1、BRITISH STANDARD BS EN 135000:1993 CECC 35000: 1977 Incorporating Amendment Nos. 1 and 2 Harmonized system of quality assessment for electronic components: Generic specification: Travelling wave amplifier tubes The European Standard EN 135000:1992 has the status of a British StandardBSEN 135000:1993
2、 This British Standard, having been prepared under the directionof the Electronic Components Standards Committee, was published underthe authority of the Executive Board on 28February1978 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference ECL/5 Draft fo
3、r comment74/25066DC ISBN0580100812 Cooperating organizations The Electronic Components Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific, industrial and consumer organizations: British E
4、lectrical and Allied Manufacturers Association (BEAMA) Electricity Supply Industry in England and Wales Electronic Components Industry Federation* Electronic Engineering Association Institution of Electronic and Radio Engineers Ministry of Defence* National Supervising Inspectorate* Post Office Soci
5、ety of British Aerospace Companies Limited* Telecommunication Engineering and Manufacturing Association (TEMA) Trades Union Congress The organizations marked with an asterisk in the above list were directly represented on the committee entrusted with the preparation of this BritishStandard. Amendmen
6、ts issued since publication Amd. No. Date of issue Comments 5870 July 1988 7881 August 1993 Indicated by a sideline in the marginBSEN135000:1993 BSI 09-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword ii Text of EN 135000 1 Publications referred to Insi
7、de back coverBSEN 135000:1993 ii BSI 09-1999 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Committee. It is identical with CENELEC Electronic Components Committee (CECC)35000“Harmonized system of quality assessment for electronic
8、 components: Generic specification: travelling wave amplifier tubes”. In 1992 the CENELEC Electronic Components Committee (CECC) accepted CECC35000:1977 as European Standard EN 135000:1992. As a consequence of implementing the European Standard this British Standard is renumbered as BSEN135000 and a
9、ny reference to BS CECC 35000 should be read as a reference to BS EN 135000. This standard gives the terminology, quality assessment procedures and test and measurement procedures applicable to the family of travelling wave amplifier tubes with output power ratings not exceeding500watts. Any blank d
10、etail specification dealing with a particular sub-family of travelling wave amplifier tubes required to be used in conjunction with this standard will select those tests which are considered appropriate to the sub-family and may also give more detailed information relative to the sub-family. This st
11、andard is a harmonized specification within the CECC system. The existing non-harmonized British Standard BS9025 “Travelling wave amplifier tubes of assessed quality: Generic data and methods of test” will eventually be superseded by this standard, but for a period both standards will remain in forc
12、e because of current approvals to BS9025. For the time being, until BS E9000 is published, specifications in the series are subject to the basic rules set down in BS9000 “General requirements for electronic components of assessed quality”. The British Standards Institutions prescribed layout of a de
13、tail specification is given in Part2“Data on generic and detail specifications” of BS9000. Cross references. The British Standard harmonized with CECC00100is BS9000 “General requirements for electronic components of assessed quality”. IEC117substantially agrees in technical content with BS3939 “Grap
14、hical symbols for electrical power, telecommunications and electronics diagrams”. For each of the following references to International Standards that is given in the text, there is a corresponding British Standard; these are as listed below: Reference to International Standard Corresponding British
15、Standard ISO 1000:1973 BS 5555:1976 SI units and recommendations for the use of their multiples and of certain other units IEC 27-1:1971 BS 1991 Letter symbols, signs and abbreviations Part 6:1975 Electrical science and engineering IEC50 (Chapter 531) BS4727 Glossary of electrotechnical, power, tele
16、communication, electronics, lighting and colour terms Part 1:Group 06:1973 Electronic tube terminology IEC68 BS2011 Basic environmental testing procedures IEC134:1961 BS3494 Recommendations on semiconductor devices Part 1:1967 Essential electrical and mechanical ratings and characteristics IEC410:19
17、72 BS6001:1972 Sampling procedures and tables for inspection by attributesBSEN 135000:1993 BSI 09-1999 iii NOTEThere is as yet no equivalent British Standard for IEC151, IEC235 or CECC00107. The committee responsible for this standard has studied these and confirms that, for the purpose of this stan
18、dard, their technical requirements are acceptable. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obl
19、igations. Reference to International Standard Corresponding BritishStandard CECC00006:1973 BS E9006:1976 Harmonized system of quality assessment for electronic components. Basic specification: Environmental test procedures CECC 00007:1973 BS E9007:1975 Harmonized system of quality assessment for ele
20、ctronic components. Basic specification: Sampling plans for inspection by attributes Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, theENtitle page, page 2, the CECC title page, page ii, pages 1 to 6, an inside back cover and a back cover. This standard
21、 has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.iv blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN135000 May1992 UDC Descriptors: Quality, electronic components, travelling wave amplifi
22、er tubes English version Generic specification: Travelling wave amplifier tubes Spcification gnrique: Tubes amplificateurs onde progressive Fachgrundspezifikation: Wanderfeld-Verstrkerrhren This European Standard was approved by CENELEC Electronic Components Committee (CECC) on14 January1992. The te
23、xt of this standard consists of the text of CECC35000 Issue1:1977 (with Amdt.1) of the corresponding CECC Specification. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wi
24、thout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the General Secretariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in an
25、y other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CECC General Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, Franc
26、e, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee fo
27、r Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1992 Copyright reserved to CENELEC members Ref. No. EN 135000:1992 EEN 135000:1992 BSI 09-1999 2 Contents Page
28、Section 1. Scope 1 Section 2. General 2.1 Order of precedence 1 2.2 Related documents 1 2.3 Units, symbols and terminology 2 2.4 Standard and preferred values 2 2.5 Marking 2 Section 3. Quality assessment procedures 3.1 Primary stage of manufacture 2 3.2 Structural similarity 2 3.3 Qualification app
29、roval procedure 3 3.4 Quality conformance inspection 3 3.5 Resubmission of rejected lots 3 3.6 Certified test records 3 3.7 Delayed delivery 3 Section 4. Test and measurement procedures 4.1 General 3 4.2 Alternative methods 3 4.3 Standard conditions for testing 4 4.4 Visual inspection and check of d
30、imensions 4 4.5 Electrical measurement procedures 4 4.6 Environmental test and measurement procedures 4 4.7 Additional test and measurement procedures 5 4.8 Endurance tests, operating and non-operating 5EN 135000:1992 ii BSI 09-1999 Foreword The CENELEC Electronic Components Committee (CECC) is comp
31、osed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications
32、 and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate, of Conformity. The components produced under the System are thereby accepted by all member countries without further testing. This document has been formally approved
33、 by the CECC, and has been prepared for those member countries taking part in the System who wish to issue national harmonized specifications for TRAVELLING WAVE AMPLIFIER TUBES. It should be read in conjunction with document CECC00100: Basic Rules (1974). At the date of printing of this document, t
34、he member countries of the CECC are Belgium, Denmark, Germany, France, Ireland, Italy, the Netherlands, Norway, Sweden, Switzerland and the United Kingdom, and copies of it can be obtained from the National Committees of the CENELEC in these countries. Preface This generic specification was prepared
35、 by CECC Working Group13: “Microwave Tubes”. In accordance with the requirements of document CECC00100it is based, wherever possible, on the Recommendations of the International Electrotechnical Commission and in particular on IEC Publication235: Measurement of the electrical properties of microwave
36、 tubes. The text of this specification was circulated to the CECC for voting in the documents below and was formally approved by the CECC for printing as a CECC Specification. This specification will be supplemented by blank detail specifications specific to each sub-family of travelling wave amplif
37、ier tubes. Document Voting date CECC (Secretariat)266 15Nov1974 CECC (Secretariat)266A 7Nov1975EN135000:1992 BSI 09-1999 1 Section 1. Scope This document relates to travelling wave amplifier tubes. At present, it is limited to CW power amplifier tubes up to 500 watts power output. Section 2. General
38、 2.1 Order of precedence Where any discrepancies occur for any reason, documents shall rank in the following order of authority: the detail specification the generic specification the rules of procedure of document CECC00100or any other international (for example IEC) documents to which reference is
39、 made. NOTEThe same order of precedence shall apply to equivalent national documents. 2.2 Related documents ISO 1000 (1973) SI units and recommendations for the use of their multiples and of certain other units. IEC 27 Letter symbols to be used in electrical technology. 1 (1971) Part 1: General. 1A
40、(1976) First supplement to Publication27-1:1971. IEC 5O International Electrotechnical Vocabulary. IEC 68 Basic environmental testing procedures. (See CECC 00006.) IEC 117 Recommended graphical symbols. IEC 134 (1961) Rating systems for electronic tubes and valves and analogous semiconductor devices
41、. IEC 151 Measurements of the electrical properties of electronic tubes. 1 (1963) Part 1: Measurement of electrode current. 2 (1963) Part 2: Measurement of heater or filament current. 13 (1966) Part 13: Methods of measurement of emission current from hot cathodes for high-vacuum electronic tubes and
42、 valves. 15 (1967) Part 15: Methods of measurement of spurious and unwanted electrode currents. IEC 235 Measurement of the electrical properties of microwave tubes. 1 (1972) Part 1: Terminology. 1A (1975) First supplement to Publication235-1:1972. 2 (1972) Part 2: General measurements. 2A (1974) Fir
43、st supplement to Publication235-2:1972. 2B (1975) Second supplement to Publication235-2:1972. 2C (1976) Third supplement to Publication235-2:1972. 2D (1976) Fourth supplement to Publication235-2:1972. IEC 410 (1973) Sampling plans and procedures for inspection by attributes. (SeeCECC00007.) CECC0010
44、0 (1974) Basic Rules. CECC 00107 (1974) RP7: Quality assessment procedures.EN 135000:1992 2 BSI 09-1999 2.3 Units, symbols and terminology Units, graphical symbols, letter symbols and terminology shall, whenever possible, be taken from the following documents: Where further units, symbols and termin
45、ology are required they shall be derived in accordance with the principles of the documents listed above 2.4 Standard and preferred values Not applicable. 2.5 Marking The following shall be marked on the tube in the following order of precedence as space permits. All this information, except the ter
46、minal marking, shall appear on the primary pack: terminal identification (where this is not shown on the outline drawing) and where appropriate, any special operating conditions type designation date code and/or factory identification code manufacturers name or trade mark mark of conformity unless a
47、 certificate of conformity is used. The use of potentially hazardous material in the construction of the tubes, or other hazards associated with the operation of the tube, shall be indicated according to national requirements. Section 3. Quality assessment procedures 3.1 Primary stage of manufacture
48、 This is the process of joining together of all piece parts. The sub-contracting of this process and/or all subsequent processes is prohibited. (See 7.2.2 of CECC00107. 3.2 Structural similarity When simultaneous or successive production is proceeding on several types of tubes having common features
49、, those common features may be sampled from the complete range. Admissible common features and associated tests include the following: CECC00006 (1973) Basic specification: Environmental test procedures. CECC 00007 (1973) Basic specification: Sampling plans and procedures for inspection by attributes. ISO 1000 SI units and recommendations for the use of their multiples and certain other units. IEC 27 Letter symbols to be used in electrical technology. IEC 50 International Electrotechnical Vocabulary. IEC 117 R
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1