BS EN 15093-2008 Safety of machinery - Safety requirements for hot flat rolling mills《机械安全 热扁钢轧机用安全要求》.pdf

1、BS EN 15093:2008ICS 77.180NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSafety of Machinery Safety requirementsfor hot flat rolling millsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 October2008 BSI 20

2、08ISBN 978 0 580 55204 5Amendments/corrigenda issued since publicationDate CommentsBS EN 15093:2008National forewordThis British Standard is the UK implementation of EN 15093:2008.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/23, Safety of metal producing mills.A li

3、st of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal o

4、bligations.BS EN 15093:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15093October 2008ICS 77.180English VersionSafety of Machinery - Safety requirements for hot flat rolling millsScurit des machines - Prescriptions de scurit relativesaux laminoirs chaud pour produits platsSicherheit von Masc

5、hinen - Sicherheitsanforderungen anWarmflachwalzwerkeThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any al

6、teration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tra

7、nslationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany,

8、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManageme

9、nt Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15093:2008: EBS EN 15093:2008EN 15093:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative References.7 3 Terms a

10、nd definitions .9 4 List of significant hazards 10 5 Safety requirements and/or measures 11 5.1 General requirements for design, planning and risk assessment .11 5.2 List of significant hazards, hazardous situations, safety requirements and/or measures16 5.3 Additional safety requirements or measure

11、s .32 5.4 Noise reduction as a safety requirement 34 6 Verification of the safety requirements and/or measures .35 7 Information for use 36 7.1 General36 7.2 Warning devices and safety signs.36 7.3 Minimum marking 36 7.4 Accompanying documents.36 7.5 Maintenance manual .39 Annex A (normative) Safety

12、 requirements and/or measures for electrical equipment and control systems at hot flat rolling mills41 Annex B (normative) Noise test code .45 Annex C (normative) Protection of persons in case of using asphyxiant gases used in fire fighting systems.49 Annex D (informative) Example for manufacturers

13、safety instructions for maintenance at hot flat rolling mills.53 Annex E (informative) Machines and/or equipment covered by this European Standard.55 Annex F (informative) Examples for the inclusion of safety measures.56 Annex G (informative) Example for the risk analysis due to interfaces 57 Annex

14、ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC .58 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 59 Bibliography 60 BS EN 15093:2008EN 15093:2008 (E) 3

15、 Figures Figure 1 Exemplary layout of a hot flat rolling mill .6 Figure F.1 Looper secured by a locking pin.56 Figure G.1 Diagram of a hypothetical plant indicating potentially hazardous interfaces .57 Tables Table 1 Significant hazards, hazardous situations, safety requirements and/or measures 18 T

16、able 2 Main noise sources of hot flat rolling mills equipment and exemplary noise reduction measures .35 Table A.1 Stop functions43 Table B.1 Example of declared dual-number noise emission values for work stations and specified measuring points .48 BS EN 15093:2008EN 15093:2008 (E) 4 Foreword This d

17、ocument (EN 15093:2008) has been prepared by Technical Committee CEN/TC 322 “Equipment for making and shaping of metals - Safety requirements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text

18、 or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible f

19、or identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA and B

20、, which is an integral part of this document. This European Standard has been elaborated by CEN/TC 322/WG 3, comprising experts from: Denmark, Germany, Italy, Sweden and the United Kingdom. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count

21、ries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

22、n, Sweden, Switzerland and the United Kingdom. BS EN 15093:2008EN 15093:2008 (E) 5 Introduction This European Standard is a type C standard as stated in EN ISO 12100:2003. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope

23、of this European Standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the pr

24、ovisions of this type C standard. Where for clarity an example of a preventative measure is given in the text, this should not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved. This European

25、 Standard assumes that the equipment is operated and maintained by trained personnel. BS EN 15093:2008EN 15093:2008 (E) 6 1 Scope This European Standard defines the general safety requirements for hot rolling mills for flat products as defined in 3.1. This European Standard deals with significant ha

26、zards, hazardous situations and events relevant to hot rolling mills for flat products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see Clauses 4 and

27、 5). This European standard applies to: Machinery and equipment used for the manufacturing of metal hot rolled flat products from the material supply from (1), via the mill stands (2), to the exit (5) (see Figure 1). Key 4 coiler/cooling bed 1 e. g., continuous casting machine (according to EN 14753

28、) or furnace (according to EN 746-1) 5 coil or plate transport 2 mill stands 6 roll changing device 3 roller tables 7 border of the hot rolling mill Figure 1 Exemplary layout of a hot flat rolling mill The following equipment is outside the scope of this standard: furnaces in accordance with EN 746-

29、1, EN 746-2 and EN 746-3; continuous casting machines according to EN 14753; hook conveyors according to EN 619; roll shop equipment; storage equipment (e. g., high-bay warehouses); cranes, fork lifts, trucks and railway trucks and other vehicles. This European standard is not applicable to hot roll

30、ing mills for flat products, manufactured before the date of publication of this standard by CEN. BS EN 15093:2008EN 15093:2008 (E) 7 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies

31、. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 614-1:2006, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles

32、EN 614-2, Safety of machinery Ergonomic design principles Part 2: Interactions between the design of machinery and work tasks EN 626-1, Safety of machinery Reduction of risks to health from hazardous substances emitted by machinery Part 1: Principles and specifications for machinery manufacturers EN

33、 842, Safety of machinery Visual danger signals - General requirements, design and testing EN 894-1, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actuators EN 894-2, Safety of

34、machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators EN 953, Safety of machinery Guards - General requirements for the desig

35、n and construction of fixed and movable guards EN 981, Safety of machinery System of auditory and visual danger and information signals EN 982, Safety of machinery Safety requirements for fluid power systems and their components - Hydraulics EN 983, Safety of machinery Safety requirements for fluid

36、power systems and their components - Pneumatics EN 999, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts of the human body EN 1037:1995, Safety of machinery Prevention of unexpected start-up EN 1063, Glass in building Security glazing Testing and cla

37、ssification of resistance against bullet attack EN 1088, Safety of machinery Interlocking devices associated with guards - Principles for design and selection EN 1299, Mechanical vibration and shock Vibration isolation of machines Information for the application of source isolation EN 1837, Safety o

38、f machinery Integral lighting of machines EN 12094-1, Fixed firefighting systems Components for gas extinguishing systems Part 1: Requirements and test methods for electrical automatic control and delay devices EN 12198-3, Safety of machinery Assessment and reduction of risks arising from radiation

39、emitted by machinery Part 3: Reduction of radiation by attenuation or screening EN 12254, Screens for laser working places Safety requirements and testing EN 12464-1, Light and lighting Lighting of work places Part 1: Indoor work places BS EN 15093:2008EN 15093:2008 (E) 8 EN 13478, Safety of machine

40、ry Fire prevention and protection EN 13861, Safety of machinery Guidance for the application of ergonomics standards in the design of machinery EN 14253, Mechanical vibration Measurement and calculation of occupational exposure to whole-body vibration with reference to health Practical guidance EN 1

41、5004-1, Fixed firefighting systems Gas extinguishing systems Part 1: Design, installation and maintenance (ISO 14520-1:2006, modified) EN 50171, Central power supply systems EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified

42、) EN 60447, Basic and safety principles for man-machine interface Marking and identification Actuating principles (IEC 60447:2004) EN 60529, Degrees of protection provided by enclosures (IP code) EN 60825-1, Safety of laser products Part 1: Equipment classification and requirements (IEC 60825- 1:200

43、7) EN 60825-4, Safety of laser products Part 4: Laser guards (IEC 60825-4:2006) EN 61310-1, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, auditory and tactile signals (IEC 61310-1:2007) EN 61310-2; Safety of machinery Indication, marking and actuation Part 2:

44、 Requirements for marking (IEC 61310-2:2007) EN 61496-1, Safety of machinery Electro-sensitive protective equipment Part 1: General requirements and tests (IEC 61496-1:2004, modified) EN ISO 4871:1996, Acoustics Declaration and verification of noise emission values of machinery and equipment (ISO 48

45、71:1996) EN ISO 7731, Ergonomics Danger signals for public and work areas Auditory danger signals (ISO 7731:2003) EN ISO 11064-1, Ergonomic design of control centres Part 1: Principles for the design of control centres (ISO 11064-1:2000) EN ISO 11202, Acoustics Noise emitted by machinery and equipme

46、nt Measurement of emission sound pressure levels at a work station and at other specified positions - Survey method in situ (ISO 11202:1995) EN ISO 11688-1, Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning (ISO/TR 11688-1:1995) EN ISO 12100-1:2003,

47、Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13732-1, Ergonomics of the thermal

48、 environment Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfaces (ISO 13732-1:2006) EN ISO 13849-1:2006, Safety of machinery Safety-related parts of control systems Part 1: General principles for design (ISO 13849-1:2006) BS EN 15093:2008EN 15093:2008 (E) 9 EN

49、 ISO 13850:2006, Safety of machinery Emergency stop Principles for design (ISO 13850:2006) EN ISO 13857, Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) EN ISO 14121-1:2007, Safety of machinery Risk assessment Part 1: Principles (ISO 14121-1:2007) EN ISO 14122-1, Safety of machinery Permanent means of access to machinery Part 1: Choic