BS EN 28474-1987 Complete filled transport packages - Method for determination of resistance to immersion in water《满包运输包装件 耐浸水性能测定方法》.pdf

1、BRITISH STANDARD BS EN 28474:1993 ISO 8474:1986 Incorporating Amendment No. 1 Complete, filled transport packages Method for determination of resistance to immersion in water The European Standard EN 28474:1992 has the status of a British Standard UDC 621.798.1:620.165.7BSEN28474:1993 This British S

2、tandard, having been prepared under thedirectionof the PackagingandFreight ContainersStandards Committee,waspublished underthe authorityof the BoardofBSIand comesintoeffecton 30 September 1987 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference PKM/501 D

3、raft for comment 85/44444 DC ISBN 0 580 16091 2 Committees responsible for the British Standard The preparation of this British Standard was entrusted by the Packaging and Freight Containers Standards Committee (PKM/-) to Technical Committee PKM/501, upon which the following bodies were represented:

4、 Association of Drum Manufacturers British Fibreboard Packaging Association Chemical Industries Association Department of Trade and Industry (Laboratory of the Government Chemist) Electronic Components Industry Federation Glass Manufacturers Federation Institute of Packaging Ministry of Defence PIRA

5、 (The Research Association for the Paper and Board, Printing and Packaging Industries) Society of Motor Manufacturers and Traders Limited Telecommunication Engineering and Manufacturing Association (TEMA) Timber Research and Development Association Amendments issued since publication Amd. No. Date o

6、f issue Comments 7464 March 1993 Indicated by a sideline in the marginBSEN28474:1993 BSI 10-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 28474 3 Publication referred to Inside back coverBSEN28474:1993 ii BSI 10-1999 National foreword This

7、Part of BS 4826 has been prepared under the direction of the Packaging and Freight Containers Standards Committee. It is identical with ISO8474:1986 “Packaging Complete, filled transport packages Water immersion test”, published by the International Organization for Standardization (ISO). In 1992 th

8、e European Committee for Standardization (CEN) accepted ISO8474:1986 as European Standard EN28474:1992. As a consequence of implementing the European Standard this British Standard is renumbered as BSEN28474 and any reference to BS4826-13 should be read as a reference to BSEN28474. Terminology and c

9、onventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. Wherever the word

10、s “International Standard” appear, referring to this standard, they should be read as “Part of BS4826”. Cross-reference. The Technical Committee has reviewed the provisions of ISO2233, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this s

11、tandard. A related British Standard is BS4826 “Complete, filled transport packages” Part 2:1986 “Method of conditioning for testing”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. C

12、ompliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2to4, an inside back cover and a back cover. This standard has been updated (see copyright

13、date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 28474 November 1992 UDC 621.798.1:620.165.7 Descriptors: Packing, transport packing, complete- and filled packages, tests, wate

14、r resistance, immersion tests, water English version Packaging Complete, filled transport packages Water immersion test (ISO 8474:1986) Emballages dexpdition complets et pleins Essai dimmersion dans leau ISO 8474:1986) Verpackung Fertige, gefllte Transportverpackungen Wassereintauchprfung (ISO 8474:

15、1986) This European Standard was approved by CEN on 1992-10-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical re

16、ferences concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member

17、 into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden

18、, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref. No. EN 28474:1992 EEN28474:1992 BSI 10-1999 2 Foreword In 19

19、91, ISO 8474:1986 Packaging Complete, filled transport packages Water immersion test was submitted to the CEN Primary Questionnaire procedure. Following the positive result of the CEN/CS Proposal ISO8474:1986 was submitted to the Formal Vote. The result of the Formal Vote was positive. This European

20、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1993, and conflicting national standards shall be withdrawn at the latest by May1993. According to the CEN/CENELEC Internal Regulations, the following countri

21、es are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword 2 1 Scope and field of application 3 2 Reference 3 3 P

22、rinciple 3 4 Apparatus 3 5 Package preparation 3 6 Conditioning 3 7 Procedure 3 8 Test report 4EN28474:1992 BSI 10-1999 3 1 Scope and field of application This International Standard specifies a test method for the immersion in water of complete, filled transport packages. It may be used to pre-cond

23、ition a package prior to other tests, to investigate reduction in strength caused by exposure to water or to investigate the protection the package gives to its contents from water immersion. The test is principally intended for packages which are waterproof or which are intended to provide some deg

24、ree of “waterproofness”. The test is performed on the package as prepared for transport and may form part of a test sequence. 2 Reference ISO 2233, Packaging Complete, filled transport packages Conditioning for testing. 3 Principle Conditioning of the package, followed by complete immersion in water

25、, removal and draining and drying in the conditioning atmosphere. The time of immersion, time of draining and drying and the atmospheric conditions are predetermined. 4 Apparatus 4.1 Test area, conditioned in such a manner that evaporation from the wet package and the surface of the water in the wat

26、er tank(4.2) do not significantly change the atmospheric conditions. 4.2 Water tank, sufficiently large for the test package to be immersed completely under water with the water level at least100mm above the package. The tank shall be designed so that it can be easily filled with water and emptied a

27、nd the water maintained at the temperature specified in7.1. 4.3 Immersion equipment to contain the test package loosely. It shall be capable of being lowered and lifted. A cage of appropriate dimensions is suitable for this purpose. NOTESome means of hoisting, for example an electric or manual hoist

28、, may be fitted over the water tank to lower and raise the test package conveniently. 4.4 Rigid grill, capable of supporting the wet test package without deformation and positioned so that air is able to flow freely beneath it. The rods or bars from which it is made shall not occupy more than10% of

29、the surface area. 5 Package preparation The test package shall normally be filled with its intended contents. However, under certain circumstances, simulated or dummy contents may be used, on condition that the dimensions and physical properties of the such contents shall be as close as possible to

30、those of the intended contents. Ensure that the test package is closed, and labelled or marked normally, as if ready for distribution. If simulated or dummy contents are used, ensure that the normal methods of closure, and labelling or marking are still employed. 6 Conditioning The package shall be

31、conditioned in accordance with one of the conditions specified in ISO2233. 7 Procedure 7.1 Fill the tank(4.2) to an appropriate depth with water and ensure that the water temperature is within 2 C of the temperature selected from a range from 5to40 C. 7.2 The test shall be begun within5min of removi

32、ng the package from the atmospheric conditions selected for clause6. 7.3 Using the immersion equipment (4.3), lower the package into the water at a rate not greater than300mm/min. Alternatively the package may be placed in the empty water tank which is then filled to the required level. The immersio

33、n process shall be considered to be complete when the water level is at least100mm above the top of the package. Keep the package immersed for a period which shall be selected from 5, 15 or 30 min, or from 1, 2 or 4h. 7.4 After the predetermined immersion period, raise the package completely out of

34、the water at a rate not exceeding300mm/min. Place the package on the grill(4.4) positioned so that all surfaces of the package are exposed to the atmospheric conditions specified in clause6. Allow the package to be exposed for a period which shall be selected from 4, 8, 16, 24, 48 or 72 h or from 1,

35、 2, 3 or 4 weeks.EN28474:1992 4 BSI 10-1999 7.5 Note any obvious damage sustained by the package and its contents as a result of immersion in water and subsequent draining and drying, and any other difference in appearance, including labels and markings. 8 Test report The test report shall include t

36、he following information: a) reference to this International Standard; b) the number of replicate packages tested; c) a full description of the package, including dimensions, structural and material specifications of the package and its fittings, cushioning, blocking or reinforcing arrangements; d)

37、a description of contents if simulated or dummy contents were used, full details shall be given; e) the gross mass of the package and the mass of the contents, in kilograms; f) the relative humidity, temperature and time of conditioning; a statement whether these values comply with the requirements

38、of ISO2233; g) the temperature of the test area and of the water at the time of immersion; h) the orientation of package relative to the floor during immersion and draining, etc.; i) the duration of immersion in water; j) the duration of the draining and drying method; k) any deviations from the tes

39、t method specified in this International Standard; l) a record of the result, with any observations which may assist in correct interpretation; m) the date of the test; n) the signature of the person responsible for the test.BSEN28474:1993 BSI 10-1999 Publication referred to See national foreword.BS

40、 EN 28474:1993 ISO 8474:1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re

41、visions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or am

42、biguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers aut

43、omatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI

44、 implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electron

45、ic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of stan

46、dards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted unde

47、r the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implem

48、enting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.