、 of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that ha

42、ve been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are als

43、o available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of the

44、se and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, De

45、signs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard

46、, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.