BS EN 15387-2011 Packaging Flexible laminate tubes Test methods to assess the strength of the side seam《包装 挠性层压管 评估侧缝强度的试验方法》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15387:2011Packaging Flexible laminatetubes Test methods to assessthe strength of the side seamBS EN 15387:2011 BRITISH STANDARDNational forewordThis British Standard is the

2、 UK implementation of EN 15387:2011.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, Packaging - Plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the neces

3、saryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 56324 9ICS 55.120Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committe

4、e on 31 August 2011.Amendments issued since publicationDate Text affectedBS EN 15387:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15387 August 2011 ICS 55.120 English Version Packaging - Flexible laminate tubes - Test methods to assess the strength of the side seam Emballage - Tubes soup

5、les lamins - Mthodes dessai pour dterminer la rsistence de la soudure longitudinale Packmittel - Laminattuben - Prfverfahren zur Bestimmung der Festigkeit der Lngsnaht This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations

6、 which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. Thi

7、s European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN memb

8、ers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

9、 Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Memb

10、ers. Ref. No. EN 15387:2011: EBS EN 15387:2011EN 15387:2011 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Principle . 4 3 Test equipment for burst test 4 4 Test operation . 5 4.1 Burst test. 5 4.2 Overlap test 6 5 Test report . 7 BS EN 15387:2011EN 15387:2011 (E) 3 Foreword This document (EN 15387:

11、2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting nat

12、ional standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CE

13、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Li

14、thuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15387:2011EN 15387:2011 (E) 4 1 Scope This European Standard specifies methods for the assessment of the strength of the side seam of flexible lami

15、nate tubes. It is applicable to flexible laminate tubes used for packing pharmaceutical, cosmetic, hygiene, food and other household products. 2 Principle The burst test and the overlap test serve to assess the strength of the side seam. These tests are complementary. The burst test is used to measu

16、re whether the tube can withstand a defined air pressure. In addition the overlap test gives information about possible reasons for an insufficient strength of the overlap of the laminate at the side seam. 3 Test equipment for burst test 3.1 Compressed air system. Air compressor with an initial mini

17、mum pressure of 2 bar equipped with an air regulator allowing a constant and stable pressure. BS EN 15387:2011EN 15387:2011 (E) 5 3.2 Test device. Key 1 Valve 2 Pressure gauge 3 Tube 4 Clamp 5 Adaptor for thread 6 Protective box 7 Compressed air Figure 1 Burst test principle 4 Test operation 4.1 Bur

18、st test a) Place the tube in the clamp (side seam centred), close one end of the tube and introduce the air from the other end of the tube. b) For tubes with a diameter less than or equal to 40 mm apply a pressure of 2 bar for 10 s. For tubes with a diameter larger than 40 mm apply a pressure of 1,8

19、 bar for 10 s. BS EN 15387:2011EN 15387:2011 (E) 6 c) The tube shall not burst in the overlap area or the side seam during the 10 s that the pressure is applied. If the tube bursts in any other area than the side seam or the overlap or if the tube does not burst at all, it meets the specifications.

20、d) Below 250 m laminate thickness the test shall be subject to a mutual agreement between customer and supplier. 4.2 Overlap test a) An appropriate measure shall be taken to make the inner layer visible. If the inner layer is not visible, samples shall be prepared by using an appropriate contrasting

21、 agent. b) Cut a cross-section of the tube approximately 10 mm from its open end. 1) If the tube is an ethylene vinyl alcohol (EVOH) barrier laminate, stain the section with a contrasting agent (e.g. iodine solution of 2,5 grams iodine, 2,5 grams potassium iodide, 15 grams distilled water, 80 grams

22、ethanol). This will turn an EVOH barrier layer dark brown or black within approximately one minute and enable it to be seen easily under the magnifying device. 2) If the tube is an aluminium barrier laminate, no additional sample preparation is required. 3) Other plastic or metal laminates will requ

23、ire careful examination to allow correct measurement of the overlap. c) Under the magnifying device the side seam will show an overlap of aluminium or a black line with polymer flow around the weld. d) Take the reading in mm from the graticule. e) The overlap shall be equal to or larger than 1 mm. f

24、) The overlap test does not apply to laminate tubes where the tube wall is joined edge to edge. Key 1 external layer 2 adhesive 3 barrier 4 inner layer 5 overlap Figure 2 Tested side seam BS EN 15387:2011EN 15387:2011 (E) 7 If laminate structures without an aluminium or EVOH barrier are used, a suit

25、able test procedure should be mutually agreed upon between customer and supplier. 5 Test report If not otherwise agreed between supplier and customer the test report shall contain the following information: a) reference to this European Standard and if necessary a specification for the method of sam

26、pling and acceptance of the batch; b) the complete identification of the batch and of the tubes checked; c) the number of tubes checked; d) the number of defects; e) the test result; f) all factors which could have affected the results or all operating details not specified in this European Standard

27、; g) date, place of test and name of tester. This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in E

28、urope and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of Bri

29、tish Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of th

30、e technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44

31、 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel

32、: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information

33、on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Em

34、ail: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding

35、 online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as per

36、mitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course

37、 of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: