BS EN 15421-2007 Packaging - Flexible aluminium tubes - Determination of the adhesion of the internal and external protective lacquering《包装 软铝管 内部和外部防护清漆粘附力的测定》.pdf

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58a

2、dhesion of the internal and external protective lacqueringICS 55.120Packaging Flexible aluminium tubes Determination of the BRITISH STANDARDBS EN 15421:2007BS EN 15421:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIThis British Standard was pub

3、lished under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 56210 5Amendments/corrigenda issued since publicationDate CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standa

4、rd is the UK implementation of EN 15421:2007.The UK participation in its preparation was entrusted to Technical Committee PKW/0, Packaging.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary

5、provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15421November 2007ICS 55.120English VersionPackaging - Flexible aluminium tubes - Determination of theadhesion of the internal and external protective lacqueringEmballage - T

6、ubes souples en aluminium - Dterminationde ladhrence des vernis de protection intrieure etextrieurePackmittel - Aluminiumtuben - Bestimmung derHaftfestigkeit des Innen- und AuenschutzlackesThis European Standard was approved by CEN on 7 October 2007.CEN members are bound to comply with the CEN/CENEL

7、EC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CE

8、N member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN mem

9、bers are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, S

10、witzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No.

11、EN 15421:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E) 2 Contents Page Foreword. 3 1 Scope . 4 2 Principle. 4 3 Apparatus 4 4 Test conditions . 6 5 Procedure 6 6 Test report. 6 Bibliography . 7 Licensed Copy: Wang Bin, ISO

12、/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E) 3 Foreword This document (EN 15421:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national

13、 standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. C

14、EN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech R

15、epublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STAN

16、DARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E) 4 1 Scope This standard specifies a method for the determination of the adhesion of the internal and external protective lacquer of aluminium tubes. It is applicable to aluminium tubes that are coated with an internal or external p

17、rotective lacquer and which are used for packing, e.g. pharmaceutical, cosmetic, hygiene, food and other household products. 2 Principle By means of a compressing device the tube is compressed to a defined extent and under defined temperature conditions to create a standardized and sharp-edged defor

18、mation of the tube. The kinks are checked visually for any cracks and/ or delamination of internal or external lacquer. 3 Apparatus Compressing device according to Figure 1 (example). Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E)

19、 5 Key 1 Compressing clamp 2 Guide pin (for tubes diameter 19 mm = 8 mm, for tubes diameter 19 mm = 15 mm) 3 Guide bolt 4 Base plate 5 Tube Figure 1 Test device Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E) 6 4 Test conditions Th

20、e tests are carried out at a temperature between (23 5) C. For testing the adhesive strength of inner and outer protective lacquers of products stored or used under cold conditions, (5 + 3) C, the samples have to be stored under the same conditions for at least 2 h prior to testing. The test has to

21、be done immediately after taking the samples out of the refrigerator. 5 Procedure Insert the tube in the compressing device. In order to keep the tube straight during compression an internal guide pin should be used. Compress the tube until the tube body is reduced to (15 5) % of the original tube b

22、ody length. Remove the crushed tube from the compressing device and stretch it again in the axial direction. Check the stretched tubes for cracked and detached lacquer parts of the inner and outer protective lacquering. If there are any cracks or detached lacquer parts, the samples have failed. 6 Te

23、st report The test report shall contain the following information: a) Reference to this standard and if necessary a specification for the method of sampling and acceptance of the batch. b) Complete identification of the batch and of the tubes checked. c) Description and the dimensions of the samples

24、. d) Nature of the internal and external protective lacquering. e) Test temperature. f) Number of samples checked. g) Number and description of defects. h) If necessary, acceptance or refusal of the batch depending on the specifications. i) All factors which could have affected the results or all op

25、erating details not specified in this standard. j) Date, place of test and name of tester. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIEN 15421:2007 (E) 7 Bibliography 1 EN 12374, Packaging - Flexible tubes - Terminology 2 EN 13046, Packaging -

26、Flexible cylindrical metallic tubes - Dimensions and tolerances 3 EN 13047, Packaging - Flexible conical metallic tubes - Dimensions and tolerances Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin, ISO/EXCHANGE CHINA

27、STANDARDS, 14/05/2008 02:13, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondonW4 4AL15421:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is i

28、ncorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if any

29、one finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating servi

30、ce called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. S

31、tandards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range

32、 of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7

33、111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +4

34、4 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds th

35、e copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or

36、otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.