BS EN 14593-1-2005 en 8699 Respiratory protective devices - Compressed air line breathing apparatus with demand valve - Apparatus with a full mask - Requirements testing marking《呼吸.pdf

1、BRITISH STANDARD BS EN 14593-1:2005 Respiratory protective devices Compressed air line breathing apparatus with demand valve Part 1: Apparatus with a full mask Requirements, testing, marking The European Standard EN 14593-1:2005 has the status of a British Standard ICS 13.340.30 BS EN 14593-1:2005 T

2、his British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 April 2005 BSI 29 April 2005 ISBN 0 580 45983 7 National foreword This British Standard is the official English language version of EN 14593-1:2005. Together with BS EN 14593-2:2005 and BS EN

3、14594:2005, it supersedes BS EN 139:1995 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PH/4, Respiratory protection, to Subcommittee PH/4/13, Breathing apparatus, which has the responsibility to: A list of organizations represented on this subcommit

4、tee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Se

5、arch” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal

6、obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summ

7、ary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 35 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NO

8、RMEEUROPENNE EUROPISCHENORM EN145931 April2005 ICS13.340.30 S Englishversion RespiratoryprotectivedevicesCompressedairlinebreathing apparatuswithdemandvalvePart1:Apparatuswithafullface maskRequirements,testing,marking AppareilsdeprotectionrespiratoireAppareilsde protectionrespiratoireisolantsadducti

9、ondaircomprim avecsoupapelademandePartie1:Appareilavec masquecompletExigences,essais,marquage AtemschutzgerteDruckluftSchlauchgertemit LungenautomatTeil1:GertemiteinerVollmaske Anforderungen,Prfung,Kennzeichnung ThisEuropeanStandardwasapprovedbyCENon15March2005. CENmembersareboundtocomplywiththeCEN/

10、CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexists

11、inthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Den

12、mark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG Man

13、agementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN145931:2005:EEN 14593-1:2005 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 5 2 Normative references 5 3 Terms, definitions and pictograms6 4 Desc

14、ription .6 5 Requirements.7 5.1 General7 5.2 Ergonomics 7 5.3 Materials .7 5.4 Water immersion7 5.5 Cleaning and disinfecting .7 5.6 Practical performance .8 5.7 Connections .8 5.8 Compressed air line breathing apparatus used with self-contained breathing apparatus - switch over device.9 5.9 Body ha

15、rness or belt .10 5.10 Performance requirements after storage 10 5.11 Flammability.10 5.12 Resistance to pressure .11 5.13 Mobile high pressure air supply systems .11 5.14 Warning devices for mobile high pressure air supply systems .11 5.15 Compressed air supply tube 12 5.16 Breathing hose.13 5.17 L

16、ung governed demand valve13 5.18 Adjustable parts.14 5.19 Full face masks 14 5.20 Inward leakage .14 5.21 Inhalation and exhalation valves14 5.22 Breathing resistance .15 5.23 Carbon dioxide content of inhalation air.15 5.24 Leaktightness.15 6 Testing 16 6.1 General16 6.2 Water immersion17 6.3 Visua

17、l inspection .17 6.4 Practical performance .17 6.5 Strength of connections to facepiece, demand valve, medium pressure connecting tube and breathing hose19 6.6 Resistance to collapse of breathing hose.19 6.7 Strength of compressed air supply tube, body harness and couplings19 6.8 Storage conditionin

18、g.19 6.9 Flammability.20 6.10 Pressure relief valve20 6.11 Resistance to kinking of compressed air supply tube 20 6.12 Resistance to collapse of compressed air supply tube.20 6.13 Heat resistance of compressed air supply tube.21 EN 14593-1:2005 (E) 3 6.14 Inward leakage.21 6.15 Tests for lung-govern

19、ed demand valve 21 6.16 Determination of carbon dioxide content of the inhalation air.22 6.17 Testing of audible warning device.22 6.18 Switch over device 22 7 Marking.22 8 Information supplied by the manufacturer .23 Annex A (normative) Static and dynamic pressure for apparatus with thread connecto

20、r in accordance with EN 148-3 31 Annex B (informative) Marking 33 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC (PPE).34 EN 14593-1:2005 (E) 4 Foreword This European Standard (EN 14593-1:2005) has been prepared by Technic

21、al Committee CEN/TC 79 “Respiratory protective devices”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2005, and conflicting national standards s

22、hall be withdrawn at the latest by October 2005. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/686/EEC. For relationship with EU Directive, see informati

23、ve Annex ZA, which is an integral part of this European Standard. Together with EN 14593-2 and EN 14594, this European Standard supersedes EN 139:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europ

24、ean Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14593-1:200

25、5 (E) 5 Introduction A given respiratory protective device can only be approved when the individual components satisfy the requirements of the test specification, which may be a complete standard or part of a standard, and practical performance tests have been carried out successfully on complete ap

26、paratus where specified in the appropriate standard. If for any reason a complete apparatus is not tested then simulation of the apparatus is permitted provided the respiratory characteristics and weight distribution are similar to those of the complete apparatus. 1 Scope This European Standard spec

27、ifies minimum requirements for compressed air line breathing apparatus with demand valve for use with a full face mask as a respiratory protective device. Escape and diving apparatus and apparatus used in abrasive blasting operations without additional protective features are not covered by this Eur

28、opean Standard, although certain requirements addressing the use in conjunction with escape apparatus and escape conditions are given. Laboratory and practical performance tests are included for the assessment of conformance to the requirements. 2 Normative references The following referenced docume

29、nts are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 132:1998, Respiratory protective devices Definitions of terms and pi

30、ctograms EN 134:1998, Respiratory protective devices Nomenclature of components EN 136:1998, Respiratory protective devices Full face masks Requirements, testing, marking prEN 137:2002, Respiratory protective devices Self-contained open-circuit compressed air breathing apparatus with full face mask

31、Requirements, testing, marking EN 148-1, Respiratory protective devices Threads for facepieces Part 1: Standard thread connection EN 148-2, Respiratory protective devices Threads for facepieces Part 2: Centre thread connection EN 148-3, Respiratory protective devices Threads for facepieces Part 3: T

32、hread connection M45 x 3 EN 402:2003, Respiratory protective devices Lung governed demand self-contained open-circuit compressed air breathing apparatus with full face mask or mouthpiece assembly for escape Requirements, testing, marking EN 12021, Respiratory protective devices Compressed air for br

33、eathing apparatus EN 13274-1:2001, Respiratory protective devices Methods of test Part 1: Determination of inward leakage and total inward leakage EN 13274-2:2001, Respiratory protective devices Methods of test Part 2: Practical performance tests EN 14593-1:2005 (E) 6 EN 13274-3, Respiratory protect

34、ive devices Methods of test Part 3: Determination of breathing resistance EN 13274-4, Respiratory protective devices Methods of test Part 4: Flame tests EN 13274-6, Respiratory protective devices Methods of test Part 6: Determination of carbon dioxide content of the inhalation air EN 50020, Electric

35、al apparatus for potentially explosive atmospheres Intrinsic safety “i“ EN 60079-0, Electrical apparatus for explosive gas atmospheres Part 0: General requirements (IEC 60079-0:2004) EN ISO 8031, Rubber and plastics hoses and hose assemblies Determination of electrical resistance (ISO 8031:1993) 3 T

36、erms, definitions and pictograms For the purposes of this European Standard, the terms, definitions and pictograms given in EN 132:1998, EN 134:1998 and the following apply. 3.1 compressed air line breathing apparatus with a demand valve for use with a full face mask apparatus, which is not self-con

37、tained, in which the wearer is supplied with breathable air from a source of compressed air at a maximum pressure of 10 bar 3.2 facepiece full face mask conforming to EN 136 (Class 2 or Class 3) 3.3 mobile high pressure air supply system supply system that may include a compressor, filters, compress

38、ed air pressure vessels, for use as a mobile source of breathing air 3.4 switch over device device that ensures that in the event of a malfunction or disconnection of the airline, the air supply, when airline is used in conjunction with self contained breathing apparatus, automatically switches over

39、 to the self contained air supply, without interruption of supplied air to the wearer 4 Description This apparatus, with or without positive pressure, enables the wearer to be provided with breathable air, which shall be in accordance with EN 12021, which, on inhalation, flows through a lung governe

40、d demand valve operating at negative pressure (apparatus without positive pressure), or at positive pressure (apparatus with positive pressure) to a suitable facepiece, possibly via a breathing hose. A compressed air supply tube connects the wearer to a supply of compressed air. Exhaled air flows in

41、to the ambient atmosphere via an exhalation valve. NOTE Conformance to EN 12021 can be ensured by a breathable air supply system or an additional device such as a compressed air filter system. EN 14593-1:2005 (E) 7 5 Requirements 5.1 General Unless otherwise specified, the values stated in this Euro

42、pean Standard are expressed as nominal values. Except for temperature limits, values which are not stated as maxima or minima shall be subject to a tolerance of 5 %. Unless otherwise specified, the ambient temperature for testing shall be between 16 C and 32 C and the temperature limits shall be sub

43、ject to an accuracy of 1 C. Where a test clause is referenced, all subclauses of the test clause shall apply, unless otherwise stated. 5.2 Ergonomics The requirements of this European Standard are intended to take account of the interaction between the wearer, the respiratory protective device, and

44、where possible the working environment in which the respiratory protective device is likely to be used. The device shall satisfy 5.3, 5.9 and 5.10. Testing shall be done accordance with 6.4. 5.3 Materials 5.3.1 All materials used in the construction shall have adequate resistance to deterioration by

45、 heat and adequate mechanical strength. Testing shall be done in accordance with 6.3, after any pre-conditioning according to 6.8, and any safety data sheet, if applicable, and declaration of the manufacturer related to materials used in the construction of the device. 5.3.2 Exposed parts, i.e. thos

46、e which may be subjected to impact during use of the apparatus shall not be made of aluminium, magnesium, titanium or their alloys. Testing shall be done in accordance with 6.3. 5.3.3 Materials that may come into direct contact with the wearers skin or that may affect the quality of the breathed air

47、 shall not be known to be likely to cause skin irritation or any other adverse effects to health. Testing shall be done in accordance with 6.3. 5.3.4 The finish of any part of the apparatus likely to be in contact with the wearer shall be free from sharp edges and burrs. Testing shall be done in acc

48、ordance with 6.3 and 6.4. 5.4 Water immersion The apparatus shall continue to function satisfactorily after being submerged temporarily in water. Before immersion and after removal from the water the apparatus shall meet the requirements of 5.22. Testing shall be done in accordance with 6.2. NOTE The apparatus is not designed for use under water. 5.5 Cleaning and disinfecting All materials shall be visibly unimpaired after cleaning and disinfection by the agents and proced