BS EN 50289-4-9-2001 Communication cables - Specifications for test methods - Environmental test methods - Pneumatic resistance《通信电缆 试验方法规范 环境试验方法 耐气动性》.pdf

1、BRITISH STANDARD BS EN 50289-4-9:2001 Communication cables Specifications for test methods Part 4-9: Environmental test methods Pneumatic resistance The European Standard EN 50289-4-9:2001 has the status of a British Standard ICS 33.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COP

2、YRIGHT LAWBS EN 50289-4-9:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 14 November 2001 BSI 14 November 2001 ISBN 0 580 38693 7 Na

3、tional foreword This British Standard is the official English language version of EN 50289-4-9:2001. The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wire and waveguides, RF connectors, and accessories for communication and signalling, to Subcommittee EPL/

4、46/1, Communication cables, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found i

5、n the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards ar

6、e responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK

7、 interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright date displayed in this document indicates whe

8、n the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50289-4-9 NORME EUROPENNE EUROPISCHE NORM October 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr

9、 Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-4-9:2001 E ICS 33.120.10 English version Communication cables - Specifications for te

10、st methods Part 4-9: Environmental test methods - Pneumatic resistance Cbles de communication - Spcifications des mthodes dessai Partie 4-9: Mthodes dessais denvironnement - Rsistance pneumatique Kommunikationskabel - Spezifikationen fr Prfverfahren Teil 4-9: Umweltprfverfahren - Pneumatischer Wider

11、stand This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp

12、hical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

13、a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembour

14、g, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 50289-4-9:2001 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 46X, Communication cables. The text of the draft was submitted to the formal vote and was approved by CENE

15、LEC as EN 50289-4-9 on 2001-05-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-04-01 latest date by which the national standards conflicting with the EN have to be wi

16、thdrawn (dow) 2004-04-01 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association.- 3 - EN 50289-4-9:2001 Contents 1 Scope 4 2 Normative references 4 3 Definitions. 4 4 Test method 4 4.1 Equipment 4

17、4.2 Test sample . 4 4.3 Procedure 4 5 Requirements 5 5.1 Details to be specified 5 6 Test report 5EN 50289-4-9:2001 - 4 - 1 Scope This Part 4-9 of EN 50289 details the method of test to determine the pneumatic resistance used in analogue and digital communication systems. This test only applies to c

18、ables which are protected by gas pressurisation. It is to be read in conjunction with Part 4-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These nor

19、mative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated ref

20、erences, the latest edition of the publication referred to applies (including amendments). EN 50289-4-1 2001 Communication cables - Specifications for tests methods Part 4-1: Environmental test methods - General requirements EN 50290-1-2 1) Communication cables - Part 1-2: Definitions 3 Definitions

21、For the purposes of this European Standard, the definitions of EN 50290-1-2 apply. 4 Test method 4.1 Equipment Pneumatic equipment to supply a regulated pressure of air to the sample, flow-meter, barometer and thermometer. 4.2 Test sample The sample of finished cable having a sufficient length to ca

22、rry out the test specified. 4.3 Procedure The ambient temperature and barometric pressure shall be measured. A length of finished cable shall have one end connected to a steady state flow of dry air supplied by a pressure regulated source providing air with a dryness of 5 % RH or better at 20 C. The

23、 other end of the cable shall be open to the atmosphere.1)At draft stage.- 5 - EN 50289-4-9:2001 The pressure applied across the cable shall be 62 kPa 2 % and the steady state air flow shall be recorded using a flow-meter calibrated to 10 %. Other pressures may be applied in accordance with particul

24、ar user requirements and specified in the Detail specification. Only those air paths which access the interior of the sheath shall be used in the measurement. A second measurement shall be made with the air flow direction reversed and the results shall be recorded separately. The pneumatic resistanc

25、e is derived from : Pneumatic resistance L x f 720 3 = kPa x m 3 /s x m where L = the sample length (m), f = the flow (m 3 /s). 5 Requirements The pneumatic resistance shall comply with the maximum value given in the detail specification. 5.1 Details to be specified The detail specification shall me

26、ntion - maximum pneumatic resistance, - sample length, - pressure, if different from 62 kPa. 6 Test report The test report shall include - test conditions, - test temperature, - pneumatic resistance, - pass/fail criteria.BS EN 50289-4-9:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Stand

27、ards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British St

28、andards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the techn

29、ical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orde

30、rs for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BS

31、I implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electr

32、onic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price

33、 of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in th

34、e UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without

35、prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.