BS EN 14322-2017 Wood-based panels Melamine faced board for interior uses Definition requirements and classification《木基板材 内部用三聚氰胺面板 定义、要求和分类》.pdf

1、BS EN 14322:2017Wood-based panels Melamine faced board forinterior uses Definition,requirements and classificationBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 14322:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14

2、322:2017.It supersedes BS EN 14322:2004 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/541, Wood based panels.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to incl

3、ude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 87137 5 ICS 79.060.01 Compliance with a British Standard cannot confer immunity from legal obligations.This

4、British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 14322:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14322 March 2017 ICS 79.060.20 Supersedes

5、EN 14322:2004English Version Wood-based panels - Melamine faced board for interior uses - Definition, requirements and classification Panneaux base de bois - Panneaux surfacs mlamins pour usages intrieurs - Dfinition, exigences et classification Holzwerkstoffe - Melaminbeschichtete Platten zur Verwe

6、ndung im Innenbereich - Definition, Anforderungen und Klassifizierung This European Standard was approved by CEN on 9 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stan

7、dard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in a

8、ny other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Rep

9、ublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

10、 EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14322:2017

11、EBS EN 14322:2017EN 14322:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Requirements . 5 5 Appearance 5 5.1 Colour matching 5 5.2 Surface texture . 6 6 Classification by resistance to abrasion 6 7 Verification of compliance . 6 7.1 Ge

12、neral 6 7.2 Factory production control . 6 7.3 External control . 6 8 Marking . 6 Annex A (normative) Supplementary properties . 8 Annex B (normative) Formaldehyde release . 9 Bibliography . 10 BS EN 14322:2017EN 14322:2017 (E) 3 European foreword This document (EN 14322:2017) has been prepared by T

13、echnical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall

14、 be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given

15、to CEN by the European Commission and the European Free Trade Association. This document supersedes EN 14322:2004. Compared to EN 14322:2004 the following modifications have been made: a) extension of the scope to extruded particleboards and sandwich boards for furniture; b) classification by resist

16、ance to abrasion only linked to initial wear point; c) deletion of resistance to cigarette burns in Table A.1;and addition of resistance to axial withdrawal of screws; d) modification in Annex B for formaldehyde release with replacement of EN 717-2 by EN ISO 12460-3. According to the CEN-CENELEC Int

17、ernal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

18、Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14322:2017EN 14322:2017 (E) 4 1 Scope This European Standard specifies the surface requirements and dimen

19、sional tolerances for decorative melamine faced boards for interior use which are common for particleboards, extruded particleboards fibreboards and sandwich boards for furniture. This standard does not apply to boards laminated with so called priming foils or finish foils and laminates according to

20、 EN 438-1. This standard does not apply to laminate floor coverings. Melamine faced wood-based boards in accordance with this standard may be referred to as MFB. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for

21、 its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 311, Wood-based panels Surface soundness Test method EN 320, Particleboards and fibreboards Determination of resistance

22、 to axial withdrawal of screws EN 717-1, Wood-based panels Determination of formaldehyde release Part 1: Formaldehyde emission by the chamber method EN 14323, Wood-based panels Melamine faced boards for interior uses Test methods EN ISO 12460-3, Wood-based panels Determination of formaldehyde releas

23、e Part 3: Gas analysis method (ISO 12460-3) 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 melamine faced board MFB board manufactured by directly applying uncured aminoplastic resin impregnated papers to one or both faces of board substrate

24、s and achieving bonding and curing in the same process using heat and pressure but without the use of an intermediate adhesive Note 1 to entry: The resin of the surface layer is an aminoplastic resin (mainly melamine resin). Note 2 to entry: The board surfaces can be smooth or structured on one or b

25、oth faces and the outer surfaces having decorative colours or design. BS EN 14322:2017EN 14322:2017 (E) 5 4 Requirements Melamine faced boards shall comply with the general requirements as listed in Table 1 when dispatched from the producing factory. Table 1 General requirements at dispatch Requirem

26、ent No Property Test method Unit Thickness range (mm, nominal) 20 1) Tolerances on nominal dimensions thickness”t” relative to nominal value thickness “t” within the board EN 14323 mm 0,3 for class 1 and class 2 according to Table 2. + 0,5/ 0,3 for class 3A, 3B and class 4 according to Table 2 and a

27、ll gloss finishes 0,5 t max t min 0,6 Length and width commercially available size pre-cut panels EN 14323 mm 5 2,5 2) Flatness EN 14323 mm/m 2 (only for balanced surfaces) 3) Edge damage commercially available sizes pre-cut panels EN 14323 mm 10 3 4) Surface defects EN 14323 mm2/m2mm/m2 points 2 le

28、ngth 20 5) Resistance to scratching EN 14323 N 1,5 6) Resistance to staining EN 14323 Rating 3 7) Resistance to cracking EN 14323 Rating 3 8) Formaldehyde release (see Annex B) Class E1 or Class E2 NOTE 1 For the physical and dimensional properties, refer to the relevant standards from the series EN

29、 622, EN 312, EN 14755 or CEN/TS 16526. NOTE 2 Normally, unless otherwise specified, the particleboard grade used will be as required in EN 312 (P2), the MDF grade will be as described in EN 6225 (MDF) and the hardboard grade will be as described in EN 6222 (HB) the extruded particleboards will be a

30、s described in EN 14755. NOTE 3 On request of the customer other values can be specified. NOTE 4 Numerous factors including changes in temperature and relative humidity in storage and fabrication areas at building sites may cause boards and panels to bow or twist irreversibly. 5 Appearance 5.1 Colou

31、r matching Where colour matching is required by the purchaser there shall be only slight deviation (rating 4) between the reference sample and test piece under examination when inspected according to test method given in EN 14323. For mother of pearl and metallic finishes a rating 3 is permitted. BS

32、 EN 14322:2017EN 14322:2017 (E) 6 Since slight variations in colour will occur due to inherent variation in the surfacing papers and the core board, it is recommended that boards or panels to be used side by side should be selected from the same production batch where possible and matched to ensure

33、colour compatibility before fabrication or installation. 5.2 Surface texture Where matching of surface texture is required by purchaser there shall be only slight deviation (rating 4) between the reference sample and test piece under examination when inspected according to test method given in EN 14

34、323. 6 Classification by resistance to abrasion Five classes are defined in the classification system based on the initial wear point (IP) as shown in Table 2. The number of revolutions for each classification is determined according to EN 14323. Table 2 Classification of MFB according to the initia

35、l wear point Class IP Revolutions 1 0,124 mg/m3air or Test method EN ISO 12460-3 Requirement Release 3,5 mg/m2h to 8 mg/m2h Factory production control Test method EN ISO 12460-3 Requirement Release 3,5 mg/m2h to 8 mg/m2h BS EN 14322:2017EN 14322:2017 (E) 10 Bibliography 1 EN 312, Particleboards Spec

36、ifications 2 EN 438-1, High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (usually called laminates) Part 1: Introduction and general information 3 EN 438-2:2016, High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (usually called laminates) Part

37、2: Determination of properties 4 EN 622-1, Fibreboards Specifications Part 1: General requirements 5 EN 622-2, Fibreboards Specifications Part 2: Requirements for hardboards 6 EN 622-5, Fibreboards Specifications Part 5: Requirements for dry process boards (MDF) 7 EN 14755, Extruded particleboards S

38、pecifications 8 CEN/TS 16526, Sandwich boards for furniture (SWB-F) Factory made products Definition, classification and test methods for determination of performance characteristics This page deliberately left blankBSI is the national body responsible for preparing British Standards and other stand

39、ards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and

40、 others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards t

41、o help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and downlo

42、ad PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from ou

43、r Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally l

44、icensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof i

45、n any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device

46、 provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or inte

47、rnal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product

48、(see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to

49、 British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription