BS EN 15636-2010 Sanitary appliances - Shower trays made from impact modified extruded acrylic sheets - Requirements and test methods《卫生用具 改良型挤压成型聚丙烯薄板材制淋浴盆 试验方法和要求》.pdf

1、BS EN 15636:2010ICS 91.140.70NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSanitary appliances Shower trays madefrom impact modifiedextruded acrylic sheets Requirements andtest methodsThis British Standardwas published under theauthority of the StandardsPolicy

2、 and StrategyCommittee on 31 March2010 BSI 2010ISBN 978 0 580 65900 3Amendments/corrigenda issued since publicationDate CommentsBS EN 15636:2010National forewordThis British Standard is the UK implementation of EN 15636:2010.The UK participation in its preparation was entrusted to TechnicalCommittee

3、 B/503, Sanitary appliances.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard ca

4、nnot confer immunityfrom legal obligations.BS EN 15636:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15636 March 2010 ICS 91.140.70 English Version Sanitary appliances - Shower trays made from impact modified extruded acrylic sheets - Requirements and test methods Appareils sanitaires - R

5、eceveurs de douche en feuilles dacrylique extrudes modifies choc - Prescriptions et mthodes dessai Sanitrausstattungsgegenstnde - Duschwannen, hergestellt aus schlagzh-modifizierten extrudierten Acrylplatten - Anforderungen und Prfverfahren This European Standard was approved by CEN on 14 February 2

6、010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

7、 on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management

8、 Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

9、 Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any

10、form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15636:2010: EBS EN 15636:2010EN 15636:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Requirements .44.1 General 44.2 Material .44.3 Surface appearance .44.4 Waste outlet ho

11、le .44.5 Overflow hole .54.6 Hole edges 54.7 Dimensional deviations .54.8 Geometric deviations 54.8.1 General 54.8.2 Squaring .54.8.3 Straightness of the rim sides .54.8.4 Straightness of the bottom edge of the rim 54.8.5 Flatness of the top surface of rim 54.9 Bottom of the shower tray 54.10 Resist

12、ance to temperature changes 64.11 Resistance to impact .64.12 Permitted deflections 64.13 Rim 65 Marking .6Annex A (normative) Shower tray test methods 7A.1 Sequence of tests 7A.2 Geometric deviations 7A.2.1 Test apparatus .7A.2.2 Squaring .7A.2.3 Straightness of the rim side .8A.2.4 Straightness of

13、 the bottom edge of the rim 9A.2.5 Flatness of the top surface of the rim. 10A.3 Resistance to temperature change . 11A.3.1 Test apparatus 11A.3.2 Procedure 11A.4 Resistance to impact 12A.4.1 Test apparatus 12A.4.2 Procedure 12A.5 Determination of deflections . 12A.5.1 General . 12A.5.2 Test apparat

14、us 12A.5.3 Preloading . 13A.5.4 Deflection test 1 Deflection of the rim and the bottom due to a load on the bottom . 13A.5.5 Deflection test 2 Deflection of the rim due to a load on the rim on the side of entry . 14Bibliography . 17BS EN 15636:2010EN 15636:2010 (E) 3 Foreword This document (EN 15636

15、:2010) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and confl

16、icting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Accordin

17、g to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

18、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15636:2010EN 15636:2010 (E) 4 1 Scope This European Standard specifies the requirements for shower trays for domestic purposes made from

19、 impact modified extruded acrylic sheet conforming with EN 13558 with the aim of ensuring that the product, when installed in accordance with the manufacturers instructions, will provide satisfactory performance in use. This standard is applicable to all sizes and shapes of shower trays. 2 Normative

20、 references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 251, Shower trays Connecting dimen

21、sions EN 13558, Specifications for impact modified extruded acrylic sheets for shower trays for domestic purposes 3 Terms and definitions For the purposes of this document the following terms and definitions apply. 3.1 domestic purposes use in homes, hotels, accommodation for students, hospitals and

22、 similar buildings, except when special medical provisions are required 4 Requirements 4.1 General The manufacturer shall provide instructions for installation and care with each shower tray. The shower tray shall be free from sharp edges that would be exposed after the installation of the shower tr

23、ay in accordance with the manufacturers instructions. 4.2 Material The shower tray shall be manufactured from impact modified extruded acrylic sheet complying with EN 13558. 4.3 Surface appearance When the shower tray is visually inspected under strong and oblique illumination there shall be no evid

24、ence of cracks, chips, or other surface defects, such as unexpected changes in colours, etc., that will impair the appearance or performance of the shower tray. 4.4 Waste outlet hole The shower tray shall have at least one outlet hole. The dimensions of the waste outlet hole and the clearance around

25、 the waste outlet hole shall either be in accordance with the requirements of EN 251 or the manufacturer shall supply or recommend a suitable waste outlet fitting. BS EN 15636:2010EN 15636:2010 (E) 5 4.5 Overflow hole When the shower tray is provided with an overflow hole the dimensions of the overf

26、low hole and the clearance around the overflow hole shall either be in accordance with the requirements of EN 251 or the manufacturer shall supply or recommend a suitable overflow fitting. 4.6 Hole edges The edges of any holes in the shower tray shall not show evidence of chips, cracks, or any other

27、 defects that may impair the appearance or performance of the shower tray. 4.7 Dimensional deviations The dimensions of shower trays shall not deviate from the size quoted by the manufacturer by greater than 5 mm. If the manufacturer states two sizes (e.g. both a work size and a nominal size) they s

28、hall state to which size the permitted deviations apply. For round shower trays, length and width correspond to the diameter. 4.8 Geometric deviations 4.8.1 General The straight sides or edges of the shower tray that might abut independent surroundings or supporting structures shall comply with the

29、requirements of 4.8.2 to 4.8.4 and all shower trays shall comply with 4.8.5. NOTE These requirements are not applicable to sides or edges that are purposedly designed as curves or slopes. 4.8.2 Squaring When tested in accordance with A.2.2 the deviation from square, q, shall be less than or equal to

30、 5 mm. 4.8.3 Straightness of the rim sides When tested in accordance with A.2.3 the deviation from straightness of the rim sides, s, shall be less than or equal to 5 mm. 4.8.4 Straightness of the bottom edge of the rim When tested in accordance with A.2.4 the deviation from straightness of the botto

31、m edge of the rim, r, shall be less than or equal to 5 mm. 4.8.5 Flatness of the top surface of rim When tested in accordance with A.2.5 the deviation from flatness of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.9 Bottom of the shower tray When the shower tray is installed

32、in accordance with the manufacturers instructions and the waste outlet hole is open, all water shall empty from the shower tray unless prevented by surface tension. BS EN 15636:2010EN 15636:2010 (E) 6 4.10 Resistance to temperature changes When tested in accordance with A.3 the shower tray shall sho

33、w no evidence of distortion or other defects which will impair the appearance or functioning of the shower tray and any deflection shall be less than or equal to 4 mm. 4.11 Resistance to impact When tested in accordance with A.4 the bottom and the rim of the shower tray shall show no evidence of dis

34、tortion or other defects that impair the appearance or functioning of the shower tray. 4.12 Permitted deflections When tested in accordance with A.5 the deflections shall be less than or equal to the values given in Table 1. Table 1 Permitted deflections Test method Deflection under load a mm Residu

35、al deflection amm A.5.4 2 0,3A.5.5 4 0,3 a Values in addition to any deflection of the test rig (see A.5.2). 4.13 Rim When a shower tray is installed in accordance with the manufacturers instructions, the rim shall not encourage water to drain away from the inside of the shower tray. Roll top rims a

36、nd rims incorporating special features are not subject to this requirement. 5 Marking Every shower tray shall be legibly marked on the underside with the following information: a) reference to this European Standard (EN 15636); b) name or trademark of the manufacturer or supplier. BS EN 15636:2010EN

37、 15636:2010 (E) 7 Annex A (normative) Shower tray test methods A.1 Sequence of tests The tests shall be carried out on one shower tray of each type in sequence A.2 A.3 A.5 A.4. A.2 Geometric deviations A.2.1 Test apparatus a) Length measuring device with an accuracy of 0,5 mm. b) Reference plane sur

38、face with flatness tolerance of 0,5 mm. c) Fixed square, fixed to the reference plane surface, at least 25 mm deeper than the depth of the rim side to be measured, one arm at least 300 mm longer than the length to be measured and the other arm at least as long as the width to be measured. d) Movable

39、 square, at least 25 mm deeper than the depth of the rim side to be measured, one side at least 300 mm long and the other side at least as long as the width to be measured. e) Thickness comparator or gauge with an accuracy of 0,1 mm. f) Spacing rollers made of metallic material, at least 25 mm deepe

40、r than the depth of the rim side to be measured and with a diameter Dsrwith a tolerance of 0,25 mm. g) Thickness wedge with a thickness of 501,0mm. A.2.2 Squaring Place the shower tray upside down on the reference plane surface as shown in Figure A.4. Position sides AB and AD adjacent to the fixed s

41、quare and place three spacing rollers with diameter Dsreach at a distance of r + 15 mm from the corners A and B, as shown in Figure A.1, where r is the radius of the corners. Measure the distance x as shown in Figure A.1 and calculate q as the difference Dsr x. Position the movable square along the

42、side BC and place a fourth spacing roller at a distance of r + 15 mm from the corner B. Measure the distance y as shown in Figure A.1 and calculate q as the difference Dsr y. Turn the shower tray through 180 and check the distances x and y at corners A and B respectively. Record the deviation. BS EN

43、 15636:2010EN 15636:2010 (E) 8 Dimensions in millimetres 1324BCADr +15 r +15Dr+15ryxr+15srKey 1 spacing rollers 2 fixed square 3 movable square 4 shower tray r radius of the corner Dsrdiameter of spacing roller x distance between the rim and the fixed square y distance between the rim and the movabl

44、e square Figure A.1 Squaring A.2.3 Straightness of the rim side Place the shower tray upside down on the reference plane surface as shown in Figure A.4. Position two spacing rollers with diameter Dsrbetween the rim side of the shower tray and one side of the fixed square, each at a distance of r + 1

45、5 mm from the corners, as shown in Figure A.2, where r is the radius of the corners of the shower tray. Measure the maximum and minimum distances amax and amin between the rim side and the fixed square using the thickness comparator or gauge. Calculate the deviation s as the difference amax amin. Re

46、cord the deviation. Repeat the procedure for each rim of the shower tray. BS EN 15636:2010EN 15636:2010 (E) 9 Dimensions in millimetres 2BCADr +15 r +15D3a1srrKey 1 fixed square 2 spacing rollers 3 shower tray a distance between rim side and fixed square r radius of the corner Dsrdiameter of spacing

47、 roller Figure A.2 Straightness of the rim side A.2.4 Straightness of the bottom edge of the rim Place the shower tray upside down on the reference plane surface as shown in Figure A.3. Position the shower tray against the fixed square as shown in Figure A.3. Measure the maximum and minimum distance

48、s bmax and bmin between the bottom edge of the rims and the top surface of the fixed square using the thickness comparator or gauge. Calculate the deviation r as the difference bmax bmin. Record the total deviation. BS EN 15636:2010EN 15636:2010 (E) 10 1234bKey 1 thickness comparator or gauge 2 fixe

49、d square 3 shower tray 4 reference plane b distance between the bottom edge of the rim and top surface of the fixed square Figure A.3 Straightness of the bottom edge of the rim A.2.5 Flatness of the top surface of the rim Place the shower tray upside down on the reference plane surface as shown in Figure A.4. Check, using the thickness wedge, the deviation