BS EN 137101-1996 Harmonized system of quality assessment for electronic components - Blank detail specification - Fixed aluminium electrolytic a c capacitors with non-solid electri.pdf

1、BRITISH STANDARD BS EN 137101:1996 Harmonized system of quality assessment for electronic components Blank detail specification Fixed aluminium electrolytic a.c. capacitors with non-solid electrolyte for motor starter applications (Qualification approval) The European Standard EN137101:1995 has the

2、status of a British StandardBSEN 137101:1996 BSI 11-1999 ISBN 0 580 25773 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/40, Capacitors and resistors for electronic equipment, to Subcommittee EPL/40/1, Capacitors a

3、nd EMI suppression components for electronic equipment, upon which the following bodies were represented: BSI Testing Services Electrical Installation Equipment Manufacturers Association Federation of the Electronics Industry Ministry of Defence National Supervising Inspectorate (BSI-PC) Society of

4、British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBSEN 137101:1996 BSI 11-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 137101 3BSEN 137101:1996 ii BSI 11-1999 National foreword This British Standard

5、 has been prepared by Sub-committee EPL/40/1, and is the English language version of EN137101:1995: Blank detail specification: Fixed aluminium electrolytic a.c. capacitors with non-solid electrolyte for motor starter applications Qualification approval, published by the Electronic Components Commit

6、tee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). This standard lists the requirements which shall be included in any detail specification for this type of capacitor. Detail specifications shall conform to the requirements of this blank detail specification and BS

7、CECC00111 Rule of Procedure11. Specifications Part4:1991 Regulations for CECC detail specifications. The British Standard which implements the CECC Rules of Procedure is BS9000 General requirements for a system for electronic components of assessed quality Part2:1996 Specification for the national i

8、mplementation of the CECC system. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-r

9、eferences International Standard Corresponding British Standard EN137000:1995 BS EN137000:1996 aGeneric specification: Fixed aluminium electrolytic a.c. capacitors with non-solid electrolyte for use with motors. EN137100:1995 BS EN137100:1996 aSectional specification: Fixed aluminium electrolytic a.

10、c. capacitors with non-solid electrolyte for motor starter applications Qualification approval a In preparation Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, the EN title page, pages2 to10 and a back cover. This standard has been updated (see copyright

11、date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN137101 October1995 English version Blank Detail Specification: Fixed aluminium electrolytic a.c. capacitors with non-solid elect

12、rolyte for motor starter applications Qualification approval Spcification particulire cadre: Condensateurs lectrolytiques pour courant alternatif, laluminium, lectrolyte non solide, pour application dans les dmarreurs de moteur Homologation Vordruck fr Bauartspezifikation: Aluminium-Elektrolyt-Wechs

13、el- spannungskondensatoren mit flssigem Elektrolyten zur Verwendung im Motoranlabetrieb Bauartanerkennung This European Standard was approved on1995-06-24. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard t

14、he status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, G

15、erman). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denma

16、rk, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechn

17、ische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC members Ref. No. EN137101:1995 EEN 137101:1995 BSI 11-1999 2 Foreword This European Standard was prepared by Working Group CLC/TC CECC/WG3. The text of the draft based on document CECC(Secretari

18、at)3249 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3661, it was approved as EN137101 on1995-06-24. The following dates were fixed: Contents Page Foreword 2 Introduction 3 1 General data 5 2 Inspection requirements 6 Table 1 5 Table 2 Va

19、lues of capacitance related to case sizes 5 Table 3 Other characteristics 6 Table 4A Test schedule for lot-by-lot tests (group A and B inspection) assessment level E 6 Table 4B Test schedule for periodic tests (group C inspection) assessment level E 7 latest date by which the EN has to be implemente

20、d at national level by publication of an identical national standard or by endorsement (dop) 1996-07-01 latest date by which the national standards conflicting with the EN haveto be withdrawn (dow) 1997-07-01EN 137101:1995 BSI 11-1999 3 Introduction Blank detail specification A blank detail specific

21、ation is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. In the preparation of detail specifications the content of1.4 of the sectional specification shall be taken into account. Identification of th

22、e detail specification and of the component The first page of the detail specification should have the layout recommended on page4 of this blank detail specification. The numbers between the brackets correspond to the following information which shall be inserted at the position indicated: 1 The nam

23、e of the National Standards Organization under whose authority the detail specification is published and, if applicable, the organization from whom the detail specification is available. 2 The CECC symbol and the number allotted to the detail specification by the CECC General Secretariat. 3 The numb

24、er and issue number of the CECC generic or sectional specification as relevant; also national reference if different. 4 If different from the CECC number, the national number of the detail specification, date of issue and any further information required by the national system, together with any ame

25、ndment numbers. 5 A brief description of the component or range of components. 6 Information on typical construction (when applicable). For5 and6 the text to be given in the detail specification should be suitable for an entry in CECC00200 (Register of Approvals) and CECC00300 (Register of National

26、Documents). 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the appropriate national or international documents for outlines. Alternatively the drawing may be given in an annex to the detail specification, but7 should always contain an illust

27、ration of the general outer appearance of the component. 8 The level(s) of quality assessment covered by the detail specification, as appropriate. 9 Reference data giving information on the most important properties of the component which allow comparison between the various component types intended

28、 for the same, or for similar applications.EN 137101:1995 4 BSI 11-1999 1 2 CECC37101-XXX 4 3 ELECTRONIC COMPONENTS OF ASSESSED QUALITY DETAIL SPECIFICATION IN ACCORDANCE WITH: 7 5 Outline drawing (. . . angle projection): FIXED ALUMINIUM ELECTROLYTIC A.C. CAPACITORS WITH NON-SOLID ELECTROLYTE FOR M

29、OTOR STARTER APPLICATIONS 6 TYPICAL CONSTRUCTION (Examples): cylindrical/rectangular metallic/non metallic case insulated/non insulated case solder/screw terminations 8 (Other shapes are permitted within the dimensions given, see Table 1) ASSESSMENT LEVEL: E For notes see page3 9 REFERENCE DATA : In

30、formation about manufacturers who have components qualified to this detail specification is available in the current CECC00200: Register of Firms, Products and Services Approved under the CECC System (Register of Approvals).EN 137101:1995 BSI 11-1999 5 1 General data 1.1 Method of mounting for vibra

31、tion test See1.3.2 of EN137100. 1.2 Dimensions Table 1 1.3 Ratings and characteristics Table 2 Values of capacitance related to case sizes 1.4 Related documents 1.5 Marking The marking of the capacitor and the packing shall be in accordance with the requirements of1.5 of EN137100. NOTEThe details of

32、 the marking of the component and packing shall be given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by this specification shall contain, in clear or coded form, the following minimum information: a) Rated capacitance b) Tolerance on rated capacitance

33、c) Rated a.c. voltage d) Rated duty cycle e) Number and issue reference of detail specification and style reference. Case size reference Dimensions (in mm) D L H d NOTE 1When there is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Tabl

34、e 1. NOTE 2The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. Capacitance range (See Table 2) Tolerance on rated capacitance Rated voltage (See Table 2) Climatic category Rated temperature Tangent of loss angle Vibration test severity Insulation resistance

35、 (if applicable) Rated capacitance (4F) Rated voltage (V r.m.s.) Case size Case size Generic specification EN137000:1995 Sectional specification EN137100:1995EN 137101:1995 6 BSI 11-1999 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purp

36、oses) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTEAdditions or increased requirements should be specified only when essential. Table 3 Other characteristics 2 Inspection requirements 2.1 Procedures 2.1.1 For qualificatio

37、n approval the procedures shall be in accordance with3.4 of EN137100. 2.1.2 For Quality Conformance Inspection the test schedules (Table 4A and Table 4B) include sampling, periodicity, severities and requirements. The formation of inspection lots is covered by3.5.1 of EN137100. Table 4A Test schedul

38、e for lot-by-lot tests (group A and B inspection) assessment level E This table is to be used for defining characteristics which are additional to or more severe than those given in the sectional specification. Notes see end of table Clause number and test 1) Conditions of test 1) IL AQL % Performan

39、ce Requirements 1) 2) Group A1 Non-destructive S4 2,5 4.2 4.2 Visual examination Dimensions (gauging) As in4.2 Marking legible as specified in1.5 of this specification See Table 1 of this specification Group A2 Non-destructive II 1,0 4.9 4.3.1 4.3.2 4.3.4 4.3.5 Sealing Capacitance Tangent of lossang

40、le Voltage proof between terminations Voltage proof between terminations andcase Duration:8h Temperature: rated maximum temperature+10 C Applied voltage: U RV r.m.s. Frequency: f RHz Applied voltage: U RV r.m.s. Frequency: f RHz Applied voltage: 1,2 U RV r.m.s. Duration:2s Applied voltage: 2 U R +10

41、00 V r.m.s but not less than 2000 V r.m.s. No see page of electrolyte or filling material Within specified tolerance k 0,15 No breakdown No breakdown or flashoverEN 137101:1995 BSI 11-1999 7Table 4A Test schedule for lot-by-lot tests (group A and B inspection) assessment level E Table 4B Test schedu

42、le for periodic tests (group C inspection) assessment level E Clause number and test 1) Conditions of test 1) IL AQL % Performance Requirements 1) 2) Group B1 Non-destructive 4) S3 2,5 4.6 4.3.2 4.3.3 Solderability 3) Tangent of loss angle Insulation resistance of external insulation (if applicable)

43、 Method:. . . 5) Applied voltage: U RV r.m.s. Frequency: f RHz Good tinning as evidenced by free flowing of the solder with wetting of the terminations k 0,15 k 100M7 NOTE 1Clause numbers of test and conditions/requirements refer to the sectional specification EN137100 NOTE 2IL=inspection level AQL=

44、acceptable quality level NOTE 3Not applicable to capacitors with terminations not designed for connections by soldering NOTE 4Group B1 is considered non-destructive provided that the requirements of Group A1 and A2 are satisfied. NOTE 5To be specified in the detail specification Notes See end of tab

45、le Clause number and test 1) Conditions of test 1) p n c Performance Requirements 1) 2) Group C1A Destructive 6 9 1 4.2 4.4.1 4.4 4.5 4.5.2 Dimensions (detail) Initial measurements Robustness of terminations Resistance to soldering heat 3) Final measurements Capacitance Visual examination Method:. .

46、 . 5) Severity:. . . 5) No pre-drying Method:. . . 5) Visual examination Capacitance See Table 1 of this specification Within specified tolerance No visible damage No visible damage Marking legible |%C/C|k 5% of the value measured in4.4.1EN 137101:1995 8 BSI 11-1999Table 4B Test schedule for periodi

47、c tests (group C inspection) assessment level E Clause number and test 1) Conditions of test 1) p n c Performance Requirements 1) 2) Group C1B Destructive 6 18 1 4.6 4.7.1 4.7 4.7.3 4.8 4.8.2 Solderability 3) Initial measurements Rapid change of temperature Final measurements Vibration Final measure

48、ments Method:. 5) Capacitance T A : rated minimum temperature T B : rated maximum temperature Five cycles Duration t 1 :30min or3h Recovery:16h to32h Visual examination Method of mounting: See1.1 of this specification Endurance by sweeping Frequency range: . . . . Hz to. . . . Hz 5) Amplitude:. . .

49、. or acceleration:. . . m/s 25) (whichever is less severe) Total duration:. . . sweep cycles 5) Visual examination Capacitance Good tinning as evidenced by free flowing of the solder with wetting of the terminations Within specified tolerance No leakage of electrolyte or filling material, or other visible damage No leakage of electrolyte or filling material, or other visible damage Marking legible |%C/C|k 5% of the value measured in4.7.1 unless otherwise specified in