1、BS EN 15566:2016Railway applications Railway rolling stock Drawgear and screw couplingBSI Standards PublicationBS EN 15566:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 15566:2016. It supersedes BS EN 15566:2009+A1:2010 which is withdrawn.The UK committee
2、 draws users attention to the distinction between normative and informative elements, as defined in Clause 3 of the CEN/CENELEC Internal Regulations, Part 3.Normative: Requirements conveying criteria to be fulfilled if compliance with the document is to be claimed and from which no deviation is perm
3、itted.Informative: Information intended to assist the understanding or use of the document. Informative annexes do not contain requirements, except as optional requirements, and are not mandatory. For example, a test method may contain requirements, but there is no need to comply with these requirem
4、ents to claim compliance with the standard.The UK loading gauge is much smaller than the gauge in Europe and the maximum axle load is higher at 25.4 tonnes. As a consequence of this, longer thinner wagons are built to maximize the pay load of wagons carrying lower density products. In order to maxim
5、ize the volumetric capacity of the wagon body within this overall length 520 mm buffers continue to be used with a head radius of 1 250 mm to cater for the tighter curves found in many UK terminals (for example Oleo OP176GX buffers). As EN 15566 is referenced in the Wagon TSI, any new wagons would h
6、ave to be built with a 620 mm buffer and 2 750 mm head radius. This would have three effects:1) The wagon bodies would have to be shorter to allow for the longer buffers within the same 18 300 mm overall length with a corresponding loss of payload of typically 1 tonne on every journey. 2) The use of
7、 the 2 750 mm head radius would push the drawbar loads over the 250 kN limit when negotiating 70 m curves, which would necessitate lengthening the screw couplings every time the wagons went into tight terminals and tightening them again once they were back on the mainline. This would cause delays to
8、 arrivals and departures, add cost and present an additional safety hazard to the shunters.3) If the 520 mm buffer is no longer used for new build wagons, the manufacturers will eventually cease to make them. The vast majority of UK bogie wagons are fitted with these buffers and any new casings requ
9、ired to replace worn ones would then need to be specially made at a vast increase in cost. Therefore wagons for use exclusively in the UK may continue to use 520 mm projection buffers in EN 15551 and the corresponding UK Draw Hook (to drawing C1-A1-9006711) and Screw Coupling (to drawing F-AO-13970)
10、. Drawings may be obtained from Serco Raildata email: The UK participation in its preparation was entrusted by Technical Committee RAE/3, Railway Applications - Rolling Stock Products, to Subcommittee RAE/3/-/7, Railway applications - Couplers.A list of organizations represented on this subcommittee
11、 can be obtained on request to its secretary.BS EN 15566:2016BRITISH STANDARDThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN
12、 978 0 580 74356 6ICS 45.040; 45.060.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate Text af
13、fectedThis page deliberately left blankBS EN 15566:2016g3g3g3g8g24g21g18g19g8g4g17g3g22g23g4g17g7g4g21g7g3g17g18g21g16g8g3g8g24g21g18g19g50g8g17g17g8g3g8g24g21g18g19g34g12g22g6g11g8g3g17g18g21g16g3EN 15566 g3 g3g3 g22g135g146g150g135g143g132g135g148g3g884g882g883g888g3g12g6g22g3g886g887g484g882g888g
14、882g484g882g883g3 g22g151g146g135g148g149g135g134g135g149g3g8g17g3g883g887g887g888g888g483g884g882g882g891g938g4g883g483g884g882g883g882g8g144g137g142g139g149g138g3g25g135g148g149g139g145g144g3g3g21g131g139g142g153g131g155g3g131g146g146g142g139g133g131g150g139g145g144g149g3g486g3g21g131g139g142g153g
15、131g155g3g148g145g142g142g139g144g137g3g149g150g145g133g141g3g486g3g7g148g131g153g3g137g135g131g148g3g131g144g134g3g149g133g148g135g153g3g133g145g151g146g142g139g144g137g3g4g146g146g142g139g133g131g150g139g145g144g149g3g136g135g148g148g145g152g139g131g139g148g135g149g3g486g3g16g131g150g177g148g139g1
16、35g142g3g148g145g151g142g131g144g150g3g136g135g148g148g145g152g139g131g139g148g135g3g486g3g18g148g137g131g144g135g149g3g134g135g3g150g148g131g133g150g139g145g144g3g135g150g3g150g135g144g134g135g151g148g3g134g821g131g150g150g135g142g131g137g135g3g3 g5g131g138g144g131g144g153g135g144g134g151g144g137g1
17、35g144g3g486g3g22g133g138g139g135g144g135g144g136g131g138g148g156g135g151g137g135g3g486g3g29g151g137g135g139g144g148g139g133g138g150g151g144g137g3g151g144g134g3g22g133g138g148g131g151g132g135g144g141g151g146g146g142g151g144g137g3g23g138g139g149g3g8g151g148g145g146g135g131g144g3g22g150g131g144g134g13
18、1g148g134g3g153g131g149g3g131g146g146g148g145g152g135g134g3g132g155g3g6g8g17g3g145g144g3g890g3g13g151g142g155g3g884g882g883g888g484g3g3g3g6g8g17g3g143g135g143g132g135g148g149g3g131g148g135g3g132g145g151g144g134g3g150g145g3g133g145g143g146g142g155g3g153g139g150g138g3g150g138g135g3g6g8g17g512g6g8g17g8
19、g15g8g6g3g12g144g150g135g148g144g131g142g3g21g135g137g151g142g131g150g139g145g144g149g3g153g138g139g133g138g3g149g150g139g146g151g142g131g150g135g3g150g138g135g3g133g145g144g134g139g150g139g145g144g149g3g136g145g148g3g137g139g152g139g144g137g3g150g138g139g149g3g8g151g148g145g146g135g131g144g3g22g150
20、g131g144g134g131g148g134g3g150g138g135g3g149g150g131g150g151g149g3g145g136g3g131g3g144g131g150g139g145g144g131g142g3g149g150g131g144g134g131g148g134g3g153g139g150g138g145g151g150g3g131g144g155g3g131g142g150g135g148g131g150g139g145g144g484g3g24g146g486g150g145g486g134g131g150g135g3g142g139g149g150g14
21、9g3g131g144g134g3g132g139g132g142g139g145g137g148g131g146g138g139g133g131g142g3g148g135g136g135g148g135g144g133g135g149g3g133g145g144g133g135g148g144g139g144g137g3g149g151g133g138g3g144g131g150g139g145g144g131g142g3g149g150g131g144g134g131g148g134g149g3g143g131g155g3g132g135g3g145g132g150g131g139g14
22、4g135g134g3g145g144g3g131g146g146g142g139g133g131g150g139g145g144g3g150g145g3g150g138g135g3g6g8g17g486g6g8g17g8g15g8g6g3g16g131g144g131g137g135g143g135g144g150g3g6g135g144g150g148g135g3g145g148g3g150g145g3g131g144g155g3g6g8g17g3g143g135g143g132g135g148g484g3g3g23g138g139g149g3g8g151g148g145g146g135g
23、131g144g3g22g150g131g144g134g131g148g134g3g135g154g139g149g150g149g3g139g144g3g150g138g148g135g135g3g145g136g136g139g133g139g131g142g3g152g135g148g149g139g145g144g149g3g523g8g144g137g142g139g149g138g481g3g9g148g135g144g133g138g481g3g10g135g148g143g131g144g524g484g3g4g3g152g135g148g149g139g145g144g3g
24、139g144g3g131g144g155g3g145g150g138g135g148g3g142g131g144g137g151g131g137g135g3g143g131g134g135g3g132g155g3g150g148g131g144g149g142g131g150g139g145g144g3g151g144g134g135g148g3g150g138g135g3g148g135g149g146g145g144g149g139g132g139g142g139g150g155g3g145g136g3g131g3g6g8g17g3g143g135g143g132g135g148g3g1
25、39g144g150g145g3g139g150g149g3g145g153g144g3g142g131g144g137g151g131g137g135g3g131g144g134g3g144g145g150g139g136g139g135g134g3g150g145g3g150g138g135g3g6g8g17g486g6g8g17g8g15g8g6g3g16g131g144g131g137g135g143g135g144g150g3g6g135g144g150g148g135g3g138g131g149g3g150g138g135g3g149g131g143g135g3g149g150g1
26、31g150g151g149g3g131g149g3g150g138g135g3g145g136g136g139g133g139g131g142g3g152g135g148g149g139g145g144g149g484g3g3g6g8g17g3g143g135g143g132g135g148g149g3g131g148g135g3g150g138g135g3g144g131g150g139g145g144g131g142g3g149g150g131g144g134g131g148g134g149g3g132g145g134g139g135g149g3g145g136g3g4g151g149g
27、150g148g139g131g481g3g5g135g142g137g139g151g143g481g3g5g151g142g137g131g148g139g131g481g3g6g148g145g131g150g139g131g481g3g6g155g146g148g151g149g481g3g6g156g135g133g138g3g21g135g146g151g132g142g139g133g481g3g7g135g144g143g131g148g141g481g3g8g149g150g145g144g139g131g481g3g9g139g144g142g131g144g134g481
28、g3g9g145g148g143g135g148g3g28g151g137g145g149g142g131g152g3g21g135g146g151g132g142g139g133g3g145g136g3g16g131g133g135g134g145g144g139g131g481g3g9g148g131g144g133g135g481g3g10g135g148g143g131g144g155g481g3g10g148g135g135g133g135g481g3g11g151g144g137g131g148g155g481g3g12g133g135g142g131g144g134g481g3g
29、12g148g135g142g131g144g134g481g3g12g150g131g142g155g481g3g15g131g150g152g139g131g481g3g15g139g150g138g151g131g144g139g131g481g3g15g151g154g135g143g132g145g151g148g137g481g3g16g131g142g150g131g481g3g17g135g150g138g135g148g142g131g144g134g149g481g3g17g145g148g153g131g155g481g3g19g145g142g131g144g134g4
30、81g3g19g145g148g150g151g137g131g142g481g3g21g145g143g131g144g139g131g481g3g22g142g145g152g131g141g139g131g481g3g22g142g145g152g135g144g139g131g481g3g22g146g131g139g144g481g3g22g153g135g134g135g144g481g3g22g153g139g150g156g135g148g142g131g144g134g481g3g23g151g148g141g135g155g3g131g144g134g3g24g144g13
31、9g150g135g134g3g14g139g144g137g134g145g143g484g3g3g3g3g3g8g24g21g18g19g8g4g17g3g6g18g16g16g12g23g23g8g8g3g9g18g21g3g22g23g4g17g7g4g21g7g12g29g4g23g12g18g17g3g6g18g16g12g23g50g3g8g24g21g18g19g50g8g17g3g7g8g3g17g18g21g16g4g15g12g22g4g23g12g18g17g3g8g24g21g18g19g34g12g22g6g11g8g22g3g14g18g16g12g23g8g8g
32、3g9g111g21g3g17g18g21g16g24g17g10g3g3g3g3CEN-CENELECg3Management Centre: Avenue Marnix 17, B-1000 Brussels g825g3g884g882g883g888g3g6g8g17g3 g4g142g142g3g148g139g137g138g150g149g3g145g136g3g135g154g146g142g145g139g150g131g150g139g145g144g3g139g144g3g131g144g155g3g136g145g148g143g3g131g144g134g3g132g
33、155g3g131g144g155g3g143g135g131g144g149g3g148g135g149g135g148g152g135g134g3g153g145g148g142g134g153g139g134g135g3g136g145g148g3g6g8g17g3g144g131g150g139g145g144g131g142g3g16g135g143g132g135g148g149g484g3g21g135g136g484g3g17g145g484g3g8g17g3g883g887g887g888g888g483g884g882g883g888g3g8BS EN 15566:2016
34、EN 15566:2016 (E) 2 Contents Page European foreword . 7 Introduction 9 1 Scope . 10 2 Normative references . 10 3 Terms and definitions 11 4 Requirements for all types of draw gear and screw coupling 13 4.1 Classification and designation . 13 4.2 Interaction coupling/buffer . 13 4.3 Interface dimens
35、ion for freight wagons. 14 4.4 Life time . 15 5 Draw gear 16 5.1 Draw gear components 16 5.2 Draw hook and drawbar Requirements . 18 6 Screw coupling 18 6.1 General requirements 18 6.2 Screw coupling Requirements 20 7 Elastic device . 20 7.1 Characteristics of elastic device 20 7.2 Elastic device Re
36、quirements . 21 Annex A (normative) Dynamic test (fatigue test) procedure 22 A.1 Background 22 A.2 Performance of the test 22 A.2.1 Conditioning . 22 A.2.2 Dynamic test (fatigue test) 22 A.2.3 Non-destructive tests 24 A.2.4 Determination of residual strength . 24 A.2.5 Macrographic and Micrographic
37、tests 24 A.3 Criteria of acceptance . 24 Annex B (normative) Draw hook dimensions 25 Annex C (normative) Draw gear Interface dimension 26 Annex D (normative) Screw coupling components dimensions . 27 Annex E (normative) Draw hook and drawbar Requirements 29 E.1 Physical characteristics . 29 E.1.1 Ap
38、pearance . 29 E.1.2 Integrity . 29 BS EN 15566:2016EN 15566:2016 (E) 3 E.1.3 Material examination 29 E.2 Geometrical characteristics 30 E.3 Mechanical characteristics 30 E.3.1 Tensile test on test piece 30 E.3.2 Resilience. 30 E.3.3 Hardness 30 E.3.4 Tensile test on draw hook and draw bar . 30 E.3.5
39、 Compressive test on draw hook for locomotives 31 E.4 Marking 31 E.5 Manufacture 31 E.5.1 General on draw bars 31 E.5.2 General on draw hooks . 31 E.5.3 Machining 31 E.5.4 Heat treatment 31 E.5.5 Rectification of defects 32 E.6 Acceptance 32 E.6.1 General . 32 E.6.2 Inspection of the draw hooks . 32
40、 E.6.3 Inspection of draw bars 37 E.6.4 Conclusion of the inspections . 38 E.7 Delivery 38 E.7.1 Protection against oxidation 38 E.7.2 Packaging . 38 Annex F (normative) Screw coupling and component parts Requirements . 39 F.1 Material 39 F.2 Physical characteristics 39 F.2.1 Appearance . 39 F.2.2 S
41、oundness 39 F.2.3 Additional requirements for screw couplings . 40 F.3 Geometrical characteristics 40 F.3.1 General . 40 F.3.2 Dimensions limited either by two unmachined or rough-machined surfaces or by one unmachined or rough-machined surface 40 F.3.3 Dimensions limited by two machined surfaces .
42、41 F.4 Mechanical characteristics 41 F.4.1 Heat treatment 41 F.4.2 Hardness 41 BS EN 15566:2016EN 15566:2016 (E) 4 F.4.3 Values for predetermined breaking loads for the weakest part. 41 F.4.4 Resilience 42 F.4.5 Requirements for screw coupling 42 F.4.6 Requirement for handle and trunnion . 43 F.5 Ma
43、rking 44 F.6 Manufacture . 44 F.6.1 Preparation of the materials 44 F.6.2 Manufacture of the component parts . 44 F.7 Acceptance 46 F.7.1 General . 46 F.7.2 Inspection of the manufacture 46 F.8 Inspection of the materials, component parts and screw couplings . 46 F.8.1 Materials submission for accep
44、tance 46 F.8.2 Grouping into batches 47 F.8.3 Nature and proportion of the tests 47 F.8.4 Sampling and preparation of the samples and test pieces 48 F.8.5 Carrying out of the checks and tests 52 F.9 Completion of inspections. 53 F.10 Delivery 54 F.10.1 Protection against oxidation 54 F.10.2 Packing
45、. 54 Annex G (normative) Elastic device Requirements . 55 G.1 Rubber elastomer or other elastomer elastic device 55 G.1.1 General . 55 G.1.2 Metal inserts requirements 55 G.1.3 Elastomer requirements . 55 G.1.4 Static test . 57 G.1.5 Endurance test 58 G.1.6 Bonding 59 G.1.7 Inspection and Tests . 59
46、 G.1.8 Markings 60 G.2 Friction spring/Ring spring 61 G.2.1 Manufacturers marks 61 G.2.2 Flexibility test 61 G.2.3 Endurance test 62 Annex H (normative) Marking 63 BS EN 15566:2016EN 15566:2016 (E) 5 H.1 General . 63 H.2 Marking of the screw coupling . 63 H.3 Draw gear 64 H.4 Draw bar 64 H.5 Summary
47、 of markings . 65 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2008/57/EC 66 Bibliography . 68 Figures Figure 1 Force-stroke diagram for stored and absorbed energy . 12 Figure 2 g22g151g146g146g145g148g150g3g146g142g131g150g135g3g5
48、18g3g12g144g150g135g148face dimension for freight wagons 15 Figure 3 g7g148g131g153g3g137g135g131g148g3g518g3g4g149g149g135g143g132g142g155 . 17 Figure 4 Standard screw coupling with non-loosening hinged ball handle . 19 Figure 5 Standard screw coupling with hinged handle with non-loosening upper re
49、st 20 Figure A.1 Example of Load cycles Step 1 and Step 2 23 Figure B.1 Draw hook . 25 Figure C.1 Drawbar with “fork” and safety device . 26 Figure C.2 Joint pin 26 Figure D.1 Coupling hook pin 27 Figure D.4 Shackle . 28 Figure E.1 Location of the test samples . 34 Figure E.2 Marking of the draw hook for the tensile test 35 Figure E.3 Location of the test samples . 37 Figure F.1 Location of the measurement of the deformation of the screw coupling . 42 Figure F.2 Test facility for the tensile test of the screw couplin
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1