BS EN 15336-2007 Adhesives - Determination of the time to rupture of bonded joints under static load《粘合剂 静负荷状态下胶粘件断裂时间的测定》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58bonded joints under static loadThe European Standard EN 15336:2007 has the status of a British Stan

2、dardICS 83.180Adhesives Determination of the time to rupture of BRITISH STANDARDBS EN 15336:2007BS EN 15336:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 580 50421 1Amendments issued since publicationAmd

3、. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 15336:2007.The UK participation in its prepar

4、ation was entrusted to Technical Committee PRI/52, Adhesives.A list of organizations represented on PRI/52 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15336February 2007IC

5、S 83.180English VersionAdhesives - Determination of the time to rupture of bonded jointsunder static load ( ISO 15109:1998 modified)Adhsifs - Dtermination du temps jusqu la rupture dejoints colls soumis une charge statique (ISO 15109:1998modifie)Klebstoffe - Bestimmung der Zeit bis zum Bruch geklebt

6、erFgeverbindungen unter statischer Belastung (ISO15109:1998 modifiziert)This European Standard was approved by CEN on 29 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national st

7、andard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other

8、 language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin

9、land,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMIT

10、EE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15336:2007: EEN 15336:2007 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references 5 3 Principle5 4 Appar

11、atus .5 5 Specimens 5 5.1 Adherend material .5 5.2 Shape and dimensions5 5.3 Cleaning and surface treatment of adherends .6 5.4 Preparation of specimens.6 5.5 Conditioning and testing atmosphere.6 5.6 Number of specimens .6 6 Procedure .6 7 Expression of results 7 8 Precision.7 9 Test report 7 EN 15

12、336:2007 (E) 3 Foreword This document (EN 15336:2007) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

13、the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

14、 Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15336:2007 (E) 4 Safety statement

15、 Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to

16、ensure compliance with any regulatory conditions. EN 15336:2007 (E) 5 1 Scope This European Standard describes a procedure for the determination of the time to failure of a bonded joint, using a specimen which is statically loaded under specified conditions. This method can only be used for comparin

17、g adhesives, and the results cannot be used for design purposes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

18、nt (including any amendments) applies. EN 1465, Adhesives Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies (ISO 4587:1979 modified) EN 13887, Structural adhesives Guidelines for surface preparation of metals and plastics prior to adhesive bonding EN ISO 291, Plastics S

19、tandard atmospheres for conditioning and testing (ISO 291:2005) EN ISO 10365, Adhesives Designation of main failure patterns (ISO 10365:1992) 3 Principle The time to rupture of a bonded lap-shear specimen is measured under a specific load. 4 Apparatus 4.1 Test rig, capable of holding specimens secur

20、ely at one end, in the vertical position, the other end of each specimen being linked to a fixture capable of receiving different weights in order to vary the load. The direction of the load shall coincide with the longitudinal axis of the specimen. The rig shall be capable of loading several specim

21、ens simultaneously. It shall be designed such that any vibration associated with breakage of one specimen will not influence the remaining specimens. The rig shall be placed in an environmentally controlled cabinet or be designed such that the specimens are tested under controlled conditions. 4.2 Ti

22、mer, capable of measuring the time to failure of a specimen to an accuracy of 1 %. 5 Specimens 5.1 Adherend material The adherends shall be made of metal, rigid plastic or rigid fibre-reinforced plastic. 5.2 Shape and dimensions Specimens shall be as shown in Figure 1. The thickness of the adherends

23、 shall be sufficient to avoid significant plastic deformation. EN 15336:2007 (E) 6 Dimensions in millimetres Key 1 Bonded zone 2 Gripped zone 3 Spacer plate Figure 1 Test specimen for all adherend materials 5.3 Cleaning and surface treatment of adherends The cleaning and surface treatment of adheren

24、ds shall be in accordance with the instructions of the adherend manufacturer and/or adhesive manufacturer, and/or shall be chosen from the methods described in EN 13887. 5.4 Preparation of specimens Prepare specimens in accordance with the procedure described in EN 1465. Apply and cure the adhesive

25、in accordance with the manufacturers recommendations. Control the bond line thickness by appropriate means, such as glass spheres or wire spacers. When using glass spheres, the content shall not exceed 0,5 % of the mass of the adhesive. When using wire spacers, prepare the specimens in such a way th

26、at the final test piece does not include the area containing the wire. The bond line thickness shall be reported in the test report. 5.5 Conditioning and testing atmosphere Condition and test the specimens in one of the standard atmospheres specified in EN ISO 291. 5.6 Number of specimens Prepare an

27、d test at least three specimens for each stress investigated. 6 Procedure Attach the specimens to the test rig. Allow them to reach equilibrium in the controlled conditions selected for the test. Using weights, carefully apply the loads necessary to obtain the required stresses. EN 15336:2007 (E) 7

28、NOTE It is usual to investigate stresses which are a percentage of the tensile lap-shear strength determined in accordance with EN 1465. Record the time to failure of each specimen. Determine the failure pattern for each specimen, in accordance with EN ISO 10365. 7 Expression of results Record graph

29、ically the stress investigated versus the average time to failure, plotting the stress as the ordinate and the time to failure as the abscissa on a logarithmic scale. 8 Precision The precision of this test method is not known because interlaboratory data are not available. When interlaboratory data

30、are obtained, a precision statement will be added at the following revision. 9 Test report The test report shall include the following information: a) reference to this European Standard; b) all details necessary for identification of the adhesive tested, including type, source and manufacturers cod

31、e number; c) all details necessary for complete identification of the adherends used, including their dimensions and the method of preparing the surfaces prior to bonding; d) bond line thickness; e) atmosphere used for conditioning and testing; f) number of specimens tested; g) graph of stress versu

32、s time to failure; h) failure pattern for each specimen; i) date of the test. BS EN BSI389 Chiswick High RoadLondonW4 4AL15336:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at

33、the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and servi

34、ces. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers memb

35、ers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20

36、 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on st

37、andardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Informati

38、on Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. T

39、el: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI

40、 publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electro

41、nic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.