BS EN 181102-1995 Specification for harmonized system of quality assessment for electronic components - Blank detail specification fibre optic branching devices - Type wavelength s.pdf

1、BRITISH STANDARD BS EN 181102:1995 Specification for Harmonized system of quality assessment for electronic components Blank detail specification Fibre optic branching devices Type: wavelength selective transmissive star The European Standard EN 181102:1994 has the status of a British StandardBSEN18

2、1102:1995 BSI 04-2000 ISBN 0 580 35831 3 Committees responsible for this British Standard The United Kingdom participation in the preparation of this European Standard was entrusted to Technical Committee EPL/86, Fibre Optics, upon which the following bodies were represented: BEAMA Electrical Cable

3、and Conductor Accessory Manufacturers Association British Approvals Service for Cables British Cable Makers Confederation British Telecommunications plc Department of Trade and Industry (National Physical Laboratory) ERA Technology Ltd. Federation of the Electronics Industry Fibre optic Industry Fed

4、eration Ministry of Defence National Supervising Inspectorate (BSI QA) Optical Sensors Collaborative Association Society of Cable Television Engineers Amendments issued since publication Amd. No. Date CommentsBSEN181102:1995 BSI 04-2000 i Contents Page Committees responsible Inside front cover Natio

5、nal foreword ii Foreword 2 Text of EN 181102 3BSEN181102:1995 ii BSI 04-2000 National foreword This British Standard has been prepared under the direction of the Electrotechnical Sector Board, and is the English language version of EN181102:1994 Blank detail specification: Fibre optic branching devi

6、ces Type: wavelength selective transmissive star, published by the European Committee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). This standard lists details, measurements, performance, test and inspection requirements which shall be included as mandatory r

7、equirements in any detail specification for this type of fibre optic branching device. Detail specifications shall conform to the requirements of this blank detail specification and BS CECC 00111 Rule of Procedure11. Specifications Part4:1991 Regulations for CECC detail specifications. The British S

8、tandard which implements the CECC Rules of Procedure is BS9000 General requirements for a system for electronic components of assessed quality Part 2:1991 Specification for the national implementation of the CECC system. A British Standard does not purport to include all the necessary provisions of

9、a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred to Corresponding British Standard EN 181000:1994 BS EN 181000:1994 Harmonized syste

10、m of quality assessment for electronic components. Generic specification: Fibre optic branching devices Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 12 and a back cover. This standard has been updated (see copyright date)

11、 and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 181102 July 1994 UDC Descriptors: Quality, electronic components, fibre optic branching devices English version Blank Detail Specifi

12、cation: Fibre Optic Branching Devices Type: Wavelength Selective Transmissive Star Spcification particulire cadre: Coupleurs fibres optiques Type: Slectif en longueur donde, transmission en toile Vordruck fr Bauartspezifikation: Faseroptische Verzweiger Bauart: Wellenlngenselektiver Sternbertrager T

13、his European Standard was approved by the CENELEC Electronic Components Committee (CECC) on 17 January 1993. CENELEC members are bound to comply with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any altera

14、tion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the General Secretariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language

15、 made by translation under the responsibility of a CENELEC member into its own language and notified to the CECC General Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Gree

16、ce, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and UnitedKingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnic

17、al Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to CENELEC members Ref. No. EN 181102:1994 EEN181102:1994 BSI 04-2000 2 Foreword The CENELEC Electronic

18、 Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the

19、 harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate, of Conformity. The components produced under the System are thereby acceptable in all member countries without further testing. Th

20、is specification was prepared by CECC WG 27. The text of the draft based on document CECC(Secretariat)3016 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3275, it was approved by CECC as EN181102 on17January1993. The following dates were fi

21、xed: Contents Page Foreword 2 1 Introduction 3 2 Qualification approval 3 3 Quality conformance inspection 3 4 Preparation of Detail Specifications (DS) 3 Table 1 Fixed sample qualification approval test schedule 7 Table 2 Lot-by-lot inspection test schedule (Groups A and B) 7 Table 3 Periodic inspe

22、ction test schedule (Groups C and D) 8 Table 4 Details, measurements and performance requirements 9 latest date of announcement of the EN at national level (doa) 1993-09-14 latest date of publication of an identical national standard (dop) 1994-03-14 latest date of declaration of national standards

23、obsolescence 1994-03-14 latest date of withdrawal of conflicting national standards (dow) 2003-09-14EN181102:1994 BSI 04-2000 3 1 Introduction This specification is a BDS for Fibre Optic Branching Devices of the “Wavelength selective transmissive star” type. This includes instructions for preparing

24、a DS. 2 Qualification approval 2.1 Procedure The DS shall state the qualification approval procedure to be used in accordance with clause3.3 of EN181000. 2.2 Test schedule and performance requirements The test schedule for qualification by the fixed sample procedure shall be given inTable 1 of DS (s

25、eeclauses2.2, 4.5 and4.6 of EN181000). 3 Quality conformance inspection 3.1 Lot-by-lot inspection The test schedule for lot-by-lot inspection (groupsA and B) shall be given inTable 2 of the DS (seeclauses2.2, 4.5 and4.6 of EN 181000). 3.2 Periodic inspection The test schedule for periodic inspection

26、 (groups C and D) shall be given inTable 3 of the DS (seeclauses2.2, 4.5 and4.6 of EN181000). 4 Preparation of Detail Specifications (DS) Each BDS is published separately as a proforma document, with numbered spaces provided for entering the information necessary to create a DS. If the spaces provid

27、ed are too small, then the information shall be provided on additional sheets forming part of the completed DS. Instructions for filling in the numbered spaces in a BDS are given below: 1) The name of the ONH under whose authority the DS is published and, if applicable, the organization from whom th

28、e DS is available. 2) The CECC symbol and the number allotted to the DS by the CECC General Secretariat. 3) The number and issue number of the CECC GS; also the national reference(s) if different. 4) If different from the CECC number, the national number of the DS, date of issue and any further info

29、rmation required by the national system, together with any amendment numbers. 5) A brief description of the component or range of components. 6) The level of quality assessment (A, B, C or X), sampling procedure (fixed quantity or lot-by-lot) and the climatic category. For 5) and 6) the text to be g

30、iven in the DS shall be suitable for an entry in CECC00200 (Register of Approvals) and CECC00300 (Register of National Documents). 7) An outline drawing with main dimensions which are of importance for interchangeability, and/or reference to the appropriate national or international document for out

31、lines. Alternatively, this drawing may be given in an annex to the DS, but 7) should always contain an illustration of the general outer appearance of the component.EN181102:1994 4 BSI 04-2000 If an existing drawing from an IEC publication, or similar source, is used in a CECC specification, then it

32、 can be either first or third angle projection, but the appropriate symbol shall be shown on the drawing: The symbol in the BDS may be converted to indicate either1st or3rd angle, by deleting the inappropriate part of the drawing. Alternative outline dimensions or tolerance limits of any variants sh

33、all be shown, and may be listed in the form of a table alongside the drawing. 8) A list of variants and their identifying features covered by the DS. Enter the identification number. “AYY” for each variant of each component (see clause2.7.1 of EN181000). Assign a column in the table for each variant

34、 feature. For example, cable type, housing, orientation of ports, means of mounting etc. Instruction: max. values in dB for insertion losses between conduction ports within each specified operating wavelength range; min. values in dB for return losses, within each specified operating wavelength rang

35、e; min. values in dB for insertion losses between isolated ports within each specified operating wavelength range. 9) Supplementary information Enter the supplementary information with respect to marking of the component, marking and contents of package, ordering information, related documents, cert

36、ified test records and structural similarity. 10) Fixed-sample qualification approval test schedule Table 1 shall give the required measurements and tests for qualification by fixed-sample procedure. If qualification by lot-by-lot and periodic procedure is specified, insert “NOT APPLICABLE” inTable

37、1. If measurements or test are specified for which no basic procedure is available, or which do not appear in the GS, EN181000, each procedure shall be clearly described in an individual annex to the DS. The format and the minimum mandatory test sequence shall be the same as specified in the GS. 11)

38、 Lot-by-lot inspection test schedule When completed, Table 2 shall give the required measurements and test for qualification by lot-by-lot procedure. One or more assessment level(s) shall be given inTable 2. When differing from the preferred levels of the GS (see clause2.1.5 of EN181000) the IL and

39、AQL shall be entered and the assessment level(s) titled X, (Y) . . . etc. If measurements or tests are specified for which no basic procedure is available, or which do not appear in the GS, EN181000, each procedure shall be clearly described in an individual annex to the DS. The format and the minim

40、um mandatory test sequence shall be the same as specified in the GS. 12) Periodic C and D testing procedure Table 3 shall give the required measurements and tests for Groups C and D periodic tests. One or more assessment level(s) shall be given inTable 3. When differing from the preferred levels of

41、the GS (seeclause2.1.5 of EN181000) the IL, AQL, p, n, c and t shall be entered and the assessment level(s) titled (X, Y). 13) Details, measurements, and performance requirements Table 4 shall list the details of each tests requirements. It shall be noted that the mandatory tests have been given as

42、a minimum. Other tests shall be given in the same manner. 1st angle projection 3rd angle projectionEN181102:1994 BSI 04-2000 5 Information about manufacturers who have components qualified to this detail specification is available in the current CECC 00200 Register of Approvals. (1) Specification av

43、ailable from . (2) Page 1 of. CECC 181102- (3) ELECTRONIC COMPONENT OF ASSESSED QUALITY IN ACCORDANCE WITH GENERIC SPECIFICATION EN 181000 ISSUE 1 BLANK DETAIL SPEC. EN181102 (4)Issue. . . (5) DETAIL SPECIFICATION for FIBRE OPTIC BRANCHING DEVICE OF ASSESSED QUALITY Style: Configuration: Type: Multi

44、plexer/Demultiplexer Fibre Type(s): Connector set: Wavelength Selective Uni- or Bidirectional Transmissive Star NM Transfer matrix and numbering of ports: see page 6 (6) Assessment Level 1: Qualification Approval Procedure Climatic Category: (7) Outline dimensions and mass Panel piercing and mountin

45、g details: (7) Dimensions (mm) REF. Min. Max. Notes FIGURE. Note: mass (g): NOTEAdditional drawings (if necessary) see page. (8) Variants: Variant-No. Operating wavelength range(s) (m)EN181102:1994 6 BSI 04-2000 (8) Transfer matrices and numbering of ports: NOTE 1Values in dB. NOTE 2Create an additi

46、onal transfer matrix for each previously specified operating wavelength range. (9) SUPPLEMENTARY INFORMATION Marking of the component (add component marking requirements in accordance with clause2.7.2 of EN181000, as applicable): Marking and contents of package (add component package marking require

47、ments in accordance with clause2.7.3 of EN181000, as applicable): Ordering information (add ordering information, as applicable): Related documents (add additional related documents if not included in EN181000): Certified records of released lots (indicate whether a certificate is required): Structu

48、ral similarity (add the boundary limits in accordance with clause3.2 of EN181000):EN181102:1994 BSI 04-2000 7 (10) Table 1 Fixed sample qualification approval test schedule (11) Table 2 Lot-by-lot inspection test schedule (Groups A and B) Test Sequence (Note) EN 181000 Clause Sample size Group 0 Gro

49、up 1 Group 2 Group 3 Further groups if applicable NOTEFor details, measurements and performance requirements seeTable 4. Test Sequence (Note 1) EN 181000 Clause Assessment Level (Note 2) Group A Group B NOTE 1For details, measurements and performance requirements seeTable 4. NOTE 2See clause2.1.5 of EN181000.EN181102:1994 8 BSI 04-2000 (12) Table 3 Periodic inspection test schedule (Groups C and D) Test Sequence (Note 1) EN 181000 Clause Assessment Level (Note 2) Sample size Group C0 Group C1 Group C2 Furth