BS EN 50289-3-12-2001 Communication cables - Specifications for test methods - Mechanical test methods - Shot gun damage《通信电缆 试验方法规范 机械试验方法 强迫性损伤》.pdf

1、BRITISH STANDARD BS EN 50289-3-12:2001 Communication cables Specifications for test methods Part 3-12: Mechanical test methods Shot gun damage The European Standard EN 50289-3-12:2001 has the status of a British Standard ICS 29.060.20; 31.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY

2、COPYRIGHT LAWBS EN 50289-3-12:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 30 November 2001 BSI 30 November 2001 ISBN 0 580 38750

3、X National foreword This British Standard is the official English language version of EN 50289-3-12:2001. The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wire and waveguides, RF connectors, and accessories for communication and signalling, to Subcommittee

4、 EPL/46/1, Communication cables, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be fo

5、und in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standar

6、ds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep t

7、he UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright date displayed in this document indicate

8、s when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50289-3-12 NORME EUROPENNE EUROPISCHE NORM August 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komit

9、ee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-3-12:2001 E ICS 33.120.10 English version Communication cables - Specifications

10、for test methods Part 3-12: Mechanical test methods - Shot gun damage Cbles de communication - Spcifications des mthodes dessai Partie 3-12: Mthodes dessais mcaniques - Dommages par les coups de fusil Kommunikationskabel - Spezifikationen fr Prfverfahren Teil 3-12: Mechanische Prfverfahren - Beschdi

11、gung durch Schrotkugelbeschuss This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-

12、date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation und

13、er the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland,

14、Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 50289-3-12:2001 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 46X, Communication cables. The text of the draft was submitted to the Unique Acceptance

15、 Procedure and was approved by CENELEC as EN 50289-3-12 on 2001-05-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-04-01 latest date by which the national standards c

16、onflicting with the EN have to be withdrawn (dow) 2004-04-01 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association.- 3 - EN 50289-3-12:2001 Contents 1 Scope 4 2 Normative references. 4 3 Definitio

17、ns . 4 4 Test method. 4 4.1 Sample 4 4.2 Equipment. 4 4.3 Procedure 5 4.4 Details to be specified . 5 5 Requirements 5 6 Test report . 5EN 50289-3-12:2001 - 4 - 1 Scope This Part 3-12 of EN 50289 details the method of test to determine the ability of a cable used in analogue and digital communicatio

18、n systems to withstand shot-gun damage. It is to be read in conjunction with Part 3-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative re

19、ferences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references t

20、he latest edition of the publication referred to applies (including amendments). EN 50289-3-1 2001 Communication cables - Specifications for test methods - Part 3-1: Mechanical test methods - General requirements EN 50290-1-2 1) Communication cables - Part 1-2: Definitions 3 Definitions For the purp

21、oses of this European Standard the definitions of EN 50290-1-2 apply. 4 Test method 4.1 Sample A length of cable (typically 3 m in length). 4.2 Equipment The apparatus consists of : a) a shot-gun, as specified in the Detail Specification; NOTE 1 The type of gun is likely to vary from country to coun

22、try. b) a frame for holding the cable sample. It is important that the sample is free to move and the test set-up should also take into account that the shot may scatter in an elliptical manner depending on the gun used; c) gun shot : - size 4 or 7 or as specified in the Detail Specification ; NOTE

23、2 The shot size is likely to vary from country to country, and should represent the hazard particular to the installation. - the shot type shall be specified in the Detail Specification ; NOTE 3 Typically lead or steel is used, depending on the country. Lead shot deforms on impact and is less damagi

24、ng than steel shot. - the cartridge type shall be specified in the Detail Specification.1)At draft stage.- 5 - EN 50289-3-12:2001 4.3 Procedure The cable sample shall be mounted on the frame and shot at from the distance specified in the Detail Specification. A typical distance is 20 m. The number o

25、f shots with visible impact should be low, typically three or less, in order to give a reproducible test. If more than three shots hit the cable, then the test may be repeated if any of the requirements are not met. 4.4 Details to be specified The detail specification shall include : a) gun type, b)

26、 shot size, c) shot type, d) cartridge type, e) distance between gun and sample. 5 Requirements The acceptance criteria for the test shall be stated in the relevant Detail Specification. Typical failure modes include damage to the cable core elements and cable sheath (e.g. piercing of loose tubes) a

27、nd loss of continuity. 6 Test report The test report shall include: - temperature; - sample length; - details of test configuration, including cable orientation; - report of damage inflicted, including fibre and conductor continuity; - report of damages on sheath and screens; - number of tests carri

28、ed out, to achieve minimum visible impacts; - pass/fail criteria.BS EN 50289-3-12:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at th

29、e international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv

30、ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. T e l :0 2 08 9 9 69 0 0 0 . F a x :0 2 08 9 9 67 4 0 0 . BSI off

31、ers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8

32、996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provide

33、s a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. T e l :

34、0 2 08 9 9 67 1 1 1 . F a x :0 2 08 9 9 67 0 4 8 . Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020

35、8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs

36、 and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of

37、necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.