BS EN 13759-2012 Furniture Operating mechanisms for seating and sofa-beds Test methods《家具 座椅和沙发床的操作机构 试验方法》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFurniture Operating mechanisms for seating and sofa-beds Test methodsBS EN 13759:2012National forewordThis British Standard is the UK implementation of EN 13759:2012. It supersed

2、es DD ENV 13759:2001 which is withdrawn.BSI, as a member of CEN, is obliged to publish EN 13759 as a BritishStandard. However, attention is drawn to the fact that during the development of this European Standard, the UK voted against its approval as a European Standard.The reason for this vote by th

3、e UK Technical subcommittee FW/0/2, Domesticand Contract Furniture is due to concerns that the test dummy defined inclause 4.1 might not be suitable for all types of reclining chair.The UK participation in its preparation was entrusted by Technical CommitteeFW/0, Furniture, to subcommittee FW/0/2, D

4、omestic and Contract Furniture.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution

5、 2012Published by BSI Standards Limited 2012ISBN 978 0 580 68431 9ICS 97.140Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 November 2012.Amendments issued sinc

6、e publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 13759:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13759 April 2012 ICS 97.140 Supersedes ENV 13759:2000English Version Furniture - Operating mechanisms for seating and sofa-beds - Test methods Meubles - Mcanismes de manoeuvre

7、 des siges et des canaps - Mthodes dessai Mbel - Funktionsmechaniken fr Sitzmbel und Liegesofas - Prfverfahren This European Standard was approved by CEN on 9 March 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

8、 Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (E

9、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu

10、m, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEA

11、N COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13759:2012: EBS EN 13759:2012EN

12、 13759:2012 (E) 2 Contents Page Foreword 31 Scope 42 Terms and definitions .43 General test conditions .53.1 Preliminary preparation 53.2 Tolerances 54 Test apparatus .55 Test procedure .75.1 Functional assessment .75.2 Durability test .75.2.1 Set up procedure .75.2.2 Furniture not occupied during o

13、peration of mechanism 75.2.3 Furniture occupied during operation of the mechanism .76 Test report 8BS EN 13759:2012EN 13759:2012 (E) 3 Foreword This document (EN 13759:2012) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standa

14、rd shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of th

15、is document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes ENV 13759:2000. Compared to ENV 13759:2000 the following modifications have been made: a) Modification of the title to better refl

16、ect the content of the standard; b) The test dummy has been totally revised to better integrate with all types of seating; c) The test dummy loading has been modified to a single loading equivalent to a 110 kg person; d) A note has been added to give guidance on how to test chairs for heavier users;

17、 e) A duty cycle has been added for powered reclining mechanisms. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Es

18、tonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13759:2012EN 13759:2012 (E) 4 1 Scope This European St

19、andard specifies test methods for the determination of the durability of hand and power operated reclining mechanisms for adult seating. It also specifies test methods for the determination of the durability of mechanisms for converting sofas and chairs into beds. The test methods are based on use b

20、y a person weighing up to 110 kg. Requirements for the durability of reclining mechanisms are not included within this standard. Test methods for strength and durability of the structure are not included. It does not apply to the safety of electrically driven seating which is covered by the machiner

21、y, low voltage and EMC directives. It does not apply to tilting and reclining mechanisms fitted to work chairs. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 work chair chair, with or without arm rests, for use by one adult in the office or

22、 home office (for example for working with a computer), whose upper part, which includes the seat and back, is supported on a single column and can rotate in the horizontal plane and is at least adjustable in height 2.2 convertible sofa-bed item of seating that utilises a mechanism to convert it int

23、o a bed 2.3 reclining chair item of seating that features a backrest that can be adjusted from the normal upright position to a reclined position Note 1 to entry: The item of seating may also feature a footrest that raises as the back is reclined. The mechanism may be motorised, manual or gravity ac

24、tivated. 2.4 rise and recline chair item of seating that, in addition to the recline function, features a mechanism to raise the seat to ease the process of getting out of the seat 2.5 duty cycle length of time an electrically powered operating mechanism may be operated without impairing its useful

25、life Note 1 to entry: The duty cycle includes the amount of time the drive system may be operated as well as the amount of time it must not be operated to allow the drive system to cool sufficiently before it is activated again. BS EN 13759:2012EN 13759:2012 (E) 5 3 General test conditions 3.1 Preli

26、minary preparation The furniture shall be tested in the condition in which it is delivered. Where assembly is required, the furniture shall be assembled according to the instructions supplied. If the test unit can be assembled in different ways, the most adverse configuration shall be used. If assem

27、bly instructions are not supplied, the assembly method shall be recorded in the report. Fittings shall be tightened before testing and shall not be re-tightened unless specifically required by the manufacturer. The tests shall be carried out indoors in ambient conditions at a temperature between 15

28、C to 25 C. If during a test the temperature is outside the range of 15 C to 25 C, the maximum and/or minimum temperature shall be recorded in the test report. 3.2 Tolerances Unless otherwise stated, the following tolerances are applicable to the test equipment: Forces 5% of the nominal force; Veloci

29、ties 5% of the nominal velocity; Masses 1% of the nominal mass; Dimensions 1 mm of the nominal dimension. NOTE For the purposes of an uncertain measurement, the test results are not considered to be adversely affected when the above tolerances are met. 4 Test apparatus 4.1 Test dummy For seating occ

30、upied during operation the test dummy shown in Figure 1 shall be utilised. The test dummy shall be manufactured from a smooth, rigid material. The sections shall be connected together via a hinging mechanism that does not inhibit the movement of the dummy sections relative to each other. The total m

31、ass of the dummy including any hinge mechanisms shall be 100 kg. For seating occupied during operation, the weight distribution of the sections of the test dummy shall be in accordance with Table 1: Table 1 Test dummy section including appropriate hinge mechanism Weight distribution Head 5 % Upper b

32、ody 54 % Upper leg 24 % Lower leg 17 % BS EN 13759:2012EN 13759:2012 (E) 6 For the dummy shown in Figure 1, all dimensions shall be subject to a 2 mm tolerance. All edges and corners in contact with the item or seating shall have a 12 mm radius. NOTE For items of furniture designed to be used by hea

33、vier people, the weight of the user can be distributed using the weight distribution pattern shown. Dimensions in millimetres Key 1 Hinge point Figure 1 Test dummy BS EN 13759:2012EN 13759:2012 (E) 7 5 Test procedure 5.1 Functional assessment In order to determine the appropriate test procedure(s) f

34、or the item of seating, the functional operation(s) shall be examined. The examination shall be used to describe the manner of operation of the item of seating. The description shall include at least the following: means of operation (e.g. power, body movement), stages of operation, time taken to ca

35、rry out operation(s), and wherever possible, the forces exerted. For seating: a) actions required to recline/tilt the item of seating (including the release of locking devices), such as pressing the arms and thereby reducing the load on the seat, or other ways of moving the weight of the test person

36、 from one part of the item of seating to another; b) actions required to bring the item of seating to the upright position including for example, an extra load being applied to the foot rest, or other ways of moving the weight of the test person from one part of the item of seating to another. For c

37、onvertible sofa-beds: c) actions required to convert the bed into a sofa, d) actions required to convert a sofa into a bed. 5.2 Durability test 5.2.1 Set up procedure Testing shall be carried out as closely to the manner of operation described (see 5.1) as is practically possible, and sufficiently s

38、lowly to ensure that kinetic heating does not occur. For electrically operated seating, the cycle rate shall be the cycle rate recommended by the manufacturer. When the duty cycle is not recommended by the manufacturer, the rate shall be “three cycles on and then off for the equivalent time it takes

39、 to run fifteen cycles“. NOTE The duty cycle may be increased when temperature control is agreed upon with the manufacturer. 5.2.2 Furniture not occupied during operation of mechanism The mechanisms shall be operated for the required number of cycles. 5.2.3 Furniture occupied during operation of the

40、 mechanism The mechanisms shall be operated with the item of seating loaded in accordance with 4.1 for the required number of cycles. BS EN 13759:2012EN 13759:2012 (E) 8 Seating which can be operated both when the item of seating is occupied and when there is no one in the item of seating shall be t

41、ested as described for furniture occupied during operation of the mechanism. 6 Test report The test report shall include at least the following information: a) a reference to this European Standard; b) details of the item of furniture and mechanism tested, including the manner of operation; c) detai

42、ls of defects observed before testing; d) a description of the test procedure and equipment; e) the test results; f) the name and address of the test facility; g) the date of the test. BS EN 13759:2012This page deliberately left blankBSI is the independent national body responsible for preparing Bri

43、tish Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British

44、Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendment

45、s or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on th

46、e inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and

47、 PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Custome

48、r Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of informatio

49、n on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Te