BS EN 13282-3-2015 Hydraulic road binders Conformity evaluation《液体公路粘合剂 合格评价》.pdf

1、BSI Standards PublicationBS EN 13282-3:2015Hydraulic road bindersPart 3: Conformity evaluationBS EN 13282-3:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13282-3:2015. It supersedes BS EN 13282-3:2013 which is withdrawn.The UK participation in its prepara

2、tion was entrusted to Technical Committee B/516/14, Special hydraulic road binders.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its

3、correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 86478 0 ICS 93.080.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and

4、 Strategy Committee on 30 April 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13282-3 April 2015 ICS 93.080.20 Supersedes EN 13282-3:2013English Version Hydraulic road binders - Part 3: Conformity evaluation Liants

5、 hydrauliques routiers - Partie 3: valuation de la conformit Hydraulische Tragschichtbinder - Teil 3: Konformittsbewertung This European Standard was approved by CEN on 1 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givin

6、g this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offic

7、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of

8、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

9、weden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for

10、 CEN national Members. Ref. No. EN 13282-3:2015 EBS EN 13282-3:2015EN 13282-3:2015 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Factory production control by the manufacturer . 6 4.1 General requirements 6 4.1.1 Concept . 6 4.1.2 Works quality manua

11、l . 6 4.1.3 Management systems . 7 4.1.4 System of documentation . 7 4.2 Internal quality control 7 4.2.1 Process control 7 4.2.2 Measuring and testing . 8 4.2.3 Handling, storage, packaging and delivery 8 4.3 Autocontrol testing of samples 8 4.3.1 Sampling and testing 8 4.3.2 Evaluation of results

12、of autocontrol testing of samples . 8 4.3.3 Corrective action 9 4.3.4 Measuring and test equipment for autocontrol testing . 9 4.3.5 Quality records . 9 5 Determination of the product-type . 9 6 Assessment of the factory production control . 10 6.1 Continuous surveillance, assessment and evaluation

13、of factory production control . 10 6.1.1 Inspection tasks . 10 6.1.2 Frequency of inspections . 10 6.1.3 Reports . 10 6.2 Initial inspection of the factory and the factory production control 10 6.2.1 Inspection of a new factory 10 6.2.2 Inspection of an existing factory 10 6.2.3 Criteria for the ass

14、essment of the production equipment 10 6.2.4 Criteria for the activities of the laboratories . 11 6.2.5 Reports . 11 7 Actions in the event of non-conformity . 11 7.1 Actions to be taken by the manufacturer 11 7.2 Actions to be taken in case of a non-conforming factory production control system 11 8

15、 Requirement for dispatching centres 12 8.1 General 12 8.2 Tasks for the intermediary 12 8.2.1 Quality control 12 8.2.2 Confirmation autocontrol testing of samples taken at the dispatching centre 12 Bibliography 14 BS EN 13282-3:2015EN 13282-3:2015 (E) 3 Foreword This document (EN 13282-3:2015) has

16、been prepared by Technical Committee CEN/TC 51 “Cement and building limes”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2015 and conflicting na

17、tional standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document super

18、sedes EN 13282-3:2013. This European Standard, EN 13282, Hydraulic road binders consists of the following parts: Part 1: Rapid hardening hydraulic road binders Composition, specifications and conformity criteria Part 2: Normal hardening hydraulic road binders Composition, specifications and conformi

19、ty criteria Part 3: Conformity evaluation Compared to the version EN 13282-3:2013 the following major changes have been included in this document: Use of the terminology given by the Construction Products Regulation (Regulation (EU) No 305/2011). Link between this European Standard and Annexes ZA of

20、 European Standards covering cements. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugos

21、lav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13282-3:2015EN 13282-3:2015 (E) 4 1 Scope T

22、his European Standard specifies the scheme for the assessment and verification of constancy of performance of hydraulic road binders and their conformity with the corresponding product specification standards EN 13282-1 and EN 13282-2. This European Standard provides technical rules for factory prod

23、uction control by the manufacturer, including autocontrol testing of samples. It also provides rules for actions to be followed in the event of non-conformity. This European Standard should be linked with Annexes ZA of European Standards covering hydraulic road binders, i.e. EN 13282-1 and EN 13282-

24、2, in particular for the assignments of tasks to the manufacturer and to the production control certification body. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only t

25、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement - Part 1: Determination of strength EN 196-2, Methods of testing cement - Part 2: Chemical analysis of cement EN 196-3, Methods of t

26、esting cement - Part 3: Determination of setting times and soundness EN 196-7, Methods of testing cement - Part 7: Methods of taking and preparing samples of cement EN 13282-1, Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criter

27、ia EN 13282-2, Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 AVCP abbreviation for assessment and verification of

28、 constancy of performance 3.2 certificate of conformity of factory production control document issued under the rules of this scheme for the AVCP indicating that adequate confidence is provided that factory production control is in conformity with the relevant product specification standard 3.3 conf

29、ormity mark protected mark applied on the basis of the certificate of conformity of the factory production control 3.4 initial period immediate period starting after the first issuing of the certificate of conformity of factory production control for a hydraulic road binder and at the latest from th

30、e first dispatching of hydraulic road binder BS EN 13282-3:2015EN 13282-3:2015 (E) 5 3.5 production control certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out the certification of the factory production control acc

31、ording to given rules of procedure and management 3.6 factory production control documented, permanent and internal control of production in a factory, in accordance with the relevant harmonised technical specifications 3.7 factory facility used by a manufacturer for the production of hydraulic road

32、 binders,using equipment which is suitable for continuous mass production of hydraulic road binder including, in particular, equipment for adequate grinding and homogenisation and the necessary silo capacity for the storage and dispatch of each hydraulic road binder produced Note 1 to entry: This eq

33、uipment and the production control applied allow the control of production to ensure that the requirements of the relevant product specification standard are met. 3.8 new factory factory which is not already producing hydraulic road binder(s) certified using this European Standard 3.9 existing facto

34、ry factory which is already producing hydraulic road binder(s) certified using this European Standard 3.10 depot bulk hydraulic road binder handling facility (not located at the factory) used for the dispatch of hydraulic road binder (whether in bulk or bagged) after transfer or storage where the ma

35、nufacturer has full responsibility for all aspects of the quality of the hydraulic road binder 3.11 dispatching centre facility (not located at the factory) for handling and dispatching of hydraulic road binder (received in bulk or in any other condition) by activities that shall not modify the char

36、acteristics or the integrity of the product received from the manufacturer, where an intermediary has full responsibility for all aspects of the quality of the hydraulic road binder 3.12 intermediary natural or legal person who takes from the manufacturer or the importer hydraulic road binder certif

37、ied using this European Standard and bearing the conformity mark, taking full responsibility for maintaining in a hydraulic road binder handling facility all aspects of the quality of the hydraulic road binder and who supplies the hydraulic road binder onwards to a further person 3.13 determination

38、of the product-type determination of the set of representative performance levels or classes of a construction product, in relation to its essential characteristics, on the basis of type testing (including sampling), type calculation, tabulated values or descriptive documentation of the product 3.14

39、 confirmation autocontrol testing continual testing carried out by an intermediary which consists of testing of samples taken by the intermediary at the point(s) of release from the dispatching centre BS EN 13282-3:2015EN 13282-3:2015 (E) 6 3.15 works quality manual document that provides informatio

40、n on the factory production control which is applied by a manufacturer at a particular factory to ensure conformity of the hydraulic road binder with the requirements of this European Standard and the relevant product specification standard 4 Factory production control by the manufacturer 4.1 Genera

41、l requirements 4.1.1 Concept Factory production control is exercised by the manufacturer and consists of internal quality control (see 4.2) complemented by testing of samples taken at manufacturing plant in accordance with a prescribed test plan1)(see 4.3) and an assessment of the performance of the

42、 hydraulic road binder on the basis of testing (including sampling) or descriptive documentation of this product . NOTE The requirements of this European Standard as regards factory production control take account of those clauses of EN ISO 9001 3 which are relevant to the production, process contro

43、l and testing of hydraulic road binder. 4.1.2 Works quality manual The manufacturers documentation and procedures for factory production control shall be described in a Works quality manual, which shall adequately describe, among other things: a) the quality aims and the organisational structure, re

44、sponsibilities and powers of the management with regard to product quality and the means to monitor the achievement of the required product quality and the effective operation of the internal quality control (see 4.1.3); b) the manufacturing and quality control techniques, processes and systematic a

45、ctions that will be used (see 4.2.1, 4.2.3 and 4.3.2); c) the inspections and tests that will be carried out before, during and after manufacture, and the frequency with which they will be carried out (see 4.2.2, 4.3.1 and 4.3.3). The Works quality manual prepared by the manufacturer for each factor

46、y shall include an adequate system of documentation (see 4.1.4 and 4.3.4). The Works quality manual shall address and document the procedures operated to ensure that the manufactured hydraulic road binder conforms to the technical specifications. The manual may reference associated documents which p

47、rovide further details of the autocontrol testing of samples and the internal quality control. For the purpose of this scheme, the term Works quality manual shall be considered to include these associated documents. In the case of an existing quality management system according to EN ISO 9001 3, it

48、may be examined if the corresponding quality manual meets all the requirements of this European Standard which are relevant to the factory production control of hydraulic road binder. Provided all the requirements are included, this quality manual may also be applied for certification of conformity

49、of the factory production control. 1)This testing corresponds to the autocontrol testing of samples of clause 4.3. BS EN 13282-3:2015EN 13282-3:2015 (E) 7 4.1.3 Management systems 4.1.3.1 Quality policy statement The Works quality manual shall include a statement by management defining its quality policy, objectives and commitments to the attainment of product quality. 4.1.3.2 Management representative The manufacturer shall appoint a management representative who, irrespective of other responsibilities, shall have defined and adequate authority and res