BS EN 14117-2004 Products and systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products《混凝土结构.pdf

1、BRITISH STANDARD BS EN 14117:2004 Products and systems for the protection and repair of concrete structures Test methods Determination of time of efflux of cementitious injection products The European Standard EN 14117:2004 has the status of a British Standard ICS 91.080.40 BS EN 14117:2004 This Bri

2、tish Standard was published under the authority of the Standards Policy and Strategy Committee on 27 September 2004 BSI 27 September 2004 ISBN 0 580 44497 X National foreword This British Standard is the official English language version of EN 14117:2004. The UK participation in its preparation was

3、entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which

4、 implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publicati

5、on does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/E

6、uropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page,

7、 pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN14117 September2004 ICS91.100.10 Englishversion Productssystemsf

8、ortheprotectionandrepairofconcrete structuresTestmethodsDeterminationoftimeofeffluxof cementitiousinjectionproducts Produitsetsystmespourlaprotectionetlarparationdes structuresenbtonMthodesdessaiDterminationde laviscositdeproduitsdinjectionbasedeciment ProdukteundSystemefrdenSchutzunddie Instandsetz

9、ungvonBetontragwerkenPrfverfahren BestimmungderAusflusszeitvonzementartigen Rissfllstoffen ThisEuropeanStandardwasapprovedbyCENon16April2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutan

10、yalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENm

11、emberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,N

12、orway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCEN

13、nationalMembers. Ref.No.EN14117:2004:EEN 14117:2004 (E) 2 Contents page Foreword3 1 Scope4 2 Normative references4 3 Terms and definitions .4 4 Test principle4 5 Apparatus.4 6 Sampling and preparation5 7 Procedure.5 8 Expression of results5 9 Test report5 EN 14117:2004 (E) 3 Foreword This document (

14、EN 14117:2004) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. It has been drafted by Sub-Committee 8 “Products and systems for the protection and repair of concrete structures“ (Secretariat AFNOR). This European Standard

15、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2005, and conflicting national standards shall be withdrawn at the latest by March 2005. According to the CEN/CENELEC Internal Regulations, the national standards or

16、ganizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,

17、 Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14117:2004 (E) 4 1 Scope This document describes a test method for determining the time of efflux of cementitious injection products, based on the measurement of the time taken for a standard volume of the product to flow through a standar

18、dised cone (Marsh cone). This time of efflux is a measure of the viscosity of cementitious injection products. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated reference

19、s, the latest edition of the referenced document (including any amendments) applies. EN 1504-1:1998, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 1: Definitions. prEN 1504-5:2001, Products and s

20、ystems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 5: Concrete injection. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1504-1:1998 and prEN 1504-5:2001 and the fo

21、llowing apply. 3.1 efflux time time taken by 1000 ml of cementitious injection product to flow through the flow cone 4 Test principle The test measures the time for a specified volume of fluid cementitious injection product to flow through a flow cone. 5 Apparatus 5.1 Flow cone (Marsh cone) made of

22、non corroding material, provided with a semicircular shaped sieve, with dimensions as shown in Figure 1. The discharge tube may be detachable, with a diameter of (4,8 0,1) mm, and a length of (51,0 0,5) mm. It is bolted or screwed to the lower part of the cone, in such a way that no discontinuity oc

23、curs between the cone and the discharge tube. The sieve shall have a mesh size of 2 mm. 5.2 Ring stand, or other device, capable of supporting the flow cone in a vertical, steady position, (150 10) mm above the upper face of the receiving container. 5.3 Receiving container, which allows the measurem

24、ent of a volume of injection product of (1 000 10) ml. 5.4 Level, to assure verticality of the flow cone. EN 14117:2004 (E) 5 5.5 Pouring container, which allows the measurement of a volume of injection product of (1 500 15) ml. 5.6 Stop watch, with an accuracy of 1 s. 5.7 Thermometer, with an accur

25、acy of 0,5 C. 5.8 Mixer, for cementitious injection product. 6 Sampling and preparation The temperature of the dry materials and mixing water shall be such that the temperature of the injection product at the start of mixing is (21 2) C. The injection product shall be mixed in accordance with the ma

26、nufacturer instructions. The time t 0is the time at the end of mixing. If it is required to test the mixture after a longer holding period, continue the mixing of the remaining portion at slow speed for the specified time, taking care to minimize evaporation. 7 Procedure The test shall be carried ou

27、t at a temperature of (21 2) C and a relative humidity of (60 10) %. The flow cone shall be firmly mounted in such a manner that it does not vibrate. The top shall be levelled to ensure verticality. The receiving container shall be levelled. Fill the flow cone with water and, 1 min before introducin

28、g the injection product, drain the water from the cone. Close the outlet of the discharge tube with a stopper. Introduce (1 500 15) ml of injection product into the cone through the sieve. Start the stop watch and simultaneously open the outlet. Stop the watch when (1 000 10) ml of the injection pro

29、duct has flowed through the cone. The measurements shall be repeated three times using a fresh mix each time. Before each measurement, the flow cone and receiving container shall be absolutely clean and free from injection product. If the efflux time has to be determined at time t 0 , the time inter

30、val between “t 0 “ and the beginning of the measurement shall not exceed 1 min. 8 Expression of results The results are expressed as the efflux time in s. 9 Test report The test report shall contain the following information: a) reference to this document; b) name and address of the test laboratory;

31、 EN 14117:2004 (E) 6 c) identification number of the test report; d) name and address of the manufacturer or supplier of the injection product; e) name and identification marks or batch number of the injection product; f) date of supply of the injection product; g) procedure of mixing of the injecti

32、on product (water content, description of mixing equipment, duration of mixing); time interval from completion of mixing at which the test was made; h) date of testing; i) test results : individual and average values, temperature, ambient and of the sample, at the time of test; j) accuracy data; k)

33、date of test report and signature. EN 14117:2004 (E) 7 Dimensions in millimetres Sectional elevation (section A-A) Key 1 Semi circular shaped sieve 2 Bolted flange (optional) Figure 1 Flow cone BS EN 14117:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the ind

34、ependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that t

35、hey possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the

36、 identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, int

37、ernational and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to s

38、upply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Variou

39、s BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive su

40、bstantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be f

41、ound at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyri

42、ght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the s

43、tandard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.