BS EN 13958-2008 Aluminium and aluminium alloys - Cold drawn round coiled tube for general applications - Specification《铝和铝合金 一般用途的冷拉、圆形盘管 规范》.pdf

1、BS EN 13958:2008ICS 77.150.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAluminium andaluminium alloys Cold drawn, round,coiled tube for generalapplications SpecificationThis British Standardwas published under theauthority of the StandardsPolicy and Strateg

2、yCommittee on 31 October2008 BSI 2008ISBN 978 0 580 56397 3Amendments/corrigenda issued since publicationDate CommentsBS EN 13958:2008National forewordThis British Standard is the UK implementation of EN 13958:2008. Itsupersedes BS EN 13958:2003 which is withdrawn.The UK participation in its prepara

3、tion was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correc

4、t application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 13958:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13958October 2008ICS 77.150.10 Supersedes EN 13958:2003 English VersionAluminium and aluminium alloys - Cold drawn, round, coiledtube for ge

5、neral applications - SpecificationAluminium et alliages daluminium - Tubes ronds tirsfournis en couronnes pour applications gnrales -SpcificationsAluminium und Aluminiumlegierungen - GezogeneRundrohre in Ringen fr allgemeine Anwendungen -SpezifikationThis European Standard was approved by CEN on 6 S

6、eptember 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be o

7、btained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Manag

8、ement Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway

9、, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and b

10、y any means reservedworldwide for CEN national Members.Ref. No. EN 13958:2008: EBS EN 13958:2008EN 13958:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Ordering information.5 5 Requirements.6 5.1 Production and manufacturing processes .6 5.2 Qualit

11、y control6 5.3 Chemical composition limits6 5.4 Mechanical properties.6 5.5 Surface quality .6 5.6 Coil characteristics7 5.7 Additional requirements .7 6 Tolerances on dimensions .8 6.1 General8 6.2 Diameter (outside and/or inside)8 6.3 Wall thickness and wall thickness variation (eccentricity) .9 6

12、.4 Length .10 6.5 Squareness of cut ends 11 6.6 Cut end quality.11 7 Tolerances on form11 7.1 General11 7.2 Straightness .11 Annex A (informative) Wall thickness variation (eccentricity)13 A.1 General13 A.2 Specifying round tube sizes and tolerances 13 Bibliography 17 BS EN 13958:2008EN 13958:2008 (

13、E) 3 Foreword This document (EN 13958:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endor

14、sement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyi

15、ng any or all such patent rights. This document supersedes EN 13958:2003. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 5 “Extruded and drawn products“ to revise EN 13958:2003. The following editorial modifications have been introduced during the revision: the

16、contents, text and tables have been changed to bring this European Standard in line with EN 754. The following technical modifications have been introduced during the revision: Clause 1 has been amended to make clear the products covered by this European Standard and those which are not. In addition

17、, the list of the most commonly used general engineering alloys is replaced by a reference to the alloy group only; Clauses 3 and 4 including Tables: the text and the tables are updated; Annex A (informative) has been added to provide further explanation of wall thickness variation (eccentricity) al

18、ong with some examples. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee ref

19、uses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i

20、mplement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerl

21、and and the United Kingdom. BS EN 13958:2008EN 13958:2008 (E) 4 1 Scope This European Standard specifies the tolerances on dimensions and form of round aluminium and aluminium alloys porthole extruded and cold drawn tubes with an outside diameter (OD) of over 2 mm up to and including 50 mm supplied

22、in coil form or in straight lengths cut from coiled material: see Figure 1. This European Standard mainly applies to round cold drawn tube for general engineering applications manufactured in 1xxx series of aluminium and 3xxx series of alloys. The use of this European Standard for non-standardised 1

23、xxx aluminium and 3xxx alloys or alloys from other series, e.g. 5xxx or 6xxx, is subject to agreement between supplier and purchaser. This European Standard only applies to: round tube extruded by the porthole/bridge method in coil form and then cold drawn to the final dimensions required; tube as a

24、bove but delivered in straight lengths cut from coiled material. This European Standard does not apply to: seamless extruded (die/mandrel method) and drawn tubes (EN 754-7); tubes extruded in straight lengths (i.e. not coiled) and drawn (EN 754-8). 2 Normative references The following referenced doc

25、uments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations E

26、N 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 754-2, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 2: Mechanical properties EN 12258-1:1998, Aluminium and aluminium alloys Terms and def

27、initions Part 1: General terms 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 order document document or set of documents agreed between supplier and purchaser at the time of ordering BS EN 13958:2008EN 13958

28、:2008 (E) 5 4 Ordering information The order document shall contain the following: a) form and type of product: form of the product - porthole extruded tube, cold drawn in coil form or straight lengths, reference to EN 573-3 for chemical composition limit, reference to EN 515 for temper designation,

29、 any special requirements identified by the purchaser; b) reference to EN 754-2 for mechanical property limit; c) reference to this document (EN 13958); d) dimensions of the tube: length (where appropriate), and only two of the following dimensions: outside diameter, inside diameter, wall thickness;

30、e) coil characteristics (where appropriate): inner coil diameter (often fixed/standardised), outer coil diameter, width/height of coil, coil weight limitations, drum/bobbin dimensions (where appropriate); f) quantity: mass, number of pieces, total length, tolerance on quantity; g) any requirements f

31、or inspection documents; h) any special requirements agreed between supplier and purchaser: marking of products, e.g. special identification, BS EN 13958:2008EN 13958:2008 (E) 6 references to drawings, part numbers, etc., additional or special testing, surface finish requirements, surface protection

32、, packaging, use of A50mmvalue instead of A value for elongation; i) where special requirements are specified, this shall be stated on the order document with reference to the relevant European Standards. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the ord

33、er document, the production and manufacturing processes shall be left to the discretion of the manufacturer. Unless it is explicitly stated in the order document, no obligation shall be placed on the manufacturer to use the same processes for subsequent similar orders. 5.2 Quality control The suppli

34、er shall be responsible for the performance of all inspection and tests required by the relevant European Standard and/or the particular specification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the supplier at the time

35、 of placing the order. 5.3 Chemical composition limits The chemical composition limits shall be in conformity with the requirements specified in EN 573-3. If the purchaser requires closer limits for elements than those specified in EN 573-3, these limits shall be according to an agreement between su

36、pplier and purchaser and stated in the order document. 5.4 Mechanical properties The mechanical properties shall be in conformity with those specified in EN 754-2 or those agreed between supplier and purchaser and stated in the order document. Typical Brinell hardness (mainly used for flat surfaces,

37、 i.e. basically not suitable for round tubes/non-flat surfaces) values are given in EN 754-2, but they are not binding for acceptance purposes. However, a Brinell hardness value may be agreed upon for acceptance testing. 5.5 Surface quality 5.5.1 Surface quality in general The surface shall be free

38、from defects prejudicial to its suitable and proper use. The reference standards shall be agreed between supplier and purchaser. The product shall have a smooth and clean surface. However, small surface defects such as light scratches, indentations, discolouration and non-uniform surface appearance

39、resulting from the manufacturing process (which cannot always be totally avoided) are generally permitted on the product surface. Such surface quality is commonly referred to as “normal quality”. BS EN 13958:2008EN 13958:2008 (E) 7 A greater degree of tolerance of surface defects (in respect to both

40、 the number and severity) is normally necessary for tube supplied in coil form compared to straight lengths, since it is not possible to remove individual defects within the coil. This issue should be taken into account by the purchaser when placing an order for coiled tube. 5.5.2 Surface defects an

41、d detection In the case of stricter and more specific requirements than “normal quality”, the following shall be subject to agreement between supplier and purchaser and stated in the order document: testing/detection method (e.g. eddy current testing, pressure/leak testing etc.); type (scratches, de

42、nts etc.) and size of defects; method of marking the defects (e.g. ink, paint). 5.5.3 Surface lubrication A surface lubricant may be provided if required to: prevent the occurrence of fretting corrosion during transport; reduce the risk for surface defects created during subsequent manufacturing pro

43、cesses (e.g. decoiling, straightening, cutting, tube manipulation etc.); improve the resistance to surface failures related to surface damage resulting from improper handling and/or storage (e.g. water stains, condensation etc.). As the type and amount of lubrication can have an impact on the follow

44、ing manufacturing process and the final application, the type and amount of lubricant shall be subject to agreement between supplier and purchaser and stated in the order document. 5.6 Coil characteristics 5.6.1 Coil dimensions The following coil dimensions shall be subject to agreement between supp

45、lier and purchaser and stated in the order document: the outside diameter, inside diameter and maximum width/height or weight of the coil; in the case of coils to be supplied on drums/bobbins, the dimensions of the drum/bobbin shall also be specified. 5.6.2 Type of coil winding The type of coil wind

46、ing (random or level winding) can be of importance to the subsequent manufacturing process (e.g. decoiling, straightening etc.) and shall in such cases be subject to agreement between supplier and purchaser and stated in the order document. 5.7 Additional requirements Any additional requirements sha

47、ll be agreed between supplier and purchaser and stated on the order document. BS EN 13958:2008EN 13958:2008 (E) 8 6 Tolerances on dimensions 6.1 General When the outside diameter OD, inside diameter ID, and wall thickness t are all specified, see Figure 1, standard tolerances shall apply to any two

48、of these dimensions, but not to all three. As a result, the purchaser shall state only two nominal dimensions on any given order. Key OD Outside diameter ID Inside diameter t Wall thickness Figure 1 Round tube 6.2 Diameter (outside and/or inside) Mean diameter is defined as the average of two diamet

49、er measurements taken at right angles to each other at any point along the tube length. Ovality is defined as the measured difference between the individual maximum and minimum diameters at any point in the cross section (usually occurs at or about right angles to each other) and at any point along the tube length. The maximum allowable deviations on diameter are given in Table 1. BS EN 13958:2008EN 13958:2008 (E) 9 Table 1 Maximum allowable deviations on diameter (OD and