BS EN 13836-2006 Gas fired central heating boilers - Type B boilers of nominal heat input exceeding 300 kW but not exceeding 1 000 kW《燃气集中供热锅炉 公称热输入超过300kW不超过1000KW的B型锅炉》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58nominal heat input exceeding 300 kW, but not exceeding 1 000 kWThe European Standard EN 13836:2006

2、has the status of a British StandardICS 91.140.65Gas fired central heating boilers Type B boilers of BRITISH STANDARDBS EN 13836:2006BS EN 13836:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49300 8A

3、mendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis Br

4、itish Standard was published by BSI. It is the UK implementation of EN 13836:2006.The UK participation in its preparation was entrusted to Technical Committee GSE/29, Gas-fired central heating boilers (domestic and non-domestic) and domestic gas-fired water heaters.A list of organizations represente

5、d on GSE/29 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13836August 2006ICS 91.140.65English VersionGas fired central heating boilers - Type B boilers of nominal heatinput exceeding 300 kW, but not exceeding 1 000 kWChaudires de chauffage central uti

6、lisant les combustiblesgazeux - Chaudires de type B dont le dbit calorifiquenominal est suprieur 300 kW mais infrieur ou gal 1000 kWHeizkessel fr gasfrmige Brennstoffe - Heizkessel desTyps B mit einer Nennwrmebelastung grer als 300 kWaber gleich oder kleiner als 1 000 kWThis European Standard was ap

7、proved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationals

8、tandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified t

9、o the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

10、way, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form an

11、d by any means reservedworldwide for CEN national Members.Ref. No. EN 13836:2006: EEN 13836:2006 (E) 2 Contents Page Foreword .6 1 Scope7 2 Normative references8 3 Terms and definitions .9 3.1 Combustible gases .9 3.2 Constituent parts of the boiler.11 3.2.1 Gas supply .11 3.2.2 Combustion circuit12

12、 3.2.3 Adjusting, control and safety devices 13 3.3 Operation of the boiler16 3.3.1 Gas rates 16 3.3.2 Outputs.17 3.3.4 Gas combustion 17 3.3.5 Times 18 3.3.10 Locking out 19 4 Classification of boilers19 4.1 Gases and categories .19 4.2 Classification according to the mode of evacuation of the comb

13、ustion products20 4.2.1 General .20 4.2.2 Type B.20 4.3 Classification according to operating conditions).21 4.3.1 Standard boiler 21 4.3.2 Low-temperature boiler 21 4.3.3 Gas condensing boiler).21 4.4 Modular boiler21 5 Constructional requirements .21 5.1 General .21 5.2 Conversion to different gas

14、es21 5.3 Materials and method of construction 22 5.3.1 General .22 5.3.2 Materials and thicknesses of walls or tubes under water pressure 22 5.3.3 Thermal insulation 32 5.4 Design.33 5.4.1 General .33 5.4.2 Modular boilers33 5.5 Use and servicing33 5.6 Connections to the gas and water pipes 34 5.6.1

15、 General .34 5.6.2 Connections to the gas pipe 34 5.6.3 Connections to the central heating circuit .34 5.7 Soundness .34 5.7.1 Soundness of the gas circuit .34 5.7.2 Soundness of the combustion circuit.34 5.8 Supply of combustion air and the evacuation of the combustion products 35 5.8.1 Control dam

16、pers in the air or combustion products circuit.35 5.8.2 Fan 35 5.8.3 Air proving .35 5.8.4 Gas/air ratio controls 35 5.8.5 Condensate discharge36 EN 13836:2006 (E) 3 5.9 Checking the state of operation 36 5.10 Drainage. 36 5.11 Electrical equipment. 37 5.12 Operational safety in the event of failure

17、 of the auxiliary energy 37 5.13 Adjusting, control and safety devices 37 5.13.1 General. 37 5.13.2 Adjusters and range rating devices 37 5.13.3 Gas circuit 38 5.13.4 Gas pressure regulator. 39 5.13.5 Ignition devices . 40 5.13.6 Flame supervision systems . 40 5.13.7 Thermostats and water temperatur

18、e limiting devices. 41 5.13.8 Device for monitoring the evacuation of combustion products 42 5.14 Burners 42 5.15 Pressure test points 42 5.16 Chemical composition of the condensate for low-temperature boilers 43 6 Operational requirements 43 6.1 General. 43 6.2 Soundness. 43 6.2.1 Soundness of the

19、gas circuit. 43 6.2.2 Soundness of the combustion circuit and correct evacuation of the combustion products. 43 6.2.3 Soundness of the water circuit 43 6.3 Nominal, maximum and minimum heat inputs, and nominal output. 43 6.3.1 Nominal heat input or maximum and minimum heat inputs 43 6.3.2 Adjustment

20、 of the heat input by the downstream pressure. 44 6.3.3 Minimum ignition rate. 44 6.3.4 Nominal output 44 6.3.5 Gas pressure regulator. 44 6.4 Safety of operation 44 6.4.1 Limiting temperatures 44 6.4.2 lgnition Cross-lighting Flame stability 45 6.4.3 Pre-purge . 46 6.5 Adjusting, control and safety

21、 devices 47 6.5.1 General. 47 6.5.2 Ignition devices . 47 6.5.3 Flame supervision devices 48 6.5.4 Ignition burner and ignition rates 50 6.5.5 Air proving . 50 6.5.6 Gas pressure switches. 51 6.5.7 Control thermostat and safety temperature limiter . 52 6.5.8 Device for monitoring the evacuation of c

22、ombustion products 52 6.5.9 Condensate discharge blockage. 53 6.6 Combustion . 53 6.6.1 Carbon monoxide 53 6.6.2 Other pollutants 53 6.7 Useful efficiencies. 54 6.7.1 Useful efficiency at the nominal heat input 54 6.7.2 Useful efficiency at part load . 54 6.8 Criteria for condensation in the flue .

23、55 6.9 Resistance of materials to pressure . 55 6.9.1 General. 55 6.9.2 Boilers of sheet steel or non-ferrous metals . 55 6.9.3 Boilers of cast iron and cast materials. 55 6.10 Hydraulic resistance. 56 6.11 Combustion air and flue dampers. 56 6.12 Condensation in a standard boiler 56 EN 13836:2006 (

24、E) 4 7 Test methods .56 7.1 General .56 7.1.1 Characteristics of the reference and limit gases .56 7.1.2 General test conditions 62 7.2 Soundness .66 7.2.1 Soundness of the gas circuit .66 7.2.2 Soundness of the combustion circuit and correct evacuation of the combustion products .66 7.2.3 Soundness

25、 of the water circuit66 7.3 Nominal, maximum and minimum heat inputs and nominal output67 7.3.1 The nominal heat input or the maximum and minimum heat inputs .67 7.3.2 Adjustment of the heat input by the downstream pressure .68 7.3.3 Minimum ignition rate.68 7.3.4 Nominal output 68 7.3.5 Gas regulat

26、or .68 7.4 Safety of operation69 7.4.1 Limiting temperatures.69 7.4.2 Ignition Cross-lighting Flame stability.69 7.4.3 Pre-purge71 7.5 Adjusting, control and safety devices 72 7.5.1 General .72 7.5.2 Ignition devices .72 7.5.3 Flame supervision device.73 7.5.4 Ignition burner and ignition rates75 7.

27、5.5 Air proving .75 7.5.6 Gas pressure switches .77 7.5.7 Control thermostat and safety temperature limiter .77 7.5.8 Device for monitoring the evacuation of combustion products 79 7.5.9 Condensate discharge blockage .79 7.6 Combustion80 7.6.1 Carbon monoxide80 7.6.2 Other pollutants.83 7.7 Useful e

28、fficiencies.86 7.7.1 Useful efficiency at the nominal heat input86 7.7.2 Useful efficiency at part load .87 7.8 Criteria for condensation in the flue .92 7.8.1 Determination of flue losses 92 7.8.2 Minimum temperature of the combustion products93 7.9 Resistance of materials to pressure .93 7.9.1 Gen

29、eral .93 7.9.2 Boilers of sheet steel or non-ferrous metals93 7.9.3 Boilers of cast iron and cast materials .93 7.10 Hydraulic resistance .94 7.11 Combustion air and flue dampers .94 7.12 Condensation in a standard boiler 94 8 Marking and instructions95 8.1 Marking of the boiler .95 8.1.1 General .9

30、5 8.1.2 Data plate .95 8.1.3 Supplementary marking .96 8.1.4 Packaging.97 8.1.5 Warnings on the boiler and on the packaging .98 8.1.6 Other information 98 8.2 Instructions98 8.2.1 Technical instructions for the installer .98 8.2.2 Use and maintenance instructions for the user.99 8.2.3 Conversion ins

31、tructions.100 8.3 Presentation.100 Annex A (informative) National situations .112 EN 13836:2006 (E) 5 Annex B (informative) Special national conditions. 118 Annex C (informative) A-deviations 119 Annex D (informative) Practical method of calibrating the test rig to enable the heat loss Dp to be dete

32、rmined. 120 Annex E (informative) Main symbols and abbreviations used within this European Standard . 121 Annex F (informative) Compilations of test conditions used within this European Standard . 122 Annex G (informative) Valving. 125 Annex H (informative) Determination of the heat losses from the

33、test rig of the indirect method and the contributions of the circulating pump of the test rig 128 Annex I (informative) Means of determining the ignition time at full rate 129 Annex J (informative) Example of calculation of the weighting factors for a boiler with several rates 130 Annex K (informati

34、ve) Calculation of conversions of NOx. 132 Annex L (informative) Use of test gases 133 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or provisions of EU Directives . 134 Bibliography . 138 EN 13836:2006 (E) 6 Foreword This European Standard (EN 13836:2006

35、) has been prepared by Technical Committee CEN/TC 109 “Central heating boilers using gaseous fuels”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Februa

36、ry 2007, and conflicting national standards shall be withdrawn at the latest by February 2007. It was established to deal with aspects related to: safety; rational use of energy; fitness for purpose. Other types of boilers are dealt with in separate standards. This European Standard has been prepare

37、d under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directives 90/396/EEC “Approximation of the laws of Member States concerning gas appliances” and 92/42/EEC “Efficiency r

38、equirements for new hot water boilers fired with liquid or gaseous fuels” see informative Annex ZA, which is an integral part of this European Standard. This standard covers only type testing. Boilers within the scope of this European Standard are typically installed in a room separated from living

39、rooms and provided with appropriate ventilation directly to the outside. They need not be fitted with a combustion products discharge safety device but appropriate warnings on the packaging and in the instructions should clearly indicate the limit on the use of this type of boiler. It is impractical

40、 to use the full range of test gases to EN 437 for type testing since their availability, for inputs over 300 kW, may present problems for test houses and manufacturers. Informative Annex L gives guidance on the use of gases for tests in order to ensure conformity with EU Directive 90/396/EEC “Appro

41、ximation of the laws of Member States concerning gas appliances.” According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra

42、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13836:2006 (E) 7 1 Scope This European Standard specifies the requirements and test meth

43、ods concerning, in particular, the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are herea

44、fter referred to as “boilers”. This European Standard applies to boilers of type B, as listed in 4.2: that use one or more combustible gases of the three gas families at the pressures stated in Tables 16 and 17; that have a nominal heat input (on the basis of net calorific value) exceeding 300 kW, b

45、ut not exceeding 1 000 kW, including modular boilers; where the temperature of the heat transfer fluid does not exceed 105 C during normal operation; where the maximum operating pressure in the water circuit does not exceed 6 bar; that can give rise to condensation under certain circumstances; of th

46、e standard and low-temperature types. This European Standard applies to boilers designed for sealed water systems or for open water systems. This European Standard does not contain all the requirements necessary for boilers: intended to be installed in the open or in living rooms; permanently fitted

47、 with more than one flue outlet; where the combustion circuit is sealed with respect to the room where the boiler is installed; of the condensing type; intended to be connected to a common flue having mechanical extraction; fitted with a forced draught burner in accordance with EN 676 (see EN 303-7)

48、; producing hot water for domestic purposes. This standard only covers type testing. Matters related to quality assurance systems, tests during production, and certificates of conformity of auxiliary devices are not dealt with in this European Standard. EN 13836:2006 (E) 8 2 Normative references The

49、 following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 88, Pressure governors for gas appliances for inlet pressures up to 200 mbar EN 125, Flame supervision devices for gas burning appliances Thermo-electric flame supervision devices EN 126, Multifunctional controls for gas burning app