BS EN 14187-2-2017 Cold applied joint sealants Test methods Determination of tack free time《冷用密封胶 试验方法 消粘时间测定》.pdf

1、BS EN 14187-2:2017Cold applied joint sealants Test methodsPart 2: Determination of tack free timeBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 14187-2:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14187-2:2017. It

2、supersedes BS EN 14187-2:2003 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/510/3, Materials for concrete roads.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to i

3、nclude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 87741 4 ICS 91.100.50; 93.080.20 Compliance with a British Standard cannot confer immunity from legal obl

4、igations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 14187-2:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14187-2 March 2017 ICS 93.

5、080.20 Supersedes EN 14187-2:2003English Version Cold applied joint sealants - Test methods - Part 2: Determination of tack free time Mastics pour joints appliqus froid - Mthode dessai - Partie 2 : Dtermination du temps durcissement Kalt verarbeitbare Fugenmassen - Prfverfahren - Teil 2: Bestimmung

6、der klebfreien Zeit This European Standard was approved by CEN on 6 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

7、 bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

8、esponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

9、 Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUR

10、OPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14187-2:2017 EBS EN 14187-2:2017EN 14187-2:2017 (E) 2 Conten

11、ts Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus . 4 6 Conditioning 4 7 Procedure. 4 8 Test report . 5 BS EN 14187-2:2017EN 14187-2:2017 (E) 3 European foreword This document (EN 14187-2:2017) has been prepared by Technical Comm

12、ittee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at

13、 the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14187-2:2003. Apart from editorial changes

14、 no major changes have been made in this revision. This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants Test methods Part 1: Determination of rate of cure. EN 14187-2, Cold applied joint sealants Test methods Part 2: Determination of tack fr

15、ee time. EN 14187-3, Cold applied joint sealants Test methods Part 3: Determination of self-levelling properties. EN 14187-4, Cold applied joint sealants Test methods Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals. EN 14187-5, Cold applied j

16、oint sealants Test methods Part 5: Determination of the resistance to hydrolysis. EN 14187-6, Cold applied joint sealants Test methods Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals. EN 14187-7, Cold applied joint sealants Test methods Pa

17、rt 7: Determination of the resistance to flame. EN 14187-8, Cold applied joint sealants Test methods Part 8: Determination of the resistance to artificial weathering by UV-irradiation. EN 14187-9, Cold applied joint sealants Test methods Part 9: Function testing of joint sealants. According to the C

18、EN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hung

19、ary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14187-2:2017EN 14187-2:2017 (E) 4 1 Scope This European Standard describes a test method fo

20、r determining the tack free time of the cold applied joint sealant for use in joints in roads, air fields and other trafficked areas. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

21、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 6927, Buildings and civil engineering works - Sealants - Vocabulary (ISO 6927) 3 Terms and definitions For the purposes of this document, the t

22、erms and definitions given in EN ISO 6927 apply. 4 Principle The tack free time of a cold applied joint sealant is determined as the time when no sealant is adhering on a peeled off polyethylene film. 5 Apparatus 5.1 Flat bladed mixing spatula. 5.2 Metal or polyethylene frame, measuring internally (

23、125 5) mm long, (38 2) mm wide and (6,0 0,5) mm deep. 5.3 Metal base plate, measuring (150 5) mm long, (75 5) mm wide and (2,0 0,5) mm thick. 5.4 Polyethylene film, measuring (150 5) mm long, (20 2) mm wide and (100 10) m thick. 5.5 A metal plate, measuring (40 1) mm long, (30 1) mm wide and weighin

24、g (30,0 0,5) g. 5.6 Stop watch with a scale-reading precision of at least 1 s. 6 Conditioning Store supplies of the sealant samples in the closed containers for 16 h to 24 h at (23 2) C. 7 Procedure 7.1 For multi-component cold applied joint sealants, thoroughly mix appropriate quantities of base co

25、mponent with curing agent following the manufacturers instruction. One-component sealants can be applied directly from the pack. 7.2 Pour or fill in the cold applied joint sealant into the metal or polyethylene frame (5.2) mounted on its metal base plate (5.3) and strike off level with the flat blad

26、ed mixing spatula. 7.3 Transfer the test specimen into standard conditions at (23 2) C and (50 5) % r. h. and leave it for the tested period of time. BS EN 14187-2:2017EN 14187-2:2017 (E) 5 7.4 At the end of the tested period of time place the polyethylene film (5.4) on the upper surface of the spec

27、imen and immediately cover it with the metal plate (5.5). 7.5 Remove the metal plate after (30 3) s, then peel off the polyethylene film uniformly and constantly at a right angle to the surface of the sealant. 7.6 Examine the polyethylene film for signs of adhesion of the cold applied joint sealant

28、as long as material is picked up. When no material is adhering to the polyethylene film record the tack free time of the cold applied joint sealant. 8 Test report The test report shall include the following information: a) reference to this European Standard; b) name and type of the cold applied joi

29、nt sealant; c) batch of sealant from which the test specimens were produced; d) tack free time of the cold applied joint sealant; e) any deviations from the specified test conditions; f) date of test. This page deliberately left blankThis page deliberately left blankBSI is the national body responsi

30、ble for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together busine

31、ss, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of

32、all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Know

33、ledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Developmen

34、t Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the inter

35、national standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or pub

36、licly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use onl

37、y. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard pu

38、rchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you

39、 can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For fur

40、ther information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch wit

41、h standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of y

42、our standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wi

43、sh. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit

44、 your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20