BS EN 13331-1-2002 Trench lining systems - Product specifications《槽式布线系统 产品规范》.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Trench lining systemsPart 1: Product specificationsBS EN 13331-1:2002Incorporating Corrigendum July 2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13331-1August 2002ICS 93.020English versionTrench lining systems

2、- Part 1: Product specificationsDispositifs de blindage de tranches - Partie 1:Spcification du produitGrabenverbaugerte - Teil 1: ProduktfestlegungenThis European Standard was approved by CEN on 6 July 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the

3、 conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three

4、 official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria,

5、Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Cen

6、tre: rue de Stassart, 36 B-1050 Brussels 2002 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13331-1:2002 ENational forewordThis British Standard is the UK implementation of EN 13331-1:2002.The UK participation in its preparation wa

7、s entrusted to Technical Committee B/514/WG29, Trench support systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct appli

8、cation. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 99066 3ICS 93.020, 91.220 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strateg

9、y Committee on 9 September 2002.Amendments/corrigenda issued since publicationDate Text affected31 July 2017 Missing characters added to web versionBRITISH STANDARDBS EN 13331-1:2002EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13331-1August 2002ICS 93.020English versionTrench lining systems - P

10、art 1: Product specificationsDispositifs de blindage de tranches - Partie 1:Spcification du produitGrabenverbaugerte - Teil 1: ProduktfestlegungenThis European Standard was approved by CEN on 6 July 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co

11、nditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three of

12、ficial versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Bel

13、gium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre

14、: rue de Stassart, 36 B-1050 Brussels 2002 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13331-1:2002 EBS EN 13331-1:2002EN 13331-1:2002 (E)2ContentspageForeword3Introduction .41 Scope 42 Normative references 43 Terms and definitio

15、ns54 Symbols 155 Designation.166 Materials176.1 General176.2 Fasteners 176.3 Minimum fracture elongation of cast iron .177 Requirements .177.1 General177.2 Minimum characteristic system resistance 187.3 Deflection187.4 Attachment points for extracting, handling, pulling and connecting.207.5 Struts.2

16、17.6 Strut to panel or slide rail connection .237.7 Panels238 Assessment249 Instruction manual.249.1 General249.2 Principle contents2410 Marking .2511 Conformity2511.1 Declaration of conformity .2511.2 Evaluation of conformity.26Annex A (normative) Partial safety factors.27Annex B (informative) Rela

17、tionship between loads and resistance 28Annex C (informative) Assessment nomogram for a trench lining system 29Annex D (informative) Explanation of cut and lower techniques .31Bibliography 32BS EN 13331-1:2002EN 13331-1:2002 (E)3ForewordThis document (EN 13331-1:2002) has been prepared by Technical

18、Committee CEN/TC 53 “Temporary worksequipment“, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by February 2003, and conflicting national standards shall be wi

19、thdrawn at the latestby February 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy,

20、Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.EN 13331, Trench lining systems consists of the following parts:Part 1: Product specifications.Part 2: Assessment by calculation or test.These standards are to be read in conjunction with prEN 12811-2

21、and prEN 12811-3 Temporary works equipment-Scaffolds.BS EN 13331-1:2002EN 13331-1:2002 (E)4IntroductionTrench lining systems are intended to ensure the stability of vertical trench walls and to protect workers from theeffects of collapse of the trenches.Part 1 of the series deals with materials and

22、specifications for the manufacture of trench lining systems.Part 2 of the series deals with the evaluation methods using both calculations and tests for trench lining systems.A trench lining system comprises a variety of components, which, when assembled, create trench support. Theinstruction manual

23、 provides all the necessary information on the designation and safe use of trench lining systems.1 ScopeThis European Standard specifies requirements for metallic trench lining systems assembled completely frompurpose made prefabricated components. It includes material, constructional and structural

24、 requirements.Partial safety factors for design refer to annex A.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed her

25、eafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 10002-1, Met

26、allic materials - Tensile testing - Part 1: Method of test at ambient temperature.prEN 12811-2, Temporary works equipment - Scaffolds - Part 2: Information on materials.EN ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screwsand studs (ISO 89

27、8-1:1999)EN 13331-2, Trench lining systems Part 2: Assessment by calculation or test.ENV 1090-1, Execution of steel structures Part 1: General rules and rules for buildings.ENV 1999-1-1, Eurocode 9: Design of aluminium structures Part 1-1: General rules General rules and rules forbuildings.BS EN 133

28、31-1:2002EN 13331-1:2002 (E)53 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1trench lining systemassembly of prefabricated components intended for the support of the vertical faces of trenchesNOTE Main load-bearing components are panels

29、, slide rails and supporting components.3.2types of trench lining system3.2.1centre-supported trench lining system (CS type)system in which pairs or panels are held apart by struts attached at the vertical centre line of the panels (see Figure1)3.2.2edge-supported trench lining system (ES type)syste

30、m in which pairs of panels are held apart by struts attached at the vertical edges of the panels (see Figures 2and 3)3.2.3slide rail trench lining system (R type), single (RS), double (RD) or triple (RT)system in which panels can be moved up and down in single or multiple grooves of pairs of slide r

31、ails held apart bystruts or supporting frames (see Figure 4)3.2.4drag box (DB type)edge-supported trench lining system, intended to be dragged horizontally (see Figure 5)NOTE The leading end has attachment points for pulling and can have cutting edges at the leading end and at the bottom.The clearan

32、ce under the leading end struts can be different to that under the rear strut.BS EN 13331-1:2002EN 13331-1:2002 (E)6Key1 Base assembly2 Top assemblybcInternal trench lining widthFigure 1 Example of a centre supported trench lining system (CS type) with struts with variable lengthadjustment (SV)For t

33、he use of this equipment refer to 7.1.9.BS EN 13331-1:2002EN 13331-1:2002 (E)7Keys1 Panel2 Strut with variable length adjustment3 Cutting edge4 Panel soldier5 Handling pointbcInternal trench lining widthhcBottom strut clearanceFigure 2 Example of an edge-supported trench lining system (ES type) with

34、 struts with variable lengthadjustment (SV)Key1 Panel2 Strut with incremental length adjustment3 Clearance only connection4 Integral panel soldierFigure 3 Example of an edge-supported trench lining system (ES type) with incremental struts andclearance only strut connectionsBS EN 13331-1:2002EN 13331

35、-1:2002 (E)8Key1 Panel2 Slide rail3 Supporting framehcBottom strut clearanceFigure 4 Example of a slide rail trench lining system, double type (RD), with supporting framesBS EN 13331-1:2002EN 13331-1:2002 (E)9Key1 Leading end strut2 Cutting edge3 Pulling pointFigure 5 Example of a drag box (DB type)

36、3.3supporting components3.3.1strut (S)component that resists compressive and tensile forces and may resist moments at the end connections3.3.2strut with variable length adjustment (SV)strut comprising threaded spindles, nuts and extension bars for which rough length adjustment is carried out byaddin

37、g or removing extension bars, while fine length adjustment is achieved by means of the threaded spindles3.3.3strut with incremental length adjustment (SI)strut comprising telescopic tubes with fixing holes and pins and/or extension bars for which only incrementaladjustment is possible3.3.4non adjust

38、able strut (SN)strut with no facility for adjustment3.3.5extension barcomponent used for axial insertion in a strut to increase its lengthNOTE Two basic types of extension bar exist:with flanges at both ends (see Figures 6a and 6b);with a pinned spigot and socket connection (see Figure 6b).3.3.6supp

39、orting frame (FR)component of a slide rail trench lining system that can be installed at any height above the bottom of the trench toresist compressive and tensile forces and bending moments (see Figure 4)BS EN 13331-1:2002EN 13331-1:2002 (E)10a) Strut with variable length adjustment (SV)b) Strut wi

40、th incremental length adjustment (SI)c) Non adjustable strut (SN)Key1 Threaded spindle2Nut3 Extension4 Extension bar with a pinned spigot and socket connection5 Telescopic tubesFigure 6 Example for strut typesBS EN 13331-1:2002EN 13331-1:2002 (E)113.4panel soldiercomponent for distributing load betw

41、een panels and strutsNOTE Panel soldiers are installed in a vertical position and can either be attached to the panels (see Figure 2), or form anintegral part of them (see Figure 3).3.5slide raildiscrete vertical member which has a groove or grooves at two sides to engage with and guide panelsNOTE O

42、pposite rails are connected by struts or supporting frames (see Figure 4)3.6strut to panel or slide rail connection3.6.1articulated strut to panel connection (A)strut connection with mechanical devices to limit the rotation of the strut, at the point where it meets the panel orslide rail (see Figure

43、 7)3.6.2clearance only strut to panel connection (C)strut connection in which the rotation of the strut, at the point where it meets the panel or slide rail, is limited to thatmovement permitted by gaps intentionally provided (see Figure 8)3.6.3fixed strut to panel connection (F)fully restrained str

44、ut to panel or slide rail connection, permitting no free rotation (see Figure 9)Key1 Panel2 Panel soldier3Pin4 Rotation limitation device5Strutd Possible rotation angleFigure 7 Example of an articulated strut to panel connection (A)BS EN 13331-1:2002EN 13331-1:2002 (E)12Key1 Panel2 Panel soldier3Pin

45、4Strut5 Strut to panel connectord Possible rotation angleFigure 8 Example of a clearance only strut to panel connection (C)Key1 Panel2 Panel soldier3Bolts4StrutFigure 9 Example of a fixed strut to panel connection (F)3.7internal trench lining width, bcclear horizontal distance between the panels of

46、a trench lining system (see Figure 2)3.8bottom strut clearance hcvertical distance between the lowest edge of a panel or slide rail and the lowest point of the bottom supportingcomponent (see Figures 2 and 4)BS EN 13331-1:2002EN 13331-1:2002 (E)133.9trench width bdistance between the soil faces3.10b

47、ase assembly (B)assembly of components of a centre- or edge-supported trench lining system that are placed in the trench before allother assembliesNOTE The bottom edges of the panels normally have cutting edges. The clear space, hc bcat the bottom is intended forplacing pipes (see Figures 1 and 2).3

48、.11top assembly (T)assembly of components of a centre- or edge-supported trench lining system intended for use above a basemodule or another top module to support deeper trenches (see Figure 1)3.12characteristic system resistance Rkresistance to an external load of a specific assembly of components

49、of a trench lining system (see annex B)NOTE Multiple configurations, where possible, can produce a variety of characteristic system resistance values for a givenassembly.3.13extracting, handling, pulling and connecting points3.13.1extracting pointpoint to attach lifting gear to enable extraction of trench lining systems3.13.2handling pointpoint for handling components to aid the assembly of the system and for use in transportation3.13.3pulling pointpoint for horizontally pulling drag boxes3.13.4vertical connecting pointpoint for connecting