BS EN 15820-2011 Polymer modified bituminous thick coatings for waterproofing Determination of watertightness《防水用聚合物改性沥青厚涂层 防渗水测定》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15820:2011Polymer modifiedbituminous thick coatingsfor waterproofing Determination ofwatertightnessBS EN 15820:2011 BRITISH STANDARDNational forewordThis British Standard i

2、s the UK implementation of EN 15820:2011. The UK participation in its preparation was entrusted to TechnicalCommittee B/546, Flexible sheets for waterproofing and water vapour control.A list of organizations represented on this committee can be obtained on request to its secretary.This publication d

3、oes not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 62271 7 ICS 91.100.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the autho

4、rity of the Standards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 15820:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15820 March 2011 ICS 91.100.50 English Version Polymer modified bituminous thick coatings for waterp

5、roofing - Determination of watertightness Revtements bitumineux pais modifis aux polymres pour impermabilisation - Dtermination de ltanchit leau Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Bestimmung der Wasserdichtheit This European Standard was approved by CEN on 13 F

6、ebruary 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be

7、 obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to t

8、he CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

9、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All right

10、s of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15820:2011: EBS EN 15820:2011EN 15820:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Principle 45 Apparatus .56 Test specimens 66.1 General 66.2 Pr

11、eparation .66.3 Conditioning of test specimens .66.4 Dimensions of the test specimens.67 Procedure .77.1 Test conditions 77.2 Procedure .78 Expression of results and precision 78.1 Expression of results 78.2 Precision .79 Test report 7BS EN 15820:2011EN 15820:2011 (E) 3 Foreword This document (EN 15

12、820:2011) has been prepared by Technical Committee CEN/TC 361 “Project Committee Polymer modified bituminous thick coatings for waterproofing Definitions/requirements and test methods”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard,

13、either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

14、CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cypru

15、s, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15820:2011EN 15820:2011 (E) 4 1 Scop

16、e This European Standard specifies a procedure for determining the watertightness of polymer modified bituminous thick coatings for waterproofing (i.e. the resistance to hydraulic pressure). 2 Normative references The following referenced documents are indispensable for the application of this docum

17、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. FprEN 15814:2011, Polymer modified bituminous thick coatings for waterproofing Definitions and requirements ISO 554, Standard atmospher

18、es for conditioning and/or testing Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in FprEN 15814:2011 apply. 3.1 watertightness the coating can be deemed watertight if the side of the specimen that is not exposed to water does not exhibit an

19、y leakage of water 4 Principle Test procedure for polymer modified bituminous thick coatings intended for use in pressure application, e.g. pressured water in soil. Submission of a test specimen to a specified water pressure for at least 24 h against a disk containing four slots of specified form an

20、d dimensions. The test specimen is observed to establish whether it remains watertight. BS EN 15820:2011EN 15820:2011 (E) 5 5 Apparatus The apparatus consists of a device (see Figures 1 and 2) by which a pressure can be applied to one side of a test specimen. Key 1 slots 2 cover 3 test specimen 4 hy

21、drostatic pressure 5 observation gap 6 slotted plate Figure 1 Slot pressure testing device for watertightness at high pressures Figure 2 Device for the slot pressure test: sketch of the cover The test specimen is covered by a circular disk containing four slots. The form and dimensions of the slots

22、are specified by the requirements indicated in Figure 3. BS EN 15820:2011EN 15820:2011 (E) 6 Dimensions in millimetres Key aall edges of the slotted plate are rounded to a radius of 0,5 mm approximately Figure 3 Slotted plate 6 Test specimens 6.1 General 3 circular test specimen with a diameter equa

23、l to the extend diameter of the slotted plate (approximately 130 mm). 6.2 Preparation Production of a membrane from the polymer modified bituminous thick coatings in accordance with classes defined in FprEN 15814:2011, Table 1. In case reinforcement is used the first layer is placed on a release lay

24、er with approximately half the thickness of the bitumen layer. Subsequently the reinforcement is incorporated and finally the second layer of bitumen is applied. The wet layer has to be that thick, that after drying process the designated dry layer thickness will be achieved. To provide the designat

25、ed dry layer thickness the wet coating has to be levelled off with the help of a frame or gauge of accordant height. 6.3 Conditioning of test specimens The test specimens shall be stored for at least 28 days at a normal climate of (23 2) C and a relative humidity of (50 5) % in accordance with ISO 5

26、54 prior to testing. 6.4 Dimensions of the test specimens The thickness of the dry layer shall be measured using vernier callipers permitting a reading to 0,1 mm. 12 readings shall be taken. The highest and lowest values shall be ignored and the mean value calculated from the remaining 10 values. BS

27、 EN 15820:2011EN 15820:2011 (E) 7 7 Procedure 7.1 Test conditions The test shall be carried out at (23 2) C. The test pressure shall be specified in the product specification. It shall be ensured that the margins are watertight. 7.2 Procedure Fill the apparatus in accordance with Figure 1 with water

28、 until overflowing. Place the test specimen with its upper side downwards in the apparatus and cover with the specified slotted plate. Place the cover and progressively tighten until the specimen is tightly in place. Pressurise progressively to the specified test pressure. Once the test pressure is

29、reached, maintain the pressure for a period according to the product specific but minimum 24 h. Observe the watertightness of the test specimen after the testing time (sudden pressure drop or presence of water on the non exposed face of the test specimen). 8 Expression of results and precision 8.1 E

30、xpression of results The watertightness test is considered passed if all test specimens remain watertight on the side subjected to the test pressure after the specified testing time. 8.2 Precision Precision data are currently not available. 9 Test report The test report shall include at least the fo

31、llowing information: a) all details necessary to identify the product tested; b) a reference to this European Standard (i.e. EN 15820) and any deviation from it; c) details of preparation of test specimens in accordance with Clause 6; d) test procedure including: test pressure; test period; specimen

32、 thickness; deviation of test conditions; BS EN 15820:2011EN 15820:2011 (E) 8 e) the test results in accordance with Clause 8; f) the dates of the tests. This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publi

33、cations, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax

34、+44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or

35、 ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat

36、 subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and

37、 foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise

38、 requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all it

39、s products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel

40、: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of

41、the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior wr

42、itten permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: