BS EN 13709-2010 Industrial valves - Steel globe and globe stop and check valves《工业用阀 钢制球阀、球状截止阀和止回阀》.pdf

1、BS EN 13709:2010ICS 23.060.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDIndustrial valves Steel globe and globestop and check valvesThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISB

2、N 978 0 580 68322 0Amendments/corrigenda issued since publicationDate CommentsBS EN 13709:2010National forewordThis British Standard is the UK implementation of EN 13709:2010. Itsupersedes BS EN 13709:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee

3、 PSE/18/2, Industrial valves, steam traps, actuators andsafety devices against excessive pressure - Gate, globe, diaphragm andcheck valves.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary p

4、rovisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 13709:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13709 May 2010 ICS 23.060.10 Supersedes EN 13709:2002English Version Industri

5、al valves - Steel globe and globe stop and check valves Robinetterie industrielle - Robinets soupape et robinets clapet libre blocable en acier Industriearmaturen - Absperrventile und absperrbare Rckschlagventile aus Stahl This European Standard was approved by CEN on 9 April 2010. CEN members are b

6、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

7、 CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same s

8、tatus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

9、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means

10、reserved worldwide for CEN national Members. Ref. No. EN 13709:2010: EBS EN 13709:2010EN 13709:2010 (E) 2 Contents page Foreword 31 Scope 42 Normative references 43 Terms and definitions . 54 Requirements . 64.1 Design . 64.1.1 Materials . 64.1.2 Pressure/temperature ratings . 64.1.3 Dimensions . 64

11、.1.4 Operation 84.1.5 Auxiliary connections . 84.1.6 Obturator 104.1.7 Permanent joining 104.2 Functional characteristics 104.2.1 Shell design strength 104.2.2 Flow characteristics 104.2.3 Allowable differential pressure 114.2.4 Seat tightness 114.2.5 Sizing the operating element 125 Test procedures

12、 . 126 Declaration of compliance 127 Designation 128 Marking and preparation for storage and transportation 138.1 Marking . 138.2 Preparation for storage and transportation 13Annex A (informative) Information to be supplied by the purchaser 14Annex ZA (informative) Relationship between this European

13、 Standard and the Essential Requirements of EU Directive 97/23/EC . 15Bibliography 16BS EN 13709:2010EN 13709:2010 (E) 3 Foreword This document (EN 13709:2010) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard sh

14、all be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this

15、document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13709:2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade As

16、sociation, and supports essential requirements of EU Directive 97/23/EC. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. This document supersedes EN 13709:2002 where the following modifications were made: the normative references were updated

17、 in Clause 2, in 4.1.1, in 4.1.2, in 4.1.3, in 4.1.7.1, in 4.2.1, in 4.2.4 and in 5.1; in Table ZA.1, sub-clause 4.1 (instead of Clause 4) was correlated to PED Annex I, section 2.1. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries ar

18、e bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Sp

19、ain, Sweden, Switzerland and the United Kingdom. BS EN 13709:2010EN 13709:2010 (E) 4 1 Scope This European Standard specifies the requirements for steel globe and globe stop and check valves which are wrought, cast or fabricated in straight, angle or oblique pattern with end connections flanged, but

20、t welding, socket welding or threaded. This standard is applicable to steel globe and globe stop and check valves mainly used for industrial and general purpose applications. However, they can be used for other applications provided the requirements of the relevant performance standards are met. The

21、 range of nominal sizes covered is: DN 8; DN 10; DN 12; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400. DN 8 and DN 12 are not used for PN designated flanged end connections. DN 8, DN 10 and DN 12 are not used for Class designat

22、ed flanged end connections. Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65. The range of pressure designations covered is: a) for flanged and butt welding end valves: 1) PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; 2) Class 150; Class 300; Class 600. b) for so

23、cket welding end valves and threaded end valves: 3) PN 40; PN 63; PN 100; 4) Class 600; Class 800. NOTE Class 800 is a Class designation widely used for socket welding and threaded end valves. 2 Normative references The following referenced documents are indispensable for the application of this doc

24、ument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19, Industrial valves Marking of metallic valves EN 287-1:2004, Qualification test of welders Fusion welding Part 1: Steels EN 558

25、, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 736-1:1995, Valves Terminology Part 1: Definition of types of valves EN 736-2:1997, Valves Terminology Part 2: Definition of components of valves EN 736-3:

26、2008, Valves Terminology Part 3: Definition of terms BS EN 13709:2010EN 13709:2010 (E) 5 EN 1092-1:2007, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part 1: Steel flanges EN 1418, Welding personnel Approval testing of welding operators for fus

27、ion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials EN 1759-1, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 1: Steel flanges, NPS to 24 EN 10045-1, Metallic materials Charpy impact te

28、st Part 1: Test method EN 12266-1:2003, Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2:2002, Industrial valves Testing of valves Part 2: Tests, test procedures and acceptance criteria Supplementary requirements EN

29、 12351, Industrial valves Protective caps for valves with flanged connections EN 12516-1, Industrial valves Shell design strength Part 1: Tabulation method for steel valve shells EN 12516-2, Industrial valves Shell design strength Part 2: Calculation method for steel valve shells EN 12516-3, Industr

30、ial valves Shell design strength Part 3: Experimental method EN 12570, Industrial valves Method for sizing the operating element EN 12627, Industrial valves Butt welding ends for steel valves EN 12760, Valves Socket welding ends for steel valves EN 12982, Industrial valves End-to-end and centre-to-e

31、nd dimensions for butt welding end valves EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 5210, Industrial valves Multi-turn valve actuator attachments (ISO 5210:1991) EN ISO 15607, Specifi

32、cation and qualification of welding procedures for metallic materials General rules (ISO 15607:2003) ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ASME B1.20.1-1983, Pipe Threads, General Purpose (Inch) 3 Terms and defin

33、itions For the purposes of this document, the definitions of types of valves and components and the terms and definitions given in EN 736-1:1995, EN 736-2:1997 and EN 736-3:2008 apply. NOTE The terms maximum allowable pressure, PS, and test pressure, PT, defined in EU Directive 97/23/EC (PED) are eq

34、uivalent to the terms allowable pressure, ps, and test pressure, pt, defined in EN 736-3:2008. BS EN 13709:2010EN 13709:2010 (E) 6 4 Requirements 4.1 Design 4.1.1 Materials 4.1.1.1 The body and bonnet materials shall be selected from the grades listed in EN 12516-1. 4.1.1.2 All the internal parts in

35、 contact with the fluid shall be made of a material whose corrosion resistance to the fluid being carried is at least equal to the body and bonnet material. 4.1.1.3 Trim materials shall have a chemical composition and mechanical properties, which ensure the mechanical integrity of the valve. The tri

36、m comprises the following: a) stem; b) obturator seat; c) body seat; d) backseat (for valves DN 50 and above, when fitted). 4.1.1.4 Stems shall be manufactured from forged, drawn or rolled material. They shall have a minimum corrosion resistance equivalent to a 13 % chromium content ferritic steel.

37、4.1.2 Pressure/temperature ratings 4.1.2.1 The pressure/temperature ratings shall be as specified in EN 12516-1 for the particular body/bonnet material group. 4.1.2.2 The pressure temperature ratings applicable to Class 800 socket welding and threaded end valves shall be the Class 600 rating for the

38、 applicable material group multiplied by the ratio of 800 : 600. 4.1.2.3 Restrictions of temperature and pressure below those specified in 4.1.2.1 and 4.1.2.2 for example, those imposed by soft seals, special trims and bellows seal shall be indicated on the valve (see 8.1.2). 4.1.2.4 For temperature

39、s below the lowest temperature shown in the pressure/temperature rating tables in EN 12516-1 the maximum allowable pressure shall be no greater than the pressure corresponding to the lowest temperature in the rating tables. The use of valves at lower temperatures than shown in the rating tables is p

40、ermitted providing the bending rupture energy of the body and bonnet material measured on three 10 mm x 10 mm specimens, in accordance with EN 10045-1, shall be no less than an average of 27 J at a temperature no higher than the lowest scheduled operating temperature. 4.1.3 Dimensions 4.1.3.1 Face-t

41、o-face, centre-to-face, end-to-end and centre-to-end dimensions Face-to-face and centre-to-face dimensions for PN and Class designated flanged end valves shall be in accordance with EN 558. The end-to-end and centre-to-end dimensions of butt welding end valves shall be in accordance with EN 12982. T

42、he end-to-end and centre-to-end dimensions of socket welding and threaded end valves are at the choice of the manufacturer. BS EN 13709:2010EN 13709:2010 (E) 7 4.1.3.2 Body end 4.1.3.2.1 Flanged ends shall comply with the requirements of EN 1092-1 for PN designated flanges or EN 1759-1 for Class des

43、ignated flanges. Flanged ends shall be cast or forged integral with the body except that flanges may be attached by welding in accordance with 4.1.7. A full penetration butt weld shall be used for the attachment of flanges by welding on sizes larger than DN 50. 4.1.3.2.2 Butt welding end profiles sh

44、all be in accordance with EN 12627. 4.1.3.2.3 Socket welding end dimensions shall be in accordance with EN 12760. The minimum thickness of the pressure retaining material shall be in accordance with EN 12516-1 or EN 12516-2. 4.1.3.2.4 Threaded ends shall be of the internal form in accordance with Ty

45、pe Rc and Rp to ISO 7-1:1994 or Type G to EN ISO 228-1:2003 or Type NPT to ASME B1.20.1-1983. 4.1.3.3 Body end port inside diameter The body end port shall be circular. For unlined valves, the body end port inside diameter shall be not less than the nominal inside diameter specified in Table 1. Tabl

46、e 1 Nominal inside diameter of the body end port Dimensions in millimetres DN PN 10 PN 16 Class 150 PN 25 PN 40 Class 300 PN 63 PN 100 Class 600 Class 800 8 8 8 6 8 8 6 8 6 6 6 10 10 10 9 10 10 9 10 9 9 9 12 12 12 12 12 12 12 12 11 11 11 15 15 15 13 13 13 13 13 13 13 12 20 20 20 19 19 19 19 19 19 19

47、 18 25 25 25 25 25 25 25 25 25 25 23 32 31 31 31 31 31 31 31 31 31 30 40 40 40 38 38 38 38 38 38 38 36 50 50 50 50 50 50 50 50 50 50 46 65 63 63 63 63 63 63 63 63 63 60 80 78 78 76 76 76 76 76 76 76 - 100 100 100 101 100 100 101 100 100 101 - 125 125 125 127 125 125 127 125 125 127 - 150 150 150 152

48、 150 150 152 150 150 152 - 200 200 200 203 200 200 203 200 199 199 - 250 250 250 254 250 250 254 250 247 247 - 300 300 300 304 300 300 304 300 298 298 - 350 343 343 336 336 336 336 336 327 327 - 400 394 394 387 387 387 387 384 375 375 - BS EN 13709:2010EN 13709:2010 (E) 8 4.1.4 Operation 4.1.4.1 Ste

49、m operating thread The operating thread of the stem shall be of the outside screw type unless otherwise specified by the purchaser. 4.1.4.2 Operating device Unless otherwise specified by the purchaser the valve shall be supplied with a handwheel. If the valve is to be operated by an actuator then the valve/actuator attachment shall be in accordance with EN ISO 5210. 4.1.4.3 Operating direction