BS EN 13285-2010 Unbound mixtures Specifications《松散混合料 规范》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13285:2010Unbound mixtures SpecificationsBS EN 13285:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13285:2010. Itsupersedes BS

2、EN 13285:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/510/4, Cementitious bound materials, unboundgranular materials, waste materials and marginal materials.A list of organizations represented on this committee can beobtained on request to its

3、 secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 69989 4ICS 93.080.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was pu

4、blished under the authority of theStandards Policy and Strategy Committee on 31 October 2010.Amendments issued since publicationDate Text affectedBS EN 13285:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13285 September 2010 ICS 93.080.20 Supersedes EN 13285:2003English Version Unbound mi

5、xtures - Specifications Graves non traites - Spcifications Ungebundene Gemische - Anforderungen This European Standard was approved by CEN on 29 July 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s

6、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German)

7、. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, C

8、zech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT E

9、UROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13285:2010: EBS EN 13285:2010EN 13285:2010 (E) 2 Contents Page Forewor

10、d 41 Scope 52 Normative references 53 Terms and definitions .54 Requirements .64.1 General requirements 64.2 Aggregate requirements .64.3 Mixture requirements 74.3.1 Mixture designation .74.3.2 Fines content 74.3.3 Oversize 84.4 Grading requirements .84.4.1 General grading curve .84.4.2 Grading of i

11、ndividual batches . 114.5 Other requirements. 115 Evaluation of conformity 125.1 Sampling 125.2 Factory production control 125.3 Declaration of laboratory dry density and optimal water content . 125.4 Declaration of water soluble sulphate content 126 Designation and description . 127 Marking and lab

12、elling . 13Annex A (informative) Use of the supplier declared value 14A.1 Terminology 14A.2 Overall grading range . 14A.3 Supplier declared value grading range 15A.4 Supplier declared value . 15A.5 Tolerances for comparison with the supplier declared value 15Annex B (informative) Guidance on the ass

13、essment of the mechanical behaviour of unbound mixtures . 16Annex C (normative) Factory production control 17C.1 Introduction . 17C.2 Organization 17C.2.1 Responsibility and authority . 17C.2.2 Management representative for factory production control 17C.2.3 Management review 17C.3 Control procedure

14、s. 17C.3.1 Document and data control . 17C.3.2 Sub-contract services 18C.3.3 Knowledge of mixture components 18C.4 Management of the production . 18C.5 Inspection and test . 18C.5.1 General . 18C.5.2 Equipment . 18C.5.3 Frequency and location of inspections, sampling and tests . 19C.6 Records 20C.7

15、Control of non-conforming product 20BS EN 13285:2010EN 13285:2010 (E) 3 C.8 Handling, storage and conditioning in production areas . 20C.9 Transport and packaging 21C.9.1 Transport 21C.9.2 Packaging . 21C.10 Training of personnel 21Bibliography 22BS EN 13285:2010EN 13285:2010 (E) 4 Foreword This doc

16、ument (EN 13285:2010) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and

17、 conflicting national standards shall be withdrawn at the latest by March 2011. This document supersedes EN 13285:2003. The main change compared to the previous edition is that the former informative annex classifying mixtures containing recycled aggregates has been replaced by the general reference

18、 to EN 13242. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standard

19、s organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola

20、nd, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13285:2010EN 13285:2010 (E) 5 1 Scope This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. The requi

21、rements are defined with appropriate cross-reference to EN 13242. This European Standard applies to unbound mixtures of natural, artificial and recycled aggregates with a upper sieve size (D) from 8 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery. NOTE 1 Mixtures with an upper siev

22、e size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use. NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the l

23、ayer and are outside the scope of this European Standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inc

24、luding any amendments) applies. EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method EN 1744-1, Tests for chemical properties of aggregates Part 1: Chemical analysis EN 13242, Aggregates for unbound and hydraulically bound materi

25、als for use in civil engineering work and road construction EN 13286-1, Unbound and hydraulically bound mixtures Part 1: Test methods for laboratory reference density and water content Introduction, general requirements and sampling EN 13286-2, Unbound and hydraulically bound mixtures Part 2: Test m

26、ethods for the determination of the laboratory reference density and water content Proctor compaction EN 13286-3, Unbound and hydraulically bound mixtures Part 3: Test methods for laboratory reference density and water content Vibrocompression with controlled parameters EN 13286-4, Unbound and hydra

27、ulically bound mixtures Part 4: Test methods for laboratory reference density and water content Vibrating hammer EN 13286-5, Unbound and hydraulically bound mixtures Part 5: Test methods for laboratory reference density and water content Vibrating table 3 Terms and definitions For the purposes of th

28、is document, the following terms and definitions apply. NOTE Other useful terms and definitions are given in EN 13242. 3.1 unbound mixture granular material, normally of a controlled grading with d = 0, which is generally used in pavement bases and sub-bases BS EN 13285:2010EN 13285:2010 (E) 6 NOTE

29、An unbound mixture does not contain an added binder. 3.2 category level of a property expressed as a range of values or a limiting value NOTE There is no relationship between the categories of different properties. 3.3 grading particle size distribution expressed as the percentage by mass passing a

30、specified number of sieves 3.4 batch production quantity, delivery quantity, partial delivery quantity (railway wagon-load, lorry-load, ships cargo) or stockpile produced at one specific time under conditions that are presumed to be uniform NOTE With a continuous process the quantity produced during

31、 an agreed period is treated as a batch. 4 Requirements 4.1 General requirements The need for testing for all properties in this clause shall be limited according to the particular application or end use or origin of the mixture. When required, the tests specified in 4.2 to 4.5 shall be carried out

32、to determine appropriate properties. NOTE When a test is not required, it should be specified as a “No requirement”. 4.2 Aggregate requirements When required, the following properties of the aggregates used in the mixture shall be in accordance with EN 13242: shape of coarse aggregate; percentage of

33、 crushed or broken particles and of totally rounded particles in coarse aggregates; fines quality; resistance to fragmentation of coarse aggregate; particle density; water absorption; resistance to wear of coarse aggregate; chemical requirements; durability requirements. BS EN 13285:2010EN 13285:201

34、0 (E) 7 4.3 Mixture requirements 4.3.1 Mixture designation Mixtures shall be selected from Table 1. Table 1 Mixture designation 0/8 0/10 0/11,2 0/12,5 0/14 0/16 0/20 0/22,4 0/31,5 0/40 0/45 0/56 0/63 0/80 0/90 4.3.2 Fines content When required, the percentage of particles which pass the 0,063 mm sie

35、ve (fines) determined in accordance with EN 933-1 shall not exceed the values in Table 2, according to the category chosen. Table 2 Maximum fines content Percentage passing 0,063 mm sieve by mass Category 3 UF3 5 UF5 7 UF7 9 UF9 12 UF12 15 UF15No requirement UFNWhen required, the percentage of parti

36、cles passing the 0,063 mm sieve shall also be greater than the values given in Table 3, according to the category chosen. Table 3 Minimum fines content Percentage passing 0,063 mm sieve by mass Category 2 LF2 4 LF4 8 LF8No requirement LFNThe categories in Table 2 and Table 3 shall be chosen so that

37、the difference between the maximum fines content and the minimum fines content is not less than 3 %. BS EN 13285:2010EN 13285:2010 (E) 8 4.3.3 Oversize When determined in accordance with EN 933-1, the percentage of particles passing the upper (D) sieve shall lie within the ranges given in Table 4 ac

38、cording to the category chosen. Table 4 Oversize Percentage passing by mass Category 2 Da b1,4 DbDc 100 90 to 99 OC90 100 85 to 99 OC85 100 d80 to 99 OC80 100e75 to 99 OC75 aFor aggregate sizes where D is greater than 63 mm, only the oversize requirements related to the 1,4 D sieve apply because the

39、re is no ISO 565/R20 series sieve size larger than 125 mm. bWhere the sieves calculated as 1,4 D and 2 D are not exact sieve numbers in the ISO 565/R20 series then the next nearest sieve size shall be adopted. When D = 90 mm the 125 mm sieve shall be used as oversize. cThe percentage passing sieve s

40、ize D may be greater than 99 % but in such cases the supplier shall declare the typical grading. d For aggregate sizes where D is smaller than 63 mm, add a range of 90 to 100 to the 1,4 D sieve. e For aggregate sizes where D is smaller than 63 mm, add a range of 85 to 100 to the 1,4 D sieve. 4.4 Gra

41、ding requirements 4.4.1 General grading curve When required, the percentage by mass passing sieve A, sieve B, sieve C, sieve E and where specified in Table 6 sieve F and sieve G determined in accordance with EN 933-1 using the sieves defined in Table 5 shall be within the overall grading range appro

42、priate to the category selected from Table 6. BS EN 13285:2010EN 13285:2010 (E) 9 Table 5 Sieves for grading Mixture designation Sieve A Sieve B Sieve C Sieve E Sieve F Sieve G0/8 4 2 1 0,5 0/10 4 2 1 0,5 0/11,2 5,6 4 2 1 0,5 0/12,5 6,3 4 2 1 0,5 0/14 8 4 2 1 0,5 0/16 8 4 2 1 0,5 0/20 10 4 2 1 0,5 0

43、/22,4 11,2 5,6 2 1 0,5 0/31,5 16 8 4 2 1 0,5 0/40 20 10 4 2 1 0,5 0/45 22,4 11,2 5,6 2 1 0,5 0/56 31,5 16 8 4 2 1 0/63 31,5 16 8 4 2 1 0/80 40 20 10 4 2 1 0/90 45 22,4 11,2 5,6 2 1 NOTE Table 5 does not define sieve C and sieve G for all mixtures. In addition, for categories GA, GB, GC, GOand GPthe

44、mean value calculated from all gradings shall be within the supplier declared value grading range appropriate to the category selected from Table 6. BS EN 13285:2010EN 13285:2010 (E) 10 Table 6 Overall grading Grading range Percentage passing by mass CategorySieve A Sieve B Sieve C Sieve E Sieve F S

45、ieve G G Normal graded mixtures Overall 55 to 85 35 to 65 22 to 50 15 to 40 10 to 35 0 to 20 GASupplier declared value (S) 63 to 77 43 to 57 30 to 42 22 to 33 15 to 30 5 to 15 Overall 55 to 85 35 to 68 22 to 60 16 to 47 9 to 40 5 to 35 GBSupplier declared value (S) 63 to 77 43 to 60 30 to 52 23 to 4

46、0 14 to 35 10 to 30 Overall 50 to 90 30 to 75 20 to 60 13 to 45 8 to 35 5 to 25 GCSupplier declared value (S) 61 to 79 41 to 64 31 to 49 22 to 36 13 to 30 10 to 20 Open graded mixtures Overall 50 to 78 31 to 60 18 to 46 10 to 35 6 to 26 0 to 20 GOSupplier declared value (S) 58 to 70 39 to 51 26 to 3

47、8 17 to 28 11 to 21 5 to 15 Overall 43 to 81 23 to 66 12 to 53 6 to 42 3 to 32 No req. GPSupplier declared value (S) 54 to 72 33 to 52 21 to 38 14 to 27 9 to 20 Other mixtures Overall 50 to 90 30 to 75 15 to 60 no req. 0 to 35 No req. GESupplier declared value (S) No requirement Overall 50 to 90 30

48、to 75 15 to 60 No requirement GUSupplier declared value (S) No requirement Overall 47 to 87 No requirement 15 to 75 No requirement GVSupplier declared value (S) No requirement Overall No requirement GNSupplier declared value (S) For the control of individual batches of mixtures, the supplier of cate

49、gories GA, GB, GC, GOand GPshall nominate a supplier declared value within the supplier declared value grading range appropriate to the mixture type. NOTE Use of the supplier declared value is illustrated in Annex A. BS EN 13285:2010EN 13285:2010 (E) 11 4.4.2 Grading of individual batches When required in addition to conforming to the overall grading range given in Table 6, the grad