BS EN 13596-2005 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of bond strength《防水用.pdf

1、BRITISH STANDARD BS EN 13596:2004 Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Determination of bond strength The European Standard EN 13596:2004 has the status of a British Standard ICS 91.100.50; 93.080.20 BS EN 13596:

2、2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 21 April 2005 BSI 21 April 2005 ISBN 0 580 45878 4 National foreword This British Standard is the official English language version of EN 13596:2004. The UK participation in its preparation

3、 was entrusted by Technical Committee B/546, Flexible sheets for waterproofing and water vapour control, to Subcommittee B/546/9, Bridge deck waterproofing, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-re

4、ferences The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of Brit

5、ish Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; presen

6、t to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an in

7、side front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN13596

8、October2004 ICS91.100.50;93.080.20 Englishversion FlexiblesheetsforwaterproofingWaterproofingofconcrete bridgedecksandotherconcretesurfacestrafficablebyvehicles Determinationofbondstrength FeuillessouplesdtanchitEtanchitdespontset autressurfacesenbtoncirculablesparlesvhicules Dterminationdeladhrence

9、 AbdichtungsbahnenAbdichtungssystemeaufBetonfr BrckenundandereVerkehrsflchenBestimmungder Abreifestigkeit ThisEuropeanStandardwasapprovedbyCENon8August2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalst

10、andardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertherespon

11、sibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malt

12、a,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved

13、worldwideforCENnationalMembers. Ref.No.EN13596:2004:EEN 13596:2004 (E) 2 Contents page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Test methods5 4.1 Principle5 4.2 Apparatus and materials.5 4.3 Preparation of test specimens .6 4.4 Procedure .7 4.5 Expres

14、sion of results 8 5 Test report 8 EN 13596:2004 (E) 3 Foreword This document (EN 13596:2004) has been prepared by Technical Committee CEN /TC 254 “Flexible sheets for waterproofing“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, eit

15、her by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by July 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im

16、plement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd

17、om. EN 13596:2004 (E) 4 Introduction The purpose of the test is to determine the adhesive properties of the waterproofing system. Bond strength between the waterproofing sheet system and concrete substrate or asphalt layer can be determined. EN 13596:2004 (E) 5 1 Scope This document is one of a seri

18、es of standards applicable to flexible sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles. This document specifies a test method for the evaluation of the tensile bond strength properties of the waterproofing sheet system applied to a concrete surfa

19、ce and with an asphalt layer. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

20、es. EN 13416, Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling EN 13375:2004, Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Specimen preparation. prEN 1469

21、5:2003, Flexible sheets for waterproofing Reinforced bitumen sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Definitions and characteristics. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13375:2

22、004, prEN 14695:2003 and the following apply. bond strength tensile stress at maximum force when testing the adhesion between different layers in a waterproofing system 4 Test methods 4.1 Principle The bond strength shall be measured using a tensile test equipment. The tensile force shall be applied

23、 perpendicular to the test specimen, and the force required at failure shall be registered. 4.2 Apparatus and materials a) Tensile test machine, with force increasing rate control and automatic load recording, fitted with suitable clamps and base to ensure that the tensile force can be applied witho

24、ut momentum perpendicular to the test specimen. b) Circular steel plates, with a diameter of 50 mm, or square steel plates with test area (50 50) mm, and a tolerance of 0,5 mm. The steel plate shall be attached by suitable means (e.g. screwed) to the tensile test machine. Minimum thickness of steel

25、plate shall be 10 mm from bottom of steel plate to bottom of screw hole. c) Suitable adhesive (e.g. two part epoxy resin), for bonding the steel plates to the waterproofing sheet or the asphalt layer of the test specimen. d) Oven, capable of maintaining a temperature of (23 2) C. e) Device for measu

26、ring surface temperature, with an accuracy of at least 0,5 C. EN 13596:2004 (E) 6 4.3 Preparation of test specimens Samples and test pieces shall be taken in accordance with EN 13416. Compound specimen and test specimen preparations are described and specifications for base specimens and asphalt lay

27、er mixes are given in EN 13375. Type 1 (waterproofing sheet and concrete): Base specimen with the applied flexible sheet waterproofing shall be used if bond strength between waterproofing sheet and concrete substrate is to be measured. If the flexible sheet system consists of more than one sheet lay

28、er, only the bottom sheet layer shall be applied and tested. (Illustrated in Figure 1.) Type 2 (waterproofing sheet and asphalt layer): Flexible sheet sample applied with an asphalt layer shall be used if bond strength between waterproofing sheet and asphalt layer is to be measured. If the flexible

29、sheet system consists of more than one sheet layer, only the top sheet layer shall be applied with an asphalt layer and tested. After preparation the compound specimen shall be turned up side down (with the waterproofing facing upwards). Type 3 (concrete, waterproofing system and asphalt layer): Bas

30、e specimen with the applied flexible sheet waterproofing system and asphalt layer shall be used if bond strength of the complete waterproofing system and including the asphalt layer (the weakest link of the system) is to be measured. For type 3 only sawn test specimens 50 mm 50 mm shall be used. Aft

31、er preparation of test specimen(s) according to EN 13375 and cooling to room temperature, steel plates (4.2 b) shall be bonded to the upper surface of the test specimen (waterproofing sheet for type 1 and 2 or asphalt layer for type 3) with a suitable adhesive (4.2 c). For type 1 and 2 the test area

32、s shall then be isolated by cutting the sheet along the sides of the steel plate down to the concrete (type 1) or to the asphalt layer (type 2). Test specimen areas may be cut before bonding the steel plates. At least three test areas shall be prepared and any preparation shall not affect the struct

33、ure of the material. NOTE Enough test specimens should be prepared to ensure a minimum acceptable number of tests with an acceptable type of failure. If necessary the test area surface is prepared, before bonding the steel plates to the surface, by for instance using a metal brush. EN 13596:2004 (E)

34、 7 Key 1 Steel plate 2 Waterproofing sheet 3 Concrete Figure 1 Example of equipment and specimen for determining bond strength (between waterproofing sheet and concrete substrate) 4.4 Procedure Prior to testing the test specimen shall be conditioned at test temperature for at least 24 hours. The tes

35、t specimen is placed in the tensile test machine and the steel plate attached to the machine. During testing the steel plate is pulled with an increasing stress rate to assure an increase in tensile force of (0,15 0,01) N/s mm 2applied perpendicular to the test specimen. The tensile bond failure loa

36、d shall be recorded together with the mode of failure. The following general modes of failure may occur for a system of flexible bitumen sheet and primer: in the concrete; between concrete and primer; in the primer layer; between primer and weldable or pour-and roll bitumen; in the weldable or pour-

37、and roll bitumen; against or within the reinforcement; between sheet and granules; adhesive failure. With an applied flexible sheet waterproofing system and asphalt layer failure may occur also: between asphalt layer and sheet; EN 13596:2004 (E) 8 in the asphalt layer. The test is carried out at (23

38、 2) C. NOTE 1 Additionally other temperatures can be used if required. Three valid tests shall be carried out for each test temperature. The mean bond strength shall be calculated from a minimum of three accepted test results. The surface temperature shall be measured for each test area immediately

39、after finishing the test. NOTE 2 The result of the test depends significantly on the test temperature. 4.5 Expression of results 4.5.1 Method of calculation Bond strength shall be calculated, to the nearest 0,1 N/mm 2 , as the stress at maximum force by the following equation: max= F max/ A where ma

40、xis the bond strength at failure, in N/mm ; F maxis the maximum force, in N; A is the test area, in mm . The arithmetical mean value of the three test results shall be calculated. 4.5.2 Precision of the test method The precision of the test method is not specified. 5 Test report The test report shal

41、l include at least the following information: a) all details necessary to identify the product tested and identification of the whole waterproofing system including asphalt layer and application temperature, type and quantity of the primer; b) a reference to this document (EN 13596) and any deviatio

42、n from it; c) information on preparation of test specimens in accordance with 4.3 and EN 13375, specimens prepared by and witnessed by which organisation; d) information about the procedure in accordance with Clause 4.4, test temperature, surface temperature and test area; e) the test results and fa

43、ilure mode according to Clause 4.5 for each individual test, mean value if relevant; f) the dates of delivery and preparation of specimens; g) the date of tests. blankBS EN 13596:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body resp

44、onsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amen

45、dments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be f

46、ound on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign stan

47、dards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementatio

48、n of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info