BS EN 186260-1998 Harmonized system of quality assessment for electronic components - Sectional specification connector sets for optical fibres and cables - Type SC《电子元器件质量评定协调体系 分.pdf

1、BRITISH STANDARD BS EN 186260:1998 Harmonized system of quality assessment for electronic components Sectional specification: Connector sets for optical fibres and cables Type SC The European Standard EN186260:1997 has the status of a British Standard ICS 33.160.20BSEN186260:1998 This British Standa

2、rd, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 March1998 BSI 04-1999 ISBN 0 580 29355 6 National foreword This British Standard is the English language version of EN186260:1997 publi

3、shed by the Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation was entrusted by Technical Committee EPL/86, Fibre optics, to Subcommittee EPL/86/2, Interconnecting devices and passive components, wh

4、ich has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate th

5、em in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corre

6、sponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Ca

7、talogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document c

8、omprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 10 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued si

9、nce publication Amd. No. Date CommentsBS EN 186260:1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN186260 5ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 186260 November 1997 Descriptors: Quality, electronic components, connectors English vers

10、ion Sectional Specification: Connector sets for optical fibres and cables Type SC Spcification intermdiaire: Jeux de connecteurs pour fibres et cbles optiques Type SC Rahmenspezifikation: Steckverbinderstze fr Lichtwellenleiter undLichtwellenleiterkabel Typ SC This European Standard was approved by

11、CENELEC on1994-02-07. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stan

12、dards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and not

13、ified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swede

14、n, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any

15、form and by any means reserved worldwide for CENELEC members. Ref. No. EN 186260:1997 EEN186260:1997 BSI 04-1999 2 Foreword This European Standard was prepared by the Technical Committee CENELEC TC86BXA (former WG26 of CLC/TC CECC), Fibre optic connectors. The text of the draft based on document CEC

16、C(Secretariat) 3401 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3485, it was approved as EN186260 on1994-02-07. The following dates were fixed: Document numbering for fibre optic connector specifications follows2.2(1) of CECC00700, Sect.

17、IV, in order to permit the issue of more than nine sectional specifications. The approved numbering system applicable to fibre optic connector specifications is illustrated in the following diagram: latest date by which the EN has to be implemented at national level by publication of an identical na

18、tional standard or by endoresement (dop) 1998-08-15 latest date by which the national standards conflicting with the EN have to be withdrawn (dow)1999-08-15EN186260:1997 BSI 04-1999 3EN186260:1997 BSI 04-1999 4 Contents Page Foreword 2 1 General 5 1.1 Scope 5 1.2 Related documents 5 1.3 Definitions

19、5 1.4 Safety 5 1.5 Marking 5 2 Requirements 5 2.1 Classification 5 2.2 Reference 9 2.3 Gauges 9 3 Quality assessment procedures 9 3.1 Qualification approval 9 3.2 Quality conformance inspection 10 3.3 Delayed deliveries 10 Figure 1 Plug mating-face limit dimensions 6 Figure 2 Adaptor mating face lim

20、it dimensions 8EN186260:1997 BSI 04-1999 5 1 General 1.1 Scope This sectional specification covers a family of single way fibre optic connector sets which are classified astype SC. Type SC is a connector set of the plug-adaptor-plug configuration. It features a push-pull coupling mechanism and cylin

21、drical butting ferrules. The optical alignment mechanism is a split sleeve contained within the adaptor. The specification contains the requirements for type SC connector sets. Detail specifications (DSs) shall be prepared using the following pro forma general blank detail specifications (BDSs) asso

22、ciated with the generic specification. For example: EN 186005 for environmental category V. When completed, the DS(s) applicable to this SS shall be numbered in accordance with CECC00700 (Section IV) Issue1, clause4.2, as follows. For example: CECC86265-000, Type SC, environmental category V. 1.2 Re

23、lated documents The following standards contain provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this standard are encoura

24、ged to investigate the possibility of applying the most recent editions of the standards listed below. References made to a specific clause or sub-clause of a standard includes all sub-clauses to the reference unless otherwise specified. EN 186000-1, Generic specification for connectors for optical

25、fibres and cables. IEC 825-1, Safety of laser products Part1:Equipment classification, requirements and users guide. IEC 825-2, Safety of laser products Part2: Safety of optical fibre communication systems. 1.3 Definitions All necessary definitions are given in EN186000-1. 1.4 Safety 1.4.1 Optical F

26、ibre Connectors, when used as part of an Optical Fibre System, may emit/produce potentially hazardous radiation. The manufacturers of connectors are not obliged to mark them as such, but sufficient information should be made available in the manufacturers literature to enable the system designer to

27、assess the degree of hazard. This information shall be given prominence in the detail specification (DS). 1.4.2 The assembly instructions, included in the connector package, shall give a prominent warning to the assembler, of the necessary safe work practices. 1.4.3 The responsibility for the safe a

28、pplication of the connector lies with the system design engineer, who should refer to IEC825-1. As there is no safety guide for light emitting diodes (LEDs), IEC825-1 shall apply to systems using these also. 1.4.4 DSs should give the following information in a prominent position: WARNING “Care shoul

29、d be taken when handling small diameter optical fibre, to prevent it puncturing the skin, especially in the eye area. Direct viewing of the end of an optical fibre or a terminated optical fibre, while it is propagating energy is not recommended unless prior assurance has been obtained as to the safe

30、 energy of the output level”. 1.5 Marking See 2.6 of EN186000-1. 2 Requirements The requirements specified in sections 2 and 3 of EN186000-1 apply. The requirements for connector sets components covered by this specification are as specified herein and in the relevant DS. 2.1 Classification The conn

31、ector sets covered by this specification are classified as: Type: type 1: SC, coupling mechanism: push-pull, configurations: plug / adaptor / plug Arrangements: kit, pigtail, patchcord.EN186260:1997 6 BSI 04-1999 Environmental categories: the DS-writer shall select the appropriate BDS for the chosen

32、 environmental category. Assessment levels: level A, level B, level C. The single limit (maximum or minimum) mating face dimensions for connector set configurations are given in Figure 1 and Figure 2. The applicable configuration, arrangement, style, variants, climatic category and assessment levels

33、 shall be specified in the DS. Figure 1 Plug mating-face limit dimensionsEN186260:1997 BSI 04-1999 7 REF MM NOTES MIN. MAX. A 2,500 1 B 4,80 C 7,4 D 5,3 E 6,8 F 23 Degree G 35 Degree H 7,15 2 I 0,80 J 5,5 K 0,05 L 2,11 3 M 2,8 3,4 N 6,8 O 1,8 P 8,99 Q 0,8 R 7,39 S 0,9 T 4,05 U 5,4 V 0,5 3 BC 0,5 NOT

34、E 1A chamfer or radius is allowed to a maximum depth of1,2mm from the ferrule endface. A diameter of the ferrule endface shall be more than0,80mm. NOTE 2Dimension H shown in Figure 1 is given for a plug endface when not mated. It is noticed that a ferule is moveable by certain axial compression forc

35、e with direct contacting end faces and therefore dimension H is variable. This dimension after contacting shall be # 7,1mm. NOTE 3The coupling sleeve shall be movable toward the right-and the left-directions. These dimensions are given when the coupling sleeve is moved in its most right-direction po

36、sition. NOTE 4M should be below0mm, when a coupling sleeve is moved in its most left-direction position. NOTE 5Surface roughness shall be specified in the Detail Specification. Figure 1 Plug mating face limit dimensions (continued)EN186260:1997 8 BSI 04-1999 Figure 2 Adaptor mating face limit dimens

37、ionsEN186260:1997 BSI 04-1999 9 2.2 Reference components Reference component(s), if required, shall be defined in the DS. 2.3 Gauges Gauge(s), if required, shall be defined in the DS. 3 Quality assessment procedures The quality assessment procedures of EN186000-1 section 3 apply. 3.1 Qualification a

38、pproval 3.1.1 Qualification by fixed sample procedure When specified, the fixed sample procedure shall be in accordance with 3.3.1 of EN186000-1. The relevant BDS contains the minimum mandatory test and performance requirements for qualification by the fixed sample procedure. The complete set of man

39、datory test schedules and performance requirements shall be specified in theDS. Qualification approval is granted for the complete range of variants submitted as structurally similar upon successful completion of the tests. Sample size The sample size for qualification by fixed sample procedure shal

40、l be as specified in the DS. The specimens shall be complete connector sets of a variant for the smallest fibre core diameter specified in the DS. REF MM NOTES MIN. MAX. A 1 B 4,79 D 4,9 H 7,1 I 0,8 J 5,51 K 0,06 L 2,1 O 2,0 P 9,0 R 7,4 S 1,0 T 4,04 U 5,3 V 0,6 AA 33 Degree AB 0,8 AC 0,4 AD 0,8 AE 0

41、,6 BA 5,6 BB 11,2 2 NOTE 1The connector alignment feature may be a rigid hole or a resilient alignment sleeve and must accept a maximum diameter plug of2,500mm. When a resilient alignment sleeve is used, the dimensional requirement may be replaced by a gauge insertion and/or retention requirement in

42、 the detail specification. NOTE 2It may be of a structure as shown by an alternate long and short dash line shown in Figure 2. NOTE 3Surface roughness shall be specified in the relevant Detail Specification. Figure 2 Adaptor mating face limit dimensions (continued)EN186260:1997 10 BSI 04-1999 Follow

43、ing completion of the group “0” tests, the specimens for the other groups shall be randomly selected from the group “0” specimens. In addition, the following specimens shall be provided: one specimen of each plug variant to be qualified by structural similarity to the one used for group “0”, one spe

44、cimen of each adaptor variant to be qualified by structural similarity to the one used for group “0”, one specimen of each socket variant to be qualified by structural similarity to the one used for group “0”. Preparation of specimens Test specimens for kit arrangements shall be terminated using the

45、 smallest fibre core diameter specified in the DS. The fibre/cable type and lengths to be used for all arrangements shall be as specified in the DS. Testing The tests shall be conducted in the order given, using the method specified. The specimens shall satisfy the performance requirements of the DS

46、. The additional variant specimens selected shall be tested to all group “0” tests and shall meet the requirements of the DS. 3.1.2 Qualification by lot-by-lot and periodic procedure When specified, the lot-by-lot plus periodic qualification procedure shall be in accordance with3.3.2 of EN186000-1 (

47、see3.2.1 and3.2.2 for test schedules). Qualification approval will be granted for the complete range of variants submitted as structurally similar upon successful completion of the tests. 3.2 Quality conformance inspection 3.2.1 Lot-by-lot inspection The minimum mandatory inspection schedules for lo

48、t-by-lot inspection are specified in the relevant BDS. The complete set of mandatory test schedules and performance requirements shall be specified in the DS. 3.2.2 Periodic inspection The minimum mandatory periodic test schedules are specified in the relevant BDS. The complete set of mandatory test

49、 schedules and performance requirements shall be specified in the DS. Periodic inspection approval will be granted for the complete range of variants submitted as structurally similar upon successful completion of the tests. Sample size The sample size for periodic inspection shall be as specified in he DS. The specimens shall be complete connector sets of a variant for the smallest fibre core diameter s